Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Ford Explorer- Video
Today we have a 2013 Ford Explorer and were going to be test fitting the Thule SUP Taxi Stand Up Paddle Board Carrier part number TH810. Our Explorer is equipped with factory rails and our Thule AeroBlade Roof Rack. To install the Thule SUP Taxi, well take one part of the carrier and set it up on the front load bar. Well feed the speed-link strap around the front load bar and back into the heads. Well use the gray knobs to hand tighten down the straps. Next well take the second half of the carrier and place it on top of the rear load bar.more
Watch Video5/11/2013 11:45:07 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2008 Nissan Sentra- Video
Today on our 2008 Nissan Sentra we're going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number th810. To do this we'll take half of the carrier and set it up on top of the front crossbar. We'll feed the spring link straps around the crossbar and back into the heads. Then we can use the hand notch to tighten down each strap. Next we'll take the second half of the carrier and place it on top of the rear crossbar. We do want to make sure that the rear half lines up nicely with the front half.more
Watch Video4/24/2013 10:09:30 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2014 Jeep Patriot- Video
Today on our 2014 Jeep Patriot, were going to be testing the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH 810. To mount our carrier, well take half of the carrier and set it up on top of the front load bar. We will feed the Speed-Link straps around the load bar and back into the heads. Then, we can use the hand knobs to tighten down the straps. Next, well take the second half of the carrier and place it on top of the rear load bar. We do want to make sure that the second half lines up nicely with the front half so we can carry our paddleboard in a nice straight line.more
Watch Video4/22/2013 9:57:14 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review- Video
Today, we'll be reviewing the Thule SUP Taxi Standup Paddle Board Carrier, part number TH810. This is a single, or a double, standup paddle board carrier system that is designed to attach to most factory roof rack systems as well as Thule roof racks and other aftermarket systems. This paddle board carrier is designed to carry up to two paddle boards no more than 34 inches wide. Before we install it onto our vehicle, we need to make sure that our crossbar spread is at least 24 inches apart. this is the measurement from the center of the front crossbar to the center of the rear crossbar. Next, we'll need to adjust the telescoping saddles to fit our paddle board.more
Watch Video4/19/2013 11:16:08 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Dodge Ram- Video
Today on our 2013 Dodge Ram Pickup, well be test fitting the Thule SUP Taxi Standup Paddle Board Carrier, part number TH810. To mount our carrier, well take the first half and set it up on top of the front load bar. Well feed the speed length straps around the bar and back into the heads and then tighten them down with the grey knobs. Then well take the second half of the carrier and repeat the same procedure at the rear bar. We do want to make sure that, the second half lines up nicely with the front half, so that we can properly carry our paddle board. That is it for our test fit of the Thule SUP Taxi Standup Paddle Board Carrier, part number TH810 on our 2013 Dodge Ram Pickup. .more
Watch Video4/12/2013 12:37:37 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Volkswagen Passat- Video
today on our 2013 Volkswagen Passat, we'll be test fitting the Thule SUP Taxi stand-up paddle board carrier, with a two-board capacity, part number TH810. Now with the roof rack system already installed on our vehicle, we'll begin our test fit by placing the front part of the carrier onto the front cross bar. We'll loosen up the gray knobs to allow the strap to go around the underside of the cross bar, and will then hook it back into the head of the top bracket. We'll then tighten down the gray knob to tighten down the strap to secure the carrier to the cross bar. We will repeat these steps for both brackets on the front part of the carrier. We'll now place the rear part of the carrier onto the vehicle's rear cross bar, and again loosen up the gray knobs to allow us to bring the rubber-coated stainless steel straps around the underside of the cross bar, and will then hook them back into the head of the top bracket.more
Watch Video4/11/2013 11:53:47 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Honda CR-V- Video
Today on our 2013 Honda CR-V, we're going to be test fitting the Thule SUP Stand-Up Paddleboard Taxi, part number TH810. Our CR-V already has a factory roof rack system on it and our SUP Taxi is already preassembled, so we're ready to go ahead and fit it to the vehicle. We'll start with the front carrier. Securing it on the front crossbar, we'll bring the rubber coated straps around underneath the crossbar and reattach them to the carrier where we can tighten down the gray wing nut on either side. We'll then move to the rear crossbar. We do want to make sure that our front and rear carrier line up with each other to make it easier to load our SUP.more
