Texas Flag Trailer Hitch Cover Review - Video

Today we are going to show you the state of Texas Flag 2-Inch Receiver Hitch Cover, part number 034092101109. As you can see here, the tube cover itself is a depiction of the Texas flag. And this is an alloy material with enamel that has been put inlay into the shape itself. I will show you the back side of it. This comes with a foam gasket to help it fit on the receiver hitch a little bit tighter. It also comes with two different wire forms here. These wire forms adjust the tube cover to match different variants in the hitch pin. Some are farther back in the hitch tube than others. As you can see, there is only a short length here and a long length here. And you only use one at a time and they fit into these tabs sticking out. The tabs themselves have different lengths where the holes are. This tab here, if you can see, is towards the edge. And on this one over here, it is a little bit closer down towards the bottom. Use that in conjunction with the wire forms to get the best fit possible on your hitch. more

Watch Video

Posted: 12/1/2008 5:30:56 PM

Soccer Ball Trailer Hitch Cover Review - Video

Alright, today we are going to show you part number CR-404 from Bully. This is their soccer ball for your trailer hitch cover. As you can see, this shows basically half of a soccer ball. And it is a pretty good sized tube cover. It is 6-inches in diameter, so you may want to take into account what you hitch and bumper edge relation is like to make sure you have enough clearance for it. Basically, from the top of the cover down to the tube itself is going to be about 2-inches, so you might want to double check that measurement. more

Watch Video

Posted: 11/28/2008 4:53:09 PM

Golf Club and Lock Trailer Hitch Cover Review - Video

Today we are going o be showing you part number CR-418. This is the Golf Club Stainless Steel Trailer Hitch Cover with an accompanying lock. Now, this fits both an 1-/14 and 2 inch hitches and it also has great random bushings to fir your hitch better. It also comes with its own lock to insure it is secure as you are traveling, to make sure nobody walks off with it. It is constructed from a rust proof stainless steel and includes a hitch pin and lock. It is designed to fit both an 1-1/4 and 2-inch trailer hitches. And the hitch cover face is 8 inches wide by 4 inches tall. This is for anybody that is a big fan of golf, who likes to show it off as you drive. more

Watch Video

Posted: 11/28/2008 4:23:28 PM

Brake Light Trailer Hitch Cover Review - Video

Today we are going to cover part number CR-007 from Bully. This is the Brake Light Trailer Hitch Receiver Cover for 2-inch receivers. This is your most basic lighted trailer hitch cover out there. It fits a 2-inch receiver only, and it has basically a red light in the back here that comes on when you hit your brake or your right-turn signal. And that is the only time it comes on. Again, it is a very basic unit. But it is always good to have an extra third brake light just for safety's sake. We will go ahead and install it on a vehicle and show you how it looks. more

Watch Video

Posted: 11/28/2008 9:12:54 AM

Waving American Flag Trailer Hitch Cover Review - Video

Today we are going to show you an American Flag Waving 2-Inch Hitch Receiver Cover, from Alfred. And this is part number 034092100201. As you can see here, it depicts an American flag in a waving position. And this fits only 2-inch receiver hitches. And it is constructed out of alloy material with an enamel inlay into the etching here to provide the colors. On the backside here, you can see the actual alloy material that it is made out of. It also comes with a gasket. What that does, it helps seal up the hitch tube cover and also provides a little bit of friction or something to press against for the wire forms as they are installed into the receiver hitch itself. And the wire forms themselves have two different lengths to facilitate installing a hitch cover, because sometimes a hitch pin in the end of the hitch itself has varying lengths, depending on that manufacturer. And on the tabs here, you can see that the pins have different heights, like say this one is towards the end and this one is towards the bottom. Again, it gives you better adjustment to make a proper fit on your hitch. more

Watch Video

Posted: 11/26/2008 6:01:26 PM

Happy Face Brake Light Trailer Hitch Cover Review - Video

Today we are going to show you part number CR-007H from Bully. This is their Happy Face Brake Light Trailer Hitch Receiver Cover for 2-inch trailer hitches. This is designed for off-road use only, so it could be pretty good for a show vehicle, possibly. We will go ahead and plug it into a typical receiver hitch and show you how it looks. more

Watch Video

Posted: 11/26/2008 5:47:51 PM

Dale Earnhardt Jr. Number 8 NASCAR Chrome Trailer Hitch Cover Review - Video

Today we are going to show you part number CRN-8 from Bully. This is the Dale Earnhardt, Jr., Number 8 NASCAR Chrome Trailer Hitch Receiver Cover. The material that this tube cover is made out of is die-cast material, chrome, with Dale Earnhardt, Jr.s insignia Number 8 on there. This product will fit 2-inch and 1-1/4 inch receiver hitches. These pieces right here are what make it fit into a 1-1/4 inch receiver hitch. It also comes with a foam gasket to help give it a tight fit into the hitch. And on the tube cover itself, we have this one set up for a 2-inch receiver hitch, as you can see right here: the two plastic parts that go into the 2-inch part, and the foam gasket also. more

