Free Shipping on Orders Over $99
Custom fit Throttle Body Spacer for your:
What our customers are saying:
Thank you so much for your prompt service. Heidi
Airaid Throttle Body Spacer AR300-574 Review
Today we're going to take a look at the Air A Power A Custom Throttle Body Spacer. Now this is a custom fit part. It is designed to fit the 2002-2007 Dodge Dakota and Durango's with the 4.7 liter V-8 engine and also the 2006-2009 Mitsubishi Raider also with the 4.7 liter V-8 engine. Now on any custom fit part, I always like to recommend to go our website, use our fit guide, put in your year and model vehicle, and that'll show you if this will work for your application. This part includes everything laid out here on the table, includes the actual power plate, the O-ring, throttle cable bracket, the extension plates, some spacers, and then the bolts and screws which are the mounting hardware for all this. It comes with a nice set of detailed instructions to show you how to install this. This part will improve your engine torque, your horsepower, and the fuel efficiency.
Airaid EconoAid Throttle Body Booster Installation - 2012 Toyota 4Runner
Today on our 2012 Toyota 4Runner we'll be installing the AIRAID EconoAid Throttle Body Booster, part number AR1027. While we are installing this on a 2012 Toyota 4Runner, note that this throttle body spacer fits most late model Toyota vehicles and it installs roughly in the same fashion. Please consult our website to ensure that this is a fit for you. To begin with, we'll need to raise the hood of the vehicle. Next we'll need to go ahead and lift off the cover that covers the top part of the motor as well as the throttle body. We'll begin here by taking a 10 millimeter socket and loosening up the hose clamp that holds the tube from the air filter to the throttle body on the airbox side. With that done, we can go ahead and undo the three tabs that hold the cover to the airbox. When we lift up the cover to the airbox, it'll go ahead and slide off the boot.
Airaid EconoAid Throttle Body Booster Installation - 2012 Jeep Grand Cherokee
Today on our 2012 Jeep Grand Cherokee, we'll be installing the AirAid EconoAid throttle body booster part number AR1022. To begin with, we'll need to go ahead and raise the hood of the vehicle. Then, we'll need to remove this plastic cover that covers the top part of the engine. You just simply lift up on it and the tabs that hold it in place will release. We can go ahead and set that aside for now. Now we can see here, we're going to need to loosen up two hose clamps. We'll begin here at the air box side where we'll loosen up the hose clamp enough, so we can slide the boot off the air intake box.
Airaid PowerAid Custom Throttle Body Spacer Installation - 2012 Jeep Grand Cherokee
All right, today on this 2012 Jeep Grand Cherokee we're going to install part number AR300-637 from Airaid. This is a PowerAid throttle body spacer. OK, first thing we need to do is go ahead and lift up on the engine cover and move it out of the way. It simply just pops up. Next we need to disconnect the air temperature sensor from the air intake, it's just forward of the throttle body, on the passenger side. Then next, we'll go ahead and loosen the clamp on the intake tube going toward the throttle body. We'll pull up on the center of the intake tube and pop it loose.
AIRAID CAD Air Intake System Installation - 2006 Chrysler 300C
Today is a 2006, Chrysler 300C. We're going to install part number Ar350-199 from AIRAID. To start off our install, we're going to go ahead and disconnect the negative cable from the battery located in the trunk. Next we need to loosen the hose clamp that holds the factory intake tube to the throttle body. Next, we'll go ahead and disconnect the breather hose from the factory air box lid. Then we'll go ahead and remove the lid to the air box. We'll pull both lock down tabs towards the front.
AIRAID PowerAid Throttle Body Spacer Installation - 2006 Chrysler 300C
Today on our 2006 Chrysler 300c were going to install part #: AR350-532, this is the Power Aid throttle body spacer. To start off our install were going to go ahead and remove the negative battery cable. Now well go ahead and remove the air intake assembly. Well unsnap the air box, then well go over to our clamp on the throttle body. Well go ahead and loosen up that clamp and theres a small chamber off to the left hand side that you can pop off from its rubber fitting. Then we can go ahead and take the unit off as one piece.
AIRAID PowerAid Throttle Body Spacer Installation - 2012 Toyota 4Runner
Today on our 2012 Toyota 4Rrunner, were going to install Part Number AR510-628 from Airaid. This is the Power Aid Throttle Body Spacer. To install our part were going to have to get underneath the hood. First thing were going to do, well go ahead and remove the negative terminal from the battery. Then well go ahead and remove the engine cover, the plastic compartment on top we simply pull up and then pull away from the hinge. Go ahead and set it aside for now.
Subscribe to email newsletter
privacy - we don't send unsolicited email
All images, layout and content copyright etrailer.com