Watch Video4/10/2013 3:03:03 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2011 Chevrolet Equinox- Video
Today on our 2011 Chevrolet Equinox were going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number th810. To mount our carrier on top of our roof rack, well take the first half of the carrier and set it up on top of our front load bar. Well fit the rubber-coated steel SpeedLink straps around our load bar and re-secure them to their heads. We can go ahead and secure them by tightening them down with the gray hand knobs. With the front half of our carrier secured, well take the second half of the carrier and set it up on top of the rear load bar. We do want to make sure that it lines up properly with the carrier in front.more
Watch Video4/10/2013 3:02:59 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Toyota Corolla- Video
Today on our 2013 Toyota Corolla well be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier with a two board capacity, part number th810. To begin our test fit, well place the front part of the carrier onto the front crossbar. Well bring the rubber-coated steel straps around the underside of the crossbar and hook them into position. Note, that you may need to loosen up the steel straps in order to be able to bring the straps around the crossbar. After the straps are in position, we can then turn the gray knob to tighten down the straps and secure the carrier to the vehicles front crossbar. Well now set the rear part of the carrier onto the rear crossbar, bring the rubber-coated steel straps around the underside of the crossbar and hook them into position.more
Watch Video3/22/2013 9:01:45 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Jeep Grand Cherokee- Video
Today on our 2012 Jeep Grand Cherokee, well be test fitting the Thule SUP Taxi Standup Paddle Board Carrier, part number TH810. Now this carrier gives you the ability to carrier up to 2 boards. With our vehicle already equipped with the Thule AeroBlade, were ready to fit it to the vehicle. Well take the front carrier, place it over the front crossbar, and make sure that the rubber-coated steel straps go underneath the crossbar where well reattach them to the foot itself. We can then turn the gray knob, winding the rubber-coated steel strap up, and securing the carrier to our crossbar. Well do this on both sides of our carrier and secure the front carrier to the front crossbar.more
Watch Video3/12/2013 9:19:19 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Dodge Durango- Video
Today on our 2012 Dodge Durango, we'll be test fitting the Thule SUP Taxi stand up paddle board carrier with a 2 door capacity, part number TH810. Now this vehicle is equipped with factory installed cross bars, so to begin our test fit, we'll set the first part of the carrier onto the front crossbar. We'll bring the rubber coated steel straps on the underside of the crossbar and turn the gray knob to tighten it down to secure the carrier to the vehicle. We will repeat this process for the other side with the strap. We will then move to the rear of the vehicle. We will then set the second part of the carrier onto the rear crossbar.more
Watch Video2/1/2013 11:55:42 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Ford Escape- Video
Today on our 2013 Ford Escape, well be test fitting the Thule SUP Taxi Stand-Up Paddle Board Carrier, part number TH810. Now with our roof rack system already assembled to the vehicle, well go ahead and set the carrier onto the front crossbar, swing the rubber coated steel straps on the underside of the crossbar, bring them up, snap them into position and turn the grey knobs to tighten them down and secure the carrier to the crossbar. We can then repeat this process for the rear crossbar. It is important to get the paddle board carriers perpendicular to each other to ensure that your paddle boards are secured down correctly. To load our cargo, well undo the grey plate at the face of the carrier; this will allow us to bring out the slack of the rope. That completes todays test fit for the Thule SUP Taxi Stand-Up Paddle Board Carrier with a two board capacity, part number TH810 on our 2013 Ford Escape.more
Watch Video1/22/2013 9:22:39 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Volkswagen Passat- Video
Today on our 2012 Volkswagen Passat, well be test fitting the Thule Taxi Stand-Up Paddleboard Carrier, part number TH810. To begin our test fit, well set the carrier on top of the crossbar and bring the rubber coated steel strap around the underside of the bar and tighten it down with the grey knob. Well then repeat these steps for the rear crossbar. Once you get the carriers tightened down, were ready to load our cargo. Well undo the silver latch located at the front face of the carrier to allow us to bring the black rope out. You will then be able to put your cargo onto the carrier and then tighten it down and secure it with the grey latch again.more
