Trailer Wiring Harness Installation - 2008 Chrysler Town and Country - Video
Today on this 2008 Chrysler Town and Country we will be installing part number 118552 from Tow Ready. The first step involved is to open the rear hatch so we can remove the tail lights and get to our connections. We have to remove these two screws here and here. With the driver side done, we will repeat this process on the passenger side. When pulling the lights, gently rock them back and fourth to loosen up the push pins, then pull out. :28 more
Watch Video
Posted: 6/9/2011 9:49:33 AM
Trailer Wiring Harness Installation - 2007 Chrysler Town and Country - Video
Today on this 2007 Chrysler Town and Country we are going to install part number 118300 from Tow Ready. First open up the back hatch of the vehicle and disconnect the tail lights. To take off the tail lights what we need to do is pull out these two plastic rivets right here. Swing it out and it pops right out. To disconnect the wire harness we have to push in this red tab right here so it unlocks. Push down at the top of the wire harness and it should come right apart. Repeat the same process on the passenger side. Next we are going to pull out this grommet right here and we are going to make a slit in it so we can run our new harness back through here. We are going to leave it like that for now. Repeat the same thing on the other side. 00:47 more
Watch Video
Posted: 3/31/2010 1:33:39 PM
Trailer Wiring Harness Installation - 2007 Chrysler Pacifica - Video
Today we are going to be installing wiring harness part number 118303 on a 2007 Chrysler Pacifica. Okay, we are at the rear of the vehicle, and we are going to go ahead and locate the attaching points for our wiring harness. The attaching points are actually located directly behind the tail lights. So the first thing we need to do is go ahead and remove both of those. To do that, we just need to remove the two screws here on the inboard side, and then we will just pull the tail light assembly away. more
Watch Video
Posted: 4/29/2009 6:14:40 AM
Trailer Wiring Harness Installation - 2003 Chrysler Pacifica - Video
Today we are going to install part number 118303 from Tow Ready. We are going to install this on a 2003 Chrysler Pacifica. Our first step is to go ahead and open up the tailgate and then remove the tail lights from the vehicle. These tabs can be loosened up and then we disconnect the tail light. Then go ahead and repeat for the other side. Next what we have to get to is the power lead for the wireless harness. That is hidden behind the grommet here. It is this red wire right here. We are going to run the connector from the inside and put a simple slit in the grommet here that way. Then you may go ahead and put a slit in the grommet. Then we go ahead and put our wiring the passenger side and it down behind the bumper in the body. Just let that go all the way through. We will route that on the bottom of the vehicle to the other side. We will also put the 4 pole down into and through the body as well. Then we will go ahead and hook up our power lead. Now we hook up our connectors like the one between the tail light and the wiring harness. Then go ahead and connect the tail light. Push those red tabs so that they lock back into place. more
Watch Video
Posted: 8/8/2008 4:47:20 AM
Trailer Wiring Harness Installation - 2004 Chrysler PT Cruiser - Video
Watch Video
Posted: 1/11/2012 3:21:17 PM
Trailer Wiring Harness Installation - 2002 Chrysler Town and Country - Video
Watch Video
Posted: 12/19/2011 4:16:18 PM
Trailer Wiring Harness Installation - 2005 Chrysler Pacifica - Video
Today on this 2005 Chrysler Pacifica, were going to be installing wiring harness part 118303. Were going to first go ahead and locate the ports that were going to be plugging our wiring harness into. Now these ports are located directly behind the tail lights on both sides of the vehicle, so were going to go ahead and remove each one of the tail lights. To do that you can see we have opened up our cargo door here to access the fasteners here on the inboard side, just go ahead and remove those and we can pop the tail light right off. If you turn the tail light over here, right here at the bottom is the connector were going to be using, you want to go ahead and separate the two pieces first. To do that we want to go ahead and slide the red locking tab over first and then go ahead and press the release button here at the top and pull the two pieces apart. We can set the tail light off to the side for the time being and go ahead and do that for the passenger side as well. We are going to continue over here on the drivers side, and pull the grommet away from the vehicle. This wiring is actually a powered unit and when we pull the grommet away we actually have an existing power wire that were going to use. If you follow the tape forward here you can see there is a red wire here that is taped off and if you cut that back, there is a connector on there and were going to go ahead and use that. more
