customer service | view cart  View Cart

2010 Ford Explorer Accessories

change vehicle

Popular Ford Explorer Accessories





2010 Ford Explorer Questions and Answers


  • Where Does a Trailer Brake Controller Plug Into On a 2010 Ford Explorer
  • If your 2010 Ford Explorer came with a factory 7-Way trailer connector then you will use brake controller wiring harness # 3035-P which installs in a connector behind the passenger side glove compartment. I have linked a video showing a typical installation and a link to the installation instructions for the harness. If your Explorer came with a 4-Way flat connector but not a 7-Way, the connector behind the glove box may still be there but the blue wire for brake output will not be run all th
    view full answer...

  • Hopkins Tailgate Lift Assist Compatibility with 2013 Dodge Ram
  • We do have a tailgate assist options for your 2013 Dodge Ram 1500 Laramie, however, I spoke with my contact at Hopkins and he confirmed that the Hopkins Tailgate EasyLift, # 74211, will not fit the newer generation Dodge trucks (2009 to 2013) due to the internal structure of the tailgate. For your truck, I recommend the DeeZee Tailgate Assist Lowering System, # DZ43300. This system uses a shock absorber to make lowering your tailgate smooth and easy. I have attached a link to the installatio
    view full answer...

  • Will a Yakima Big Horn fit a 2010/2011 Ford Explorer
  • To determine if the Yakima Big Horn # Y02404 will fit your Ford Explorer you will need to take one important measurement. You will need to measure the distance from the center of the hitch pin out to the furthest point out of the rear of your vehicle. The # Y02404 measures 11-1/8 inches from the center of the hitch pin out to the nearest upright bar, so if the distance you measure on your vehicle is less than that this rack will work for you. Check out the installation instructions and rev
    view full answer...

  • Fit of Curt 20x48 Cargo Carrier # C18145 on 2010 Ford Explorer
  • To determine if the Curt 20x48 Cargo Carrier will work with your Explorer, you will need determine if there is enough clearance at the rear of the vehicle. You will need to measure the distance from the hitch pin hole in your receiver to the furthest rearward portion of your bumper. If this distance is less than the 6 inch hitch pin hole to edge of basket dimension of the carrier, the # C18145 will work great for you. For install details or to see a product demonstration video, click the p
    view full answer...

  • Availability of an Indianapolis Colts Hitch Cover For a 1-1/4 Inch Trailer Hitch
  • For a 1-1/4 inch trailer hitch we have Colts hitch cover # FTH050TG which is designed to fit 1-1/4 or 2 inch receivers. For any hitch cover, I recommend adding a lock, like # 40106, to deter theft of the cover off of a 1-1/4 inch hitch.
    view full answer...

  • Recommendations for Carrying Bikes And a Cargo Bag at the Rear of a 2010 Ford Expedition
  • It sounds like your best option would be a small trailer. The Magneta Sports Trailer, # RRT60, would be a great choice for hauling bikes and cargo and will store in not much more space than a hitch mounted cargo carrier and a bike rack if stood on end. You could put one bike on each side of the trailer and then put the etrailer.com Extra Large Cargo Carrier Bag, item # 988501, in between the bikes. At this time I do not have an option for carrying bikes, a cargo carrier and a cargo bag al
    view full answer...

  • Will the Curt Class lll Trailer Hitch for 2010 Ford Explorer Fit with Factory Hitch and Spare Tire
  • Yes, the Curt Class III Trailer Hitch, item # 13112, will fit on your 2010 Ford Explorer, with factory 1-1/4 inch hitch. Since your vehicle is equipped with the factory hitch you cannot use both hitches at the same time, damage to the hitch or vehicle would result. You will reinstall the full size spare tire in the original location, should you find it necessary to remove it, to ease installation of the Curt hitch.
    view full answer...

  • How Does the EGR Superguard Bug Shield Hood Protector # 303611 Secure to a 2010 Ford Explorer
  • The majority of what holds this EGR Superguard Bug Shield Hood Protector, part # 303611, is the factory scrivets that are in the middle of the grille. The two screws that go on the outer portion help secure it, but more screws would not be necessary to secure this to your 2010 Ford Explorer. The screw plugs will install in outer wing holes in the underside of the hood. They should snap right into what looks like slots on the underside of the hood near the outer edges.
    view full answer...

  • Replacement 7-Way Wiring Harness for a 2010 Expedition EL with Existing 4 Pin Plug
  • The 2010 Ford Expedition should have a round connector at the rear of the vehicle where your 4 pin plug is plugged in. If there is a round connector there you can use the Replacement Multi-Tow 7-Way and 4 Pole Trailer Connector, item # 20119, to replace the 4-Way OEM connector on your Expedition. If your Expedition does not have the mating round connector under the rear of the vehicle you will need to use a 4-Way to 7-Way adapter like item # 37185, to provide a 7-Way connector at the rear of
    view full answer...

  • Is Trimming Required for Installation of the # 31545 Front Mount Hitch on a 2010 Ford Explorer XLT
  • There is no drilling, cutting or modifying of any of the parts on your 2010 Ford Explorer XLT for installation of the Curt Front Mount Trailer Hitch Receiver, item # 31545. I have provided a link to the installation details for you to review. You may also be interested in the DeadBolt Stainless Steel Flush Design Hitch Receiver Lock, item # 40107, to secure you accessories in the front mount hitch on your vehicle.
    view full answer...

  • Where Is Factory Brake Controller Plug Located On 2010 Ford Explorer Sport Trac
  • On your 2010 Ford Explorer Sport Trac the factory plug for your brake controller will be located under the dash, on the left side of the steering wheel, just above your left leg. The wiring adapter you will need to connect the Draw-Tite Brake Controller # 5500 to your vehicle is the Draw-Tite Brake Control Wiring Adapter # 20260. This adapter will have a 6-pin plug that will connect to your factory brake controller plug and the 4 wires on the other end will be butt-connected to the 4 wires o
    view full answer...





Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email




etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com