This Old Boat Trailer: Master Cylinder Installation - Video
Today on This Old Boat Trailer we are going to rebuild the hydraulic actuator on here and we are going to be using part number 85841, the master cylinder itself, and then we are going to use a master cylinder replacement cap part number A87478, and the cable push rod replacement kit part number 85852, all from Atwood. The first thing we need to do is remove the old master cylinder itself. This is going to require taking off the cap which we have already done. We have disconnected the line back here already and then we can see our factory line, lets disconnect that and then we are just going to undo these four bolts right here. There is probably going to be some leftover brake fluid in there so it will be a good idea to wear some gloves or something. We are going to pull out the back and then underneath there is a little push rod you may want to pull away from it too to help knock it out. 01:09 more
Watch Video
Posted: 9/1/2010 5:26:32 AM
This Old Trailer: Installation of a Trailer Coupler - Video
Today on This Old Trailer we are going to install a brand new coupler using part number 2836AT from Master Lock. This is going to be a three inch wide coupler on it and in between here is going to be three inches wide and it is going to use a two inch ball. The first steps involved are to remove the old coupler. It has been on there for awhile. It is rusted so take a couple of wrenches to it and maybe we will get lucky and we will actually break the bolts and get it to come loose that way. This little stand right here got bent back, probably pinching the coupler, so we are going to take that one apart too. Obviously this is rusted in place so we are going to have to persuade it off. 00:59 more
Watch Video
Posted: 3/31/2010 11:10:08 AM
Titan Trailer Coupler T4853100 Review - Video
Today were going to do a review on part number T4853100. A Titan Zinc-plated Coupler to fit 3-inch straight tongue couplers will also fit the current model Titan 10 and 20 act weighters. This coupler uses a trigger-style latch. It is of a zinc-plating which is a corrosion resistant. It has a durable steel construction. It will fit on a ball size of 2 in 5, 16s. more
Watch Video
Posted: 1/25/2012 6:02:24 PM
Titan Trailer Coupler T2343400 Review - Video
Today were going to review part number T2343400. A Titan Prime Coupler is a multi-fit ball coupler that fits on a 3-inch channel to bolt on coupler. This coupler uses an easy turn wheel latch system that you push this lever down and you can turn it to tighten it up and this will adjust the fit one in 7, 8-inch, 2-inch, and 15 no meter hitch balls. This is durable steel construction. It is a bolt-on installation. Couple measurements I will give you, the width would be fits on a 3-inch channel; another measurement is the distance between the mounting holes on the side. more
Watch Video
Posted: 1/25/2012 6:02:18 PM
Fulton Trailer Coupler F346000301 Review - Video
Today, we're going to review part number F346000301, the Fulton Fas-Lok Coupler with a Cast Ball Clamp, fits a 2" hitch ball and will fit on a 3" channel. This coupler is a trigger latch style. This is a bolt on coupler. It has a Z-Max 600 finish, which offers superior corrosion resistance. It is designed to fit a 2" hitch ball. And do couple measurements, measures 3", so it will fit a 3" channel. more
Watch Video
Posted: 1/25/2012 6:02:11 PM
Fulton Trailer Coupler F343000301 Review - Video
Today, we're going to review part number F343000301, the Fulton Fas-Lok Coupler for a 2" hitch ball, fits a 3" channel coupler, fits a 3" trailer channel. This is a trigger-style latch design. It is a bolt on coupler, has a Z-Max 600 finish, which offers superior corrosion resistance. Fits a 2" hitch ball size. Couple measurements, 3" for the channel, another measurement is the distance between the side-mounting holes. We measure that center-to-center would be 3". more
Watch Video
Posted: 1/25/2012 6:02:06 PM
Fulton Trailer Coupler F222500301 Review - Video
Today we're going to do a review of part number F222500301, the Fulton Fas-Lok Coupler for a 2" Hitch Ball that will fit on a 2-1/2" Channel. This coupler uses the Fas-Lok trigger-style latch that makes for a quick and easy trailer hookup. It has a Z-Max 600 finish, which offers a superior corrosion resistance. And is designed to fit a 2" hitch ball and on a 2-1/2" wide channel. I'll just do a quick measurement here. Measurement on your channel would be on the inside, which measures 2-1/2". more
Watch Video
Posted: 1/25/2012 6:02:00 PM
Fulton Trailer Coupler F222000301 Review - Video
Today, we're going to do a review on part number F222000301, the Fulton Fas-Lok Trailer Coupler design to fit a 2" hitch ball, fits on a 2" channel. This coupler is a trigger latch style. It has a Z-Max 600 finish. It offers superior corrosion resistance. It does fit a hitch ball size of 2". The channel, we'll measure that it fits on is 2" wide. more