Watch Video
Posted: 12/8/2011 2:28:48 AM
Trailer Wiring Harness Installation- 2006 Chrysler 300C - Video
Today we will be working on a 2006 Chrysler 300C. We will be installing Tow Ready T-One connector part number 118406. First, we are going to access the rear trunk. Okay located behind the tail lights of the vehicle, the plastic wing nut we are going to remove. I am going to open the spare tire and battery cover. I am going to repeat the same process by removing the plastic wing nut on the drivers side. Now we will pull the carpet back and you can see we have access to the tail light wiring. We will be making our connections here, a little bit later on. Now what I want to do is remove this rear carpeting and take the carpeting out and put it away for now. We will be reinstalling that later. 1:02 more
Watch Video
Posted: 8/2/2011 12:06:21 PM
Trailer Wiring Harness Installation- 2005 Chrysler Pacifica - Video
Today on this 2005 Chrysler Pacifica we are going to install Tow Ready T-One connector part number 118303. First, we are going to open the tailgate so we can access the mounting bolts for the drivers side tail light lens. We are going to remove these two mounting bolts here. Now that we have the two mounting screws removed we are going to remove the tail light assembly. Be careful not to break the alignment tabs that are still connected. As you can see here, it gives us access to the rear tail light wiring. Now that we have the lens assembly away from the vehicle, we need to locate this red wire connector which will be attached to the manufacturers wiring harness. We are going to pull it up and out of the vehicle and connect our new Tow Ready T-One harness to it. Then, we will slide the locking tab into place. 1:02 more
Watch Video
Posted: 7/29/2011 9:34:58 AM
Trailer Wiring Harness Installation - 2010 Chrysler Town and Country - Video
Today on this 2010 Chrysler Town and Country we are going to be installing wiring harness part number 118552. We are at the rear of the Town and Country and the first thing we want to do is go ahead and locate the ports that we are going to be plugging our wiring harness into. These ports are going to be located directly behind the taillight assembly on both the driver and passenger sides. So the first thing we want to do is go ahead and remove both of those taillight assemblies. To do that, you can see we have opened up the cargo door here. And if you look at the inboard side of the taillights, we have two screws holding the taillight into place. With those two screws removed, we can take and we want to rock the taillight assembly back and forth a little bit because there are some outboard side clips holding it into position still. OK, with the taillight pulled back here, for clarity purposes I am going to go ahead and disconnect the taillight assembly and set it off to the side. And to do that, I am just going to go ahead and release the connectors. To do that, you can see on the bottom side of each one there is a red tab. If you take and pull that back that releases the clip. And then there is a button here on the top. Press that in and that will separate the two pieces. 1:03 more
Watch Video
Posted: 4/22/2011 7:50:53 AM
Wiring Harness Installation - 2009 Chrysler Aspen - Video
Today on this 2009 Chrysler Aspen we are going to install part number 118390 from Tow Ready. This is their modulite wiring harness. The first thing we need to do is open up the back hatch of the vehicle and get to the fasteners that hold the lights in place. We are going to remove the taillights as our first step. These just have plastic fasteners that you just remove. When you pull these off, you want to kind of pull them off to the side a little bit and pull back a little bit. We can go ahead and disconnect this light for now. Just push in this red tab right here and push down this button and it comes apart. We have our driver side off. Let us go ahead and do the same thing with the passenger side. Next we are going to take our wire harness and we are going to the 4-pole end down behind the bumper, towards the ground for now. And then the lead with the red, yellow and brown wires, we are going to hook up to the wiring harness that was going into the taillight. Next we will take our white and green wire and do the same thing like we did with the 4-pole wire. Drop it behind the bumper and out of our way. 1:01 more
Watch Video
Posted: 3/14/2011 11:19:42 AM