Watch Video1/14/2013 10:32:20 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Kia Soul- Video
Today on our 2012 Kia Soul well be test fitting the Thule SUP Taxi standup paddleboard carrier, part number TH810. To begin our test fit well take the paddleboard carrier, set it on the front load bar, wrap the strap around the load bar and tighten with the grey knob. Well then set the paddle carrier onto the back load bar, wrap the strap around the load bar and secure it with the grey knob. That concludes todays test fit for the Thule SUP Taxi standup paddleboard carrier, part number TH810 on our 2012 Kia Soul.more
Watch Video1/9/2013 2:54:51 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Kia Sorento- Video
Today on our 2013 Kia Sorento, we'll be testing fitting Part Number TH810. The Thule SUP Taxi Stand Up Paddleboard Carrier. Now to begin, we'll simply take our front carrier, place it on top of our front crossbar, bring the rubber coated steel straps underneath the crossbar and secure them back to the foot of the carrier. We can then turn the grey knob, securing the front carrier to the front crossbar. With that done, we'll now move on to our rear carrier. We'll now place it on top of the rear crossbar and make sure that it's in line with our front carrier.more
Watch Video12/26/2012 3:12:46 PM
Darby Extend-A-Truck Kayak Carrier Review- Video
Watch Video12/26/2012 1:59:24 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Honda Ridgeline- Video
Today on this 2013 Honda Ridgeline well be test fitting the Thule Standup paddle board carrier, part number TH810. To begin our test fit sit the carrier on top of the crossbars, wrap the black straps around the crossbars and turn the gray knobs to tighten. You want to make sure that your carriers are parallel to each other and that they are position symmetrically to the crossbars so that your cargo can be secured correctly. That concludes todays test fit for the Thule Standup paddle board carrier, part number TH810, on this 2013 Honda Ridgeline.more
Watch Video11/15/2012 3:38:29 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2011 Chevrolet Malibu- Video
Today on our 2011 Chevrolet Malibu, we'll be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH810. To mount our carrier to the vehicle, we'll take the first half and set it up on top of our front load bar. We'll feed the speed link straps around our load bar and fit them back into the heads. We'll then use the gray hand knobs to tighten down the straps. We'll take our second half of the carrier and place it up on top of our rear bar. We do want to make sure that it lines up nicely with the front half so we can properly carry the paddleboard.more
Watch Video10/19/2012 1:43:06 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Dodge Journey- Video
Today on our 2013 Dodge Journey well be test fitting the Thule SUP Taxi Standup Paddle Board Carrier, part number TH810. To mount our carrier well take the first half and set it up on top of the front load bar. Well feed the speed link straps around the bar and back into heads then tighten them down with the gray knobs. Then well take the second half of the carrier, and repeat the same procedure at the rear bar. We do want to make sure that the second half lines up nicely with the front half so that we can properly carry our paddle board. Thats it for our test fit of the Thule SUP Taxi Standup Paddle Board Carrier, part number TH810 on our 2013 Dodge Journey..more
Watch Video9/28/2012 2:14:44 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Dodge Grand Caravan- Video
Today on our 2013 Dodge Grand Caravan, we'll be test fitting the Thule SUP Taxi Stand-UP Paddleboard Carrier, part number TH810. Now to begin our test fit, we'll place the front carrier on top of our front crossbar. We'll make sure the rubber coated steel straps go underneath the crossbar where we can then hook them back to the foot of the SUP taxi. We'll then turn the gray knob here, tightening the strap, securing our carrier to the crossbar. We'll do this on both sides. With our front carrier in place, we're now ready to load the rear carrier.more
Watch Video9/27/2012 1:44:02 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2009 Dodge Journey- Video
Watch Video9/13/2012 11:35:54 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2007 Kia Sportage- Video
Today on our 2007 Kia Sportage, well be test-fitting part number TH810. This is the Thule SUP Taxi Stand-Up Paddleboard Carrier. Now, to begin our test fit, well simply place the front carrier over the top of the front crossbar. After determining a suitable location on the crossbar, well use the rubber coated steel strap to go underneath the crossbar and secure it back to the foot of the SUP carrier. Well then use the gray knob on the foot to tying down the carrier strap and secure it to the front crossbar. Well do these on both feet of the front carrier.more
