Trailer Wiring Harness Installation -2010 Subaru Outback Wagon - Video
Today on this 2010 Subaru Outback Wagon we are going to be installing wiring harness part number 118467. We are in the rear cargo area of the Outback Wagon, we want to go ahead and locate the ports that our wiring harness will be plugging into. This port is open ended and located behind the interior panel here on the drivers side of the vehicle up on the forward side, near the tow hook. :24 more
Watch Video
Posted: 5/13/2010 3:08:20 AM
Trailer Wiring Harness Installation - 2010 Subaru Outback - Video
Alright, today on this 2010 Subaru Outback, we are going to install part number 118467 from Tow Ready. OK, the first thing that we need to do is get in the back of the vehicle. We need to open the trunk area. Alright, we will take out the floor panels. Start with this cover here. Now we have to take out the Styrofoam parts too. And we are going to work our way down to the sheet metal here. And then we are going to remove this piece of Styrofoam here, There are a couple of little plastic rivets. 0:51 more
Watch Video
Posted: 7/9/2010 8:55:27 AM
Trailer Wiring Harness Installation - 2001 Subaru Outback Wagon - Video
Today on this 2001 Subaru Outback Wagon we are going to be installing part number 118461 from Tow Ready. The first thing we are going to do is get inside the trunk and locate our factory towing harness kit. In the instructions it does state that it is located on the driver side of the vehicle, but on some yours it can be on the alternate side. As you can see we found our plug in. :26 more
Watch Video
Posted: 6/24/2010 1:57:28 AM
Trailer Wiring Harness Installation - 2007 Subaru Outback Wagon - Video
Today on this 2007 Subaru Outback we are going to install part number 118461 from Tow Ready, this is their T-One wiring harness. The first thing we need to do is get access to the inside of the vehicle. We are going to hold up the hatch and remove the floor coverings. We want to get down to the sheet metal by the spare tire. This panel will pop up and we are going to do both sides because on the wire in these vehicles they can be on the driver side or passenger side so it is best to take everything apart and look for it. We are going to remove these parts here and we are going to take our trim panel tool and just pop it from the bottom. There is one more in the corner down here too. Lets repeat for the other side of the vehicle. 00:58 more
Watch Video
Posted: 9/27/2010 2:31:26 PM
Trailer Wiring Harness Installation - 2009 Subaru Forester - Video
Today on this 2009 Subaru Forester we are going to be installing wiring harness part number 118467. We are at the rear of the vehicle and the port that we are going to need to plug our wiring harness into is located inside the cargo area underneath the floor board over here on the driver side of the vehicle. We are going to need to remove quite a few pieces to gain access to the port. The driver side styrofoam has a few retaining fasteners holding it in to position. To remove those you can either use a flat headed screwdriver or you could use a rivet removal tool. 00:33 more
Watch Video
Posted: 7/6/2010 7:51:54 AM
Trailer Wiring Harness Installation - 2006 Subaru Outback Wagon - Video
Today on this 2006 Subaru Outback Wagon we will be installing sequent wiring harness part number 118461. We are in the rear cargo area of the Outback Wagon and we are going to locate the wiring port that our harness is going to plug in to. The port on this particular vehicle is going to be located directly behind the driver side panel nearest the tail light. To gain access to that we are going to need to remove a few pieces of the interior. As you can see I have already removed the spare tire and the flooring. But we will also need to remove the rear threshold section and the styrofoam flooring piece which has one push pin here and two clips at the forward side. 00:38 more
Watch Video
Posted: 3/19/2010 5:41:45 AM
Trailer Wiring Harness Installation - 2009 Subaru Forester - Video
Okay, today on our 2009 Subaru Forester we are going to install part number 118467 from Tow Ready. Okay, the first thing we need to do when we install our wire harness is get down to the spare tire area, so we are going to take off this mat here get it out of our way. Take out the foam s. We will take this out of our way, and we will remove the net. Okay, and then this foam section here also has to come out. :31 more
Watch Video
Posted: 12/30/2009 7:57:45 AM
Trailer Wiring Harness Installation - 2004 Subaru Forester - Video