Watch Video
Posted: 1/25/2012 6:01:54 PM
Fulton Trailer Coupler E112000340 Review - Video
Today we're going to review part number E112000340, the Fulton Fas-Lok Coupler. This coupler is designed to fit 1-7/8" hitch ball and fit a 2" channel. It is a trigger latch design. It is a bolt-on coupler. It uses a clear zinc finish. We'll do a couple of measurements here. more
Watch Video
Posted: 1/25/2012 6:01:49 PM
Dutton-Lainson Trailer Coupler DL13897 Review - Video
Today we're going to review part number DL13897, the Dutton Lainson Trailer Coupler for a 2" Hitch Ball that will fit on a 3" Channel Tongue. This trailer coupler is a trigger latch hitched design, which will latch on to a 2" hitch ball. It is a bolt-on coupler, designed for a 3" channel tongue. This coupler does have a weight capacity of 5,000 pounds. A few measurements we will do on this coupler. For the channel coupler it would be 3". more
Watch Video
Posted: 1/25/2012 6:01:41 PM
Dutton-Lainson Trailer Coupler DL13847 Review - Video
Today we'll be doing a review on part number DL13847, a Dutton-Lainson Trailer Coupler for a 2" Hitch Ball that will fit on a 2-1/2" Channel Tongue. This is a bolt-on coupler. It uses a Quick-Lock ball clamp assembly with a trigger latch. This coupler has a weight capacity of 3,500 pounds. It has a zinc TUFFPLATE finish, which will offer three times the corrosion resistance, as compared to a regular zinc plate finish. Couple of measurements we will give you on this. more
Watch Video
Posted: 1/25/2012 6:01:35 PM
Dutton-Lainson Trailer Coupler DL13835 Review - Video
Today, we'll be doing a review on part number DL13835, the Dutton- Lainson-Trailer-Coupler for a 2" hitch ball that fits on a 2" channel tongue. This is a bolt on coupler. It does use the quick lock ball clamp assembly with a trigger latch. This coupler has a weight capacity of 3,500 pounds. It does have a zinc TUFFPLATE finish, which has 3x the corrosion resistance of a standard zinc plate finish. Couple measurements we will take on this, On the inside-to-inside, which is 2" for the 2" channel tongue. more
Watch Video
Posted: 1/25/2012 6:01:30 PM
Dutton-Lainson Trailer Coupler DL13728 Review - Video
Today, we're going to review part number DL13728. The Dutton-Lainson-Trailer-Coupler showed a 1-7/8" hitch ball on a 3" channel tongue. This coupler uses a trigger-latch design. It is a bolt on coupler. This has a weight capacity of 2,000 pounds. It does use a zinc TUFFPLATE finish, which has 3x the corrosion resistance of a standard zinc finish. Couple measurements we will do here. more
Watch Video
Posted: 1/25/2012 6:01:22 PM
Master Lock Trailer Coupler 2835AT Review - Video
Today, we're going to review part number 2835AT Master Lock Trailer Coupler for a 2" hitch ball. It will fit a 2-1/2" channel tongue. This coupler is the trigger latch design. It is a bolt-on coupler. It fits a hitch ball size of 2". This is zinc plated. more
Watch Video
Posted: 1/25/2012 6:00:21 PM
Master Lock Trailer Coupler 2833AT Review - Video
Watch Video
Posted: 1/25/2012 6:00:14 PM
Reese Trailer Coupler RP94622 Review - Video
Today we are reviewing the Reese Goose Box, it is a replacement pin box for your 5th wheel trailer that allows you to tow with a Gooseneck in the bed of your truck. It features an air ride air bag, and dual shock absorbers to reduce shocking, jarring, and bounce of the 5th wheel trailer while towing, and has an easy to use coupler latch. This pin box eliminates the need for a Gooseneck adapter to go from the 5th wheel pin to the goose neck ball in the bed of your truck, and is endorsed by Leopard the manufacturer of many pin boxes, will not void the frame or the 5th wheel warranty. This pin box has a 15,000 pound capacity with 3,200 thin weight capacity, and will significantly help improve the ride of your 5th wheel trailer when towing with a Gooseneck hitch in the bed of your truck. more
Watch Video
Posted: 11/29/2011 6:00:17 PM
Replacing A Hydraulic Coupler Demonstration - Video
Today we are going to show you how to replace a hydraulic coupler. In this case this one is damaged and is going to get replaced by a totally different model. First thing we are going to do is actually drain all the fluid from the master cylinder. And what we are actually going to do is open up one of the wheel cylinders and pump our fluid out and into a holding container. All right we will go to the wheel cylinder now and attach a rubber line to the bleeder valve and get our container ready. What we will do is take the cover off our bleeder valve here and we will go ahead and open it up. Okay, here we just take a rubber hose and just slide it on to the bleeder valve itself. All right and then we will just run the other half of the hose into an empty container here and start draining the fluid out of the master cylinder. more
Watch Video
Posted: 8/25/2009 2:00:30 PM