Watch Video9/11/2012 9:06:22 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Honda Civic- Video
Today on our 2012 Honda Civic, were going to be test fitting the Thule SUP Taxi Stand -Up Paddleboard Carrier, part number TH810. To mount our carrier to our roof rack, well take the first half of the carrier and set it up on top of our front load bar. Well feed the speed link straps around the load bar and fit them back into the head, and then well tighten them down with the gray hand knobs. Then we will take the second half of our carrier and place it up on top of the rear load bar. We do want to make sure that the second half lines up nicely with the front half. Well fit our speed link straps around the bar, again re-securing them to the head and tighten them down with the gray hand knobs and with that our paddleboard carrier is mounted to our roof rack and were ready to start loading up.more
Watch Video9/7/2012 2:54:16 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Toyota Corolla- Video
Today were working with a 2012 Toyota Corolla and were going to be test fitting the Thule SUP Taxi Standup Paddleboard Carrier. To mount the carrier to our vehicle well take the first half of the carrier and place it up on top of our front load bar. Well feed the speed link straps around, well resecure them to the heads and tighten them down using the gray hand knobs. Next well take the second half of the carrier and place it up on top of our rear bar. We do want to make sure that the rear half lines up nicely with the front half. Again, well feed the straps around, secure them to the head and tighten them down with the knobs.more
Watch Video8/31/2012 1:39:33 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Honda Accord- Video
Today on our 2012 Honda Accord, well be test fitting part #TH810. This is the Thule SUP Taxi Standup Paddleboard Carrier. Now, to begin our test fit, well place our front carrier on top of a front crossbar. Well then take the rubber-coated steel straps, wrap them underneath the crossbar, and bring them back up, securing them back to the foot of the carrier. We can then turn the gray knob, tightening down the strap, securing our carrier to the front crossbar. Well now place the rear carrier on top of the rear crossbar, again making sure that the rubber-coated steel straps run underneath the crossbar, where well reattach them on the other side.more
Watch Video8/30/2012 11:14:14 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2008 Subaru Legacy- Video
Today on our 2008 Subaru Legacy GT, well be test fitting the Thule SUP Taxi Stand-Up Paddle Board Carrier, part number TH810. To mount our carrier to the vehicle, well take the first half of the carrier and set it up on top of the front load bar. Well run the speed link straps around the load bar, fit them back into the head, and tighten them down using the gray hand knob. Once weve done that, we can move back to the second half of the carrier. We do want to make sure that the second half lines up nicely with the front half. Again, well fit the speed link straps around our load bar and back into the head, tightening them down the same way we did the first.more
Watch Video8/28/2012 10:47:44 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2011 Ford Flex- Video
Today we're working with a 2011 Ford Flex and we're going to be test fitting a Thule SUP Taxi Stand-Up Paddleboard Carrier part number TH810. To mount our carrier to our roof rack we'll take half of the carrier and set it up on top of the front load bar. We'll position it where we want it and feed the spindling straps around the load bar and secure them back to the head. We'll then use the hand knobs to tighten down the straps on both sides of the vehicle. Then we'll take the second half of the carrier and place it on the rear bar. We do want to make sure that it lines up nicely with the front so that we can carry our paddleboard.more
Watch Video8/14/2012 3:08:23 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Toyota Highlander- Video
Today, we've got a 2012 Toyota Highlander and we're going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH810. To mount our carrier up on top of our roof rack, we'll take the first half of the carrier and set it up on top of our load bar. We'll fit the rubber coated steel speed link straps around our load bar and re-secure them to their heads, tightening them down with the gray hand knobs. With the front half of our carrier secured, we'll take the second half of the carrier and set it up on top of the rear load bar. We do want to make sure that it lines up properly with the carrier in front. Again, we'll feed the speed link straps around the bar and tighten them down with the hand knobs.more
Watch Video8/10/2012 12:35:25 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2008 Mercury Mariner- Video
Today we have a 2008 Mercury Mariner and were going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier part number TH810. Our mariner is equipped with a full factory roof rack so were going to mount the Thule SUP Taxi directly to the factory crossbars. To do this well take half of the carrier and set it up on top of the front crossbar. Well feed the speed link straps around the crossbar and back into the heads. Then we use the hand knobs to tighten down the straps. Next well take the second half of the carrier and place it on top of the rear crossbar.more
Watch Video8/8/2012 11:25:44 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Honda Fit- Video
Today on our 2012 Honda Fit were going to be test fitting the Thule SUP Taxi Standup Paddleboard Carrier part number TH810. To mount the carrier up to our roof rack were going to take half of the carrier and set it on top of our front load bar. Well feed the straps around the load bar, fit them back into the speed link head and use the hand knobs to tighten them down. With the front half tightened down well move back to the rear crossbar. Well take the second half of the carrier and set it up on the rear bar. Well repeat the same tightening procedure that we used up front.more
Watch Video8/7/2012 9:19:26 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2007 Honda Civic- Video
Today, we have a 2007 Honda Civic Sedan and we're going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH810. To fit the paddleboard carrier to our roof rack, we'll take the first half and set it up on top of our load bar. We'll fit the speed link straps around our bar and back to the heads and tighten them down with the hand knobs. Once we have the front half secure, we'll put our second half up on top of our rear bar, make sure its lined up with the first and repeat the same tightening procedure. With both halves tightened to our load bars, we're ready to load up and hit the road. That's it for our test fit of the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH810 on our 2007 Honda Civic Sedan..more
Watch Video7/26/2012 11:54:17 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2007 Hyundai Santa Fe- Video
Today we have with us the 2007 Hyundai Santa Fe and were going to be test fitting the Thule Standup Paddleboard Taxi part number TH810. Our Santa Fe already has a full factory roof rack so well just mount the SUP Taxi directly to our factory crossbars. Well take the first half of our carrier and place it up on top of our crossbars. Well feed the Speed Link straps around our crossbar and use the hand knobs to tighten them down. Once we got the first half tightened down, well take the second half and put it over our rear bar. We just want to make sure that it lines up with the front half and again tighten down the Speed Link straps.more
Watch Video7/25/2012 1:06:26 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2007 Volvo XC90- Video
Today, we have with us a 2007 Volvo XC90, and were going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH810. To fit our carrier up on top of our roof rack, well simply take the first half of the carrier and lay it on top of our front load bar. Well feed the speed link straps around the load bar, secure it back to itself and tighten it down using the gray hand knob. We want to make that we tighten both the passenger and drivers side straps down evenly. With the front carrier installed, well move to the back half of the carrier. We want to make sure that its lined up evenly with the front carrier, feed the straps around again and tighten it down the same way.more
Watch Video7/13/2012 9:27:44 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2003 Toyota RAV4- Video
Today on our 2003 Toyota RAV4, were going to be test fitting the Thule SUP Taxi Standup Paddleboard carrier, part number TH810. Our RAV4 is equipped with a factory roof rack, so all we need to do is mount our SUP Taxi up on the factory crossbars. Well take the first half of our carrier and set it up on top of our front crossbar. Well wrap the speed link straps around the crossbar, secure them back to the head of the clamp, and use the wing knobs to tighten it down. Well just take the second half of the carrier, make sure that its lined up with the first and repeat the same tightening procedure. With that, our paddleboard carrier is installed on the roof rack and were ready to load up.more
Watch Video7/2/2012 9:44:45 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2008 Toyota RAV4- Video
Today on our 2008 Toyota RAV4, were going to be test fitting the Thule SUP Taxi Standup Paddleboard carrier, part number TH810. To mount the carrier to our vehicle, well take the first half and set it on top of our front crossbar. Well fit the straps around the bar, re-secure them to the head and use the hand knobs to tighten them down. With the front half secure, we can move on to the rear. Well take the second half of the carrier and place it on top of the rear bar. We want to make sure that the second half of the carrier lines up nicely with the first.more
Watch Video6/29/2012 1:35:44 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2010 Infiniti FX35- Video
Today, on our 2010 Infiniti FX35, we are going to be test fitting the Thule SUP Taxi stand-up paddleboard carrier, part number TH810. Our FX35 is already equipped with a full factory roof rack, so we are going to mount our SUP taxi directly to the factory crossbars. To do this, we will take the first half of the carrier and set it up on top of our front crossbar. We will position it where we want it, feed the speed link straps around the cross bar, secure them back to the speed link head, and use the hand knobs to tighten it down. Once we have both sides tightened down, we will grab the second half of our carrier and put it up on top of the rear crossbar. We will repeat the same tightening procedure, but we just want to make sure that the second half lines up nicely with the first half.more
Watch Video6/29/2012 7:57:28 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Nissan Versa- Video
Today we have with us a 2012 Nissan Versa and we're going to be test fitting the Thule SUP Taxi Stand-Up Paddle Board Carrier, part number TH810. To mount the SUP Taxi to our roof rack we'll take the first half of the carrier and set it up on top of our front load bar. We'll feed the straps around the load bar and back to the speed link head and tighten it down with the hand knob. Next we'll take the second half of the carrier and set it up on a reel load bar making sure that we line it up even with the front half. Once we've done that we'll repeat the same procedure as the front for tightening the straps around the load bar. And with that our SUP Taxi is mounted to our roof rack and we're ready to load up and hit the road.more
Watch Video6/21/2012 12:05:27 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Toyota Sequoia- Video
Today on our 2012 Toyota Sequoia we are going to test fit the Thule SUP, taxi, part number TH810. With the vehicle equipped with the manufacturer's roof rack system and our carrier already pre-assembled we can go ahead and put it directly on the load bars of our roof rack system. For today's application we are going to go ahead and mount it in the center of the vehicle. Using the speed link universal mounting system, we can quickly and easily secure our carrier to the load bars. And there you have it, in just a few simple steps we've gone ahead and secured our carrier to the roof rack system. Now we are ready to hit the road and that does it for our test fit of the Thule Taxi Stand-Up Paddleboard Carrier, part number TH810 on our 2012 Toyota Sequoia..more
Watch Video6/13/2012 10:37:24 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Dodge Charger- Video
Today on this 2012 Dodge Charger, we're going to do a test fit of party number TH810; the Thule SUP Taxi. Now our charger has already been equipped with a roof rack system using a Thule AeroBlade Crossbars. We'll start off our carrier already assembled according to the instructions, so all we have to do is put it on the roof rack. We'll take our first carrier, place it up on the roof rack and then wrap the straps underneath the AreoBlade bar and then the clips on the other side. Once we have it loosely attached, we'll go ahead and move it into its final position and tighten it down for good. Okay, we got the first half in placed and we'll go ahead and move on to the second half, we will repeat the same steps that we used to install the first half of the carrier.more
Watch Video6/6/2012 1:10:01 PM
Rhino Rack Watersport Carriers S511 Review- Video
Today we are going to review part number S511. These are the Rhino rack J Style kayak carriers. They are folding carriers and they are universal mount. This carrier is shown in the J position. Your kayak would be lying right on here on its side. This does attach with the brackets on the bottom to round crossbars, arrow and elliptical crossbars and most factory crossbars.more
Watch Video5/16/2012 12:17:49 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2010 Jeep Compass- Video
Today on our 2010 Jeep Compass, well be test fitting part number TH810, the Thule SUP Taxi, Stand Up Paddle board carrier. Thatll begin our test fit. Well place the front carrier over the top load bar, well bring the rubber coated steel strap underneath the load bar and re-secure it to the foot of the front carrier. We can then tighten it down using the gray knob here on the side of the carrier. With the front carrier secured to the vehicle, well go ahead and move to the rear carrier. Again, well place the rear carrier on top of the rear load bar; well bring the rubber coated steel straps underneath the load bar and secure them to the carrier.more