Trailer Wiring Harness Installation - 2004 Chrysler Town and Country - Video
Today on this 2004 Chrysler Town and Country we are going to be installing wiring harness part number 118300. We are in the rear cargo area of the Town and Country and we are going to locate the ports that we are going to be plugging the wiring harnesses into. The ports for the harness are located directly behind the tail lights on both the driver and passenger sides of the vehicle. However the harness itself is going to be routed and stored inside the vehicle so we are going to start the install on the inside of the vehicle and remove some of the interior paneling. 00:31 more
Watch Video
Posted: 1/28/2011 3:37:33 AM
Trailer Wiring Harness Installation - 2008 Chrysler Aspen - Video
Today on this 2008 Chrysler Aspen we will be installing part number 118390 from Tow Ready. This is a T-One wiring connector. To begin our install we need to open up the hatch to get to the plastic rivets that holds the tail lights in place. The tail lights have to come off because our wiring connections are behind the tail light themselves. more
Watch Video
Posted: 9/24/2009 10:16:59 AM
Trailer Wiring Harness Installation - 2003 Chrysler Town and Country - Video
Today on this 2003 Chrysler Town and Country we are going to install 118376 from Tow Ready. Our connection point is actually behind the taillight on the driver side. We are going to go ahead and take out these two plastic rivets, make our connections, then run our 4-pull to the inside of the vehicle, and it will be stored in the jack storage compartment when we are not using it. more
Watch Video
Posted: 8/31/2009 7:00:11 AM
Trailer Wiring Harness Installation - 1997 Chrysler Concorde - Video
Today we are going to be installing wiring harness part number 119175 on a 1997 Chrysler Concorde. OK, we are inside the trunk area here, and as you can see, I have gone ahead and removed the rear carpeting to expose the wires that we are going to be tapping into to wire the wiring harness. We can go ahead and access most of the wires directly right here in this area. The first thing we want to do is to go ahead and probe the wires to determine which function each wire carries. The first thing we want to do is to test for our left-turn signal. And it appears to be this light green wire coming directly out of the harness. Then we want to find our right-turn signal, which appears to be the tan wire that is feeding over to the passengers side. Then we want to find the brake line, which again appears to be the white wire with the tan stripe. And then the last thing we need to find is our running lights, and that appears to be the black wire with the yellow stripe. Then on our harness here, we are just going to go ahead and make our connections to the wires that we just found. The yellow wire is going to be our left-turn signal wire. The white is, again, going to be the ground, which we want to use that common grounding point right over here. The brown wire was our running-light feed, the red wire was our brake feed, and our green wire is our right-turn feed. more
Watch Video
Posted: 4/1/2009 11:10:45 AM
Trailer Wiring Harness Installation - 2007 Chrysler 300C - Video
Today we are going to install part number 28406 from Tow Ready. We are going to install this on a 2007 Chrysler 300C. The first step we have to do is get into a trunk area. Then we need to take off these wing nuts to take out this carpeting and expose the wiring that we need to get to. We need to do that on both sides. There is a little plastic fastener that would help for it to come apart too. There is the wiring we need to get to right there. Now pull back this trunk panel right here, exposing the battery and spare tire. Then we will take the wing nut on the other side and get to the wiring there too. Lastly we are going to take off this interior panel right here. Starting on our driver side, we will go ahead and disconnect here and install our T-connector. Simply push this red button out the way, press on the end, and it comes right apart. more
Watch Video
Posted: 8/7/2008 10:52:02 PM
Trailer Wiring Harness Installation - 2007 Chrysler 300 Touring Edition - Video
First thing we need to do is access the trunk area. Lift up the back flap here and remove the rear threshold piece, there are four pop rivets holding it in place. We pull back the threshold on the passenger side, it will reveal the connection point for the wiring harness. Once we locate the connection point we want to flip back this red tab, which is holding it in place, and push the button down on the topside and pull the connectors apart. This time we want to take the t wiring harness and plug it into this. more
Watch Video
Posted: 8/8/2008 4:26:08 AM
