Tube Steps and Running Boards
Need easier access to the cab of your truck? Enhance your truck or SUV's appearance and functionality with a set of tube steps or nerf bars from DeeZee, Bully, Bestop, Amp Reasearch, Putco or Westin. Custom-fit installation kits ensure the perfect fit and ease of installation on your truck. These rugged step bars make it easy to step into your cab and also give your vehicle a finished, stylish appeal.
Many different nerf bar styles and finishes are available for popular vehicle manufacturers such as Ford, Chevy, Toyota, Cadillac, Nissan, and Dodge. Find the custom-fit tube steps or nerf bars for your vehicle by entering the year, make, and model on the left.
What our customers are saying:
Thanks for the great service!!!!
Ron
Rochester, NY
Westin Nerf Bars Installation - 2006 Dodge Ram
Today on our 2006 Dodge Ram pickup, well be installing the Westin E-Series Three Inch Round Nerf Bars, part number 23-2320. Note, before we being our install, each process we do to one side will get repeated identically on the opposite side. To start our install well first remove the manufacturers body mount bolts. This will be a bolt and washer combination. Now with that removed were ready to go ahead and start installing the front and rear brackets. Securing the front and rear brackets well use the new 12 millimeter bolt along with a flat washer and lock washer.
Carr Super Hoop Side Step Installation - 2012 Dodge Ram
Today on our 2012 Dodge Ram pickup, we'll be installing the Carr custom fit sidesteps, part number carr125772. Step one of our install will be assembling the brackets to the step using the 7/16 bolts and 7/16 flat washers. We'll go ahead and slide the flat washer onto the bolt and then run the bolt through the bracket, through the step and then back through the step and bracket. We'll secure it with a 7/16 flat washer and nylon lock nut. We'll install each fastener finger tight this time. Now with one bracket installed with two bolts, we'll go ahead and repeat the same process on the other side.
Putco Box Board Running Boards Installation - 2005 Ford F-350
Today on our 2005 Ford F350 Super Duty well be installing the Putco Master Boss rounded running board, box board, part number P62522. Note, on this application well need to trim the rear edge in order for it to fit properly with the dual rear wheel setup on this vehicle. First well go ahead and take a straight edge, mark the line and then cut off the top edge. Now with that done were ready to go ahead and install the front end cap. This will be a black cap secured with two cap screws and a quarter inch flange nut. Then well move to the rear flap, or cap, which will be a large polished sheet of steel that well need to remove the protective film from.
Putco Running Boards Installation - 2005 Ford F-350
Today on our 2005 Ford F350 Super Duty well be installing the Putco Master Boss round running board, part number P62135. First before we install the running boards well need to do some preassembly. Well go ahead and take the drivers side running board, sit it out on a flat surface and install the front cap, or fender flare. Well use the cap screws and flange nuts to secure it. Then well move to the rear of the running board and install the rear cap. Again well use the cap screws and flange nuts to secure it.
Pilot Tube Step Installation - 2003 Dodge Ram
Today on this 2003 Dodge Ram pickup were going to install part #: NB-210. All right, to start off our install were going to go ahead and lay down our parts according to the instructions and where we located that. Well unbolt the body bolt closest to the bed first and then well install our first bracket. This will be the long bracket. Well install new hardware and well also install a spacer washer in between and then well go ahead and reinstall it and then well go ahead and install it into the truck, leaving it snug, but not tight. Then well go up to the front of the vehicle and with the body mount going towards the front well repeat the same process.
Bestop TrekStep Truck Bumper Step Installation - 2012 GMC Sierra
All right, today on this 2012 GMC Sierra were going to install part #: B75300 from Bestop, this is their Trekstep. First thing we need to do is locate the rear bumper attachment point on the driver side of the vehicle. Therell be two bumper fasteners that we have to remove. This vehicle has two in package, so well remove the two bolts. All right, well leave that alone from now and well go to the Trekstep. Well go ahead and do some subassembly.
Bestop PowerBoard Motorized Running Boards Review
Today, we're reviewing the Bestop PowerBoard Motorized Running Boards with LED Lights, part number B7510415. The PowerBoards quickly and quietly lower as your doors open and retract as they close maintaining vehicle's original ground clearance. The built-in LED lights on the running boards ensure safe entry and exit. The boards retract automatically when doors close and open when the doors open. The running boards are made of a cast aluminum construction with black powder coat finish for durability. The motor of the running boards is waterproof, quick, quiet, smooth and reliable.