All you have to do is get to the inside panel and get to the connector. Basically we have to take out this panel, and this panel to get the spare tire well and we can find our panel that way. Once you get to the spare tire well you should see this connector wrapped in blue tape. Your T-connector will plug right in to that and well go ahead and make a permanent mounting. We can route this back here and make sure you have enough wire coming out. After that go ahead and stick it down with the adhesive. more
Watch Video
Posted: 8/8/2008 4:04:26 AM
Trailer Wiring Harness Installation - 2011 Subaru Forester - Video
Today working on a 2011 Subaru Forester, were going to install a Tow-Ready T-One Connector part# 118467. Go ahead and remove the cargo cover, were going to remove the center foam tray and the driver's side foam tray to access the wiring underneath. And you see it gives us access to the manufacturer's trailer wiring. Now we can take our new Tow-Ready Connector and plug it into the manufacturers connection port. With our port connected we need to mount our converter box, we'll peel back the cover of the two-side adhesive and mount it to the sheet metal. Were mounting it to the sheet metal make sure you've got a good flat clean surface. more
Watch Video
Posted: 1/26/2012 4:03:00 PM
Trailer Wiring Harness Installation - 2011 Subaru Legacy - Video
Today on this 2011 Subaru Legacy we are going to install part number 56091 from Curt. The first thing we need to do is get into the trunk area and remove some of the interior components. We get down to the spare tire and remove the threshold as well. Alright there is 3 plastic rivets we have to remove. We just pull straight up on it, it comes right out. To remove this tie down loop, turn it, one quarter turn, there is a tab on the inside you can push down with a screwdriver and then you can work it out. more
Watch Video
Posted: 12/11/2011 4:03:15 PM
Trailer Wiring Harness Installation - 2010 Subaru Forester - Video
Today on this 2010 Subaru Forester we are going to be installing wiring harness part number 118467. We are in the rear cargo area of the Forester and we want to locate the port that we are going to be plugging our wiring harness into. This port is located underneath the cargo floor over on the driver side of the vehicle. We are going to need to remove a few pieces before we can get started. We obviously need to remove the covering not only in the center section but on the driver side as well. Then we need to remove the styrofoam storage bin on both the center and driver side sections as well. For the driver side compartment there is actually two push pins that are holding it into position. 00:29 more
Watch Video
Posted: 6/4/2010 7:06:54 AM
Trailer Wiring Harness Installation - 2001 Subaru Forester - Video
Today we are going to install part number 118461 from Tow Ready, and we are going to install this part on a 2001 Subaru Forester. The connection points are inside the vehicle, in the rear, so we have to get inside the rear hatch and start pulling up the floor panels. Our connection point happens to be right here, underneath the threshold on the passengers side. You just pull it out. It has got the blue tape on it. And our T-connector will simply just snap in place, like so. And all that remains is to go ahead and attach the Modulite to the back of the sheet metal here. You can put it just any place you want but it seems pretty convenient and out of the way right here. And we can zip-tie our wires to the existing wire package here, and they will be safe and out of the way. Now we did not really have to take out the spare tire, but it gives you a better idea of what is going on. more
Watch Video
Posted: 6/5/2009 9:25:23 AM
Trailer Wiring Harness Installation - 2007 Subaru Forester - Video
Today we are going to install part number 118461, we will be using this on a 2007 Subaru Forester. The first step involved with installing is taking off some of the interior panels and getting down to the floor. So we have to get down to the bottom where we can see the wiring and well trace it back to find the connector. This panel comes off first, followed by the panel underneath, and then this panel comes up. Now we have gotten to our wire harness, now we need to find the connector. Once we find our harness, well follow that back to the tail light as the instructions say, you look around and here is the plug right here. As a note this plug can be found on different models and years possibly further up here towards the front. You could also find them on the other side, just check the instructions before you start. more
Watch Video
Posted: 10/23/2008 12:05:00 PM