Watch Video

Posted: 11/26/2008 5:45:45 PM

Propeller Trailer Hitch Cover Review - Video

Today we are going to show you part number CR-402L from Bully. This is their 4-Blade Propeller Trailer Hitch Cover for 1-1/4 and 2 inch trailer hitches. It also has an LED stoplight on the back also. As you can see here, it is a 4-blade propeller and it spins freely in the wind. It is pretty neat. When you go down the road, it spins around and you look like you have a propeller on the back of your vehicle. And you can see, off to the side there are two other plastic parts. Those are parts that will allow you to use it in an 1-1/4 inch receiver hitch also. The foam gasket on the side helps make it a tight fit whenever possible and also helps keep out extra dust and corrosion from getting inside the hitch itself. more

Watch Video

Posted: 11/26/2008 5:39:47 PM

Maltese Chrome Trailer Hitch Cover Review - Video

Today we are going to cover part number CR-414, from Bully. And this is their Maltese Chrome Trailer Hitch Receiver Cover. This cover here, as you can see, has a Maltese cross and it works on 1-1/4 and 2 inch receiver hitches. This consists of die-cast construction with a chrome finish and it has plastic parts in the back to fit either 1-1/4 or 2 inch receiver. Off to the side here, we do have the pieces right here that do make it adaptable to an 1-1/4 inch receiver and a foam gasket. And the cross itself, we have a 2 inch version mounted up, with the plastic here and the foam gasket installed. more

Watch Video

Posted: 11/26/2008 5:21:19 PM

Harley-Davidson Trailer Hitch Cover Review - Video

Today we are going to show you the Harley-Davidson Trailer Hitch Cover, and this part number is HDHCY12. This is a high-end trailer hitch cover for your vehicle. It features embedded jewelry-quality cubic zirconium stones, as you can see, outlined around the edge of the emblem. This has been lab tested for weather- and corrosion-resistant construction. The post of this tube cover is made of stainless steel, and the face of it is chrome-plated solid brass. This tube cover also comes with various components to install on your vehicle for a perfect fit. We will get this tube cover ready to install. We will just take it out of the packaging here and flip it around. And these are the bushings. Again, you will use them according to your vehicle. We are going to use the thickest one, and it slides on in place, and then we will use the smallest one on top of it. And it uses any combination as long as it makes a nice, tight fit into your hitch. more

Watch Video

Posted: 11/21/2008 5:44:17 PM

Tailgater Trailer Hitch Cover Review - Video

Today we are going to show you part number 40171BLK from Alfred Hitch Cover. What we have here is the Official Tailgater hitch cover. It is a great little device, a perfect addition to any tailgating event. It is a pretty simple design. It installs into a 2-inch receiver clip. Use your standard pin and clip or locking pin and clip, and you can use it as a bottle opener. As you can see here we have the Official Tailgater and we also have this wire form here. And the wire form actually helps it stay in place. And you see it also has a foam gasket and another wire form installed. There are two different styles wire forms - depending on the hitch pin and the distance to the end of the hitch. It varies from manufacturers. more

Watch Video

Posted: 9/19/2008 1:17:18 PM

DWD Plastics Duck Trailer Hitch Cover for 2 Inch Receivers Review - Video

As you can see this part has a hunting theme to it for all you hunters out there. Well show you how this installs to the receiver hitch of your vehicle. As you can see it has a little spring clip in here, you simply push it together a little bit, and it slides right into your hitch. Once you have it started you simply push it all the way back and it locks into place. When you take it off you just push it in and pull it out, its a relatively simple device. What else you can do with this is replace the clip inside here with a deadbolt receiver lock, any 2 inch variety will work fine on this model. Its just a little extra security so no one walks off with it. There you have it for part # 202040, the duck hitch cover from DWD plastics. more

Watch Video

Posted: 7/28/2008 1:14:24 PM

Harley Davidson LED Hitch Cover Review - Video

As you can see this product has the Harley Davidson logo with the base orange color. It does light up orange when you hit the running lights, and lights up red when you hit the brakes. It is all stainless steel construction except for the lens cover of course. Well install one on the pickup truck we have here and show you how it works. As you can see it comes with three foam gaskets that adjust the tension of the hitch in relation to the tube cover. You can use a thicker bushing to push the tube cover into hitch to make for a nice snug fit or if you need less you have thinner ones for that. Also it comes with two tools, theyre specialized tools to tighten the bolt into place. Theyre not a conventional socket by any means, so really this means its anti-theft. Basically without these tools you cant take it off, and again the bolt itself is stainless steel. more

Watch Video

Posted: 8/7/2008 4:50:16 PM