MagnaFlow Exhaust Installation - 2007 Ford F-250 Super Duty - Video
Today on this 2007 Ford F-250 Super Duty we will be installing MagnaFlow performance exhaust part number MF16926. You need to do a couple of things in preparation before we get started installing our exhaust system. First we want to disconnect the vehicles battery. This will allow the computer to reset itself once we get the new system in place and that will help prevent electrical accidents. If your vehicle has four wheel drive we also need to go ahead and remove the transfer case rock shield. There are four bolts holding it on two per side. We will just set that off to the side for the time being. We also need to go ahead and remove the lower bolt from the rear passenger side shock. Again this will allow us to swing the shock out of the way to help make the removal of the system easier. 00:54 more
Watch Video
Posted: 1/13/2010 3:08:26 PM
MagnaFlow Exhaust Installation - 2007 Ford F-150 - Video
Today on a 2007 Ford F-150 we will be installing a MagnaFlow performance exhaust, part number MF16523. Our first procedure is going to be soaking down our clamp and hardware. I highly recommend that you soak this down several times and let it sit for at least 30 minutes before trying to break this nut loose. These bolts tend to become extremely rusted and very difficult to remove. As you can see, we have already gotten this nut broken loose. This clamp is loose but, if it becomes difficult to back off, I recommend that you work the nut back and forth, on and off, breaking free the rust that has built up in the threads of the clamp. After giving it a few taps with the hammer, you will notice that the clamp came loose and broke the rust free. Now that my clamp is loose, I just want to spread it open a little bit to make it easier to remove the exhaust pipe. 0:58 more
Watch Video
Posted: 5/2/2011 3:55:40 PM
MagnaFlow Exhaust Installation - 2002 Ford F-350 Super Duty - Video
Install-exhaust-2002-ford-f350-mf15979 Today, were working on the 2002 Ford F350 Super Duty. Were going to install the MagnaFlow performance exhaust part number MF15979. Before we can install our new exhaust we have to remove the old exhaust, so Im going to take a little spray lubricant, spray each one of the rubber hangers, make it a little easier to remove and reinstall later. We also see there some exhaust clamps that were going to need to be removed. Were going to thoroughly spay these down with some penetrating oil to make it a little easier to break them free and get them loose. Alright start removing the exhaust; were going to come up here to the turbo underneath the hood. more
Watch Video
Posted: 12/19/2011 4:30:30 PM
MagnaFlow Exhaust Installation - 2001 Ford Ranger - Video
Today on this 2001 Ford Ranger we are going to install part number MF15679 from MagnaFlow. The first thing we are going to do to get ready is go ahead and move the spare tire. You do not have to do that but it makes things a lot easier to get to and see. The next thing we are going to do is spray down the bolts going towards the catalytic converter. Let it sit for awhile and we will go ahead and loosen them up. And also, you will notice, this is not the original factory connection going to the catalytic converter too. This is actually another aftermarket exhaust. We will leave that set for now. Now we will go back to the rest of the exhaust and remove all of the rubber hangers. Just spray them down with some lubricant also and pull them apart. Alright, we will just push it to one side and pull it out. And then we will pull out the other side. You should be able to pull it all out as one piece. 0:56 more
Watch Video
Posted: 3/16/2011 10:04:26 AM
MagnaFlow Exhaust Installation - 2007 Ford Mustang Shelby GT500 - Video
Today on this 2007 Ford Mustang Shelby GT500 we are going to be installing Magnaflow Exhaust system part number MF16674. The Magnaflow exhaust system is going to allow us to replace our factory exhaust from just rearward catalytic converters all the way to the exhaust tips. First thing we are going to need to do is remove the stock system. more
Watch Video
Posted: 11/15/2010 11:34:05 AM
MagnaFlow Exhaust Review - 2004 Mustang Cobra - Video
Rev up your engines! Were going to give you an overview of the MagnaFlow Stainless Steel Cat-back exhaust system and what it can do for your vehicle. This dual exhaust system not only improves engine performance by increasing horsepower, torque, and fuel efficiency but also decreases exhaust gas temperature. The sleek stainless steel design was engineered with mandrel bent tubes. These tubes have the same diameter throughout the system ensuring a constant uninterrupted airflow decreasing exhaust turbulence. MagnaFlows intelligently designed mufflers are created with a layer of steel wool insertion that absorbs noise but still allows for the signature deep, throaty sound to let people know you are riding on a MagnaFlow. more
Watch Video
Posted: 12/14/2009 6:15:42 AM