Watch Video4/26/2012 4:06:22 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Ford Fusion- Video
Today we have a 2012 Ford Fusion and we'll be test fitting the Thule SUP taxi stand up paddle board carrier, part number TH810. To mount the carrier up on top of our roof rack, we'll take the first half, set it on top of the load bar and feed speed link strap around. And we'll use the gray hand knob to tighten it down. We'll back and forth from driver side to passenger side to make sure we tighten down the system evenly. Once we have the first half attached, we can move on to the rear half and secure it on our rear load bar. With that the SUP is mounted and we're ready to load up and hit the road.more
Watch Video4/23/2012 8:34:52 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Jeep Compass- Video
Today on this 2012 Jeep Compass were gonna be test fitting the Thule SUP Taxi Stand-Up Paddle Board Carrier part number TH810. To mount the SUP Taxi up on our roof rack, were gonna take half of the carrier and set it up on top of our front load bar. Well take the rubber coated steel strap and fit it around and back into the speed link head. Well use the gray hand knob to tighten it down. Then well then move to the driver side and tighten the strap over there. Well take the second half of the carrier, take it to the rear load bar and repeat the same procedure.more
Watch Video4/10/2012 2:09:06 PM
Yakima LandShark Saddles for Roof Rack Crossbars Review- Video
Today were going to review part number Y04030 Yakima. This is a LandShark Kayak Carrier. Were gonna do a review on a 2012 Toyota Forerunner. One thing with this vehicle is that its already been equipped with a Yakima Roof Rack system using the round bars. Well go ahead and start off with our review. Well go ahead and take the Mighty Mounts and attach them to the crossbars.more
Watch Video4/9/2012 2:12:09 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Toyota Camry- Video
Today we have a 2012 Toyota Camry and well be test fitting the Thule SUP Taxi Stand-Up Paddle Board Carrier part number TH810. To fit the carrier on our roof rack, well take the first half, set it on top of our front load bar and well wrap the speed link strap straps around the bar and seat them back in the head. Well then use the hand knobs to tighten it down. Well then move to the rear bar and repeat the same position with the other half of our carrier. Once weve done that, our bike carriers mount into our roof rack and were ready to load it up and hit the road. That does it for out test fit of the Thule SUP Taxi Stand-Up Paddle Board Carrier part number TH810 on our 2012 Toyota Camry..more
Watch Video4/5/2012 2:05:19 PM
Rhino-Rack S400 Series Saddle-Style Kayak Carrier Review- Video
Were going to do a demo of the Rhino Kayak Carrier, part number S400. This will be in conjunction with the Rhino Rack Roof System Kit, part number S400-FK1. When purchasing this kit together, part number will be S400-1. With our load bars already set up on the vehicle, well need to remove the center rubber stripping in the center of our load bar. Alright, to remove the rubber, well go ahead and unlock the endcap and remove it first, then we can simply peel it out of the T bolt. Well go ahead and do this for both the front and rear load bar setup.more
Watch Video4/5/2012 1:10:26 PM
Thule Hullavator Kayak Carrier System Review- Video
Today well be reviewing part number TH897XT, the Thule Hullavator Lift-Assist Kayak Carrier. This carrier will carry one kayak up to 36 inches wide and 75 lbs. When first receiving your Hullavator, there is some assembly required. This kayak carrier will work on Thule Square Bars as well as Yakima Round Bars, will also work on Thule Rapid Aero and Xsporter Load Bars. Once weve checked our packaging to make sure everythings here, well go ahead and begin assembling. You need to make sure that your crossbars have a minimum of 4 inches extending from the foot.more
Watch Video4/3/2012 2:18:05 PM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Volkswagen Jetta- Video
Today on this 2012 Volkswagen Jetta we're going to be test fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, part number TH810. We'll take the first half of our Stand-Up Paddleboard Carrier and place it over the front load bar. We'll wrap the rubber coated steel straps around our load bar, secure the back to the tightening clamp, and then use the gray knob to tighten it down. We'll move back and forth from driver's side to passenger's side to make sure we tighten down the carrier evenly. Once we've tightened down the front piece, we can move on and tighten down the rear half. With both halves tightened down, our carrier is installed and ready to use.more
Watch Video3/29/2012 10:37:46 AM
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2011 Ford Fiesta- Video
Today we have a 2011 Ford Fiesta Five-Door Hatch. Well be test fitting the Thule SUP Taxi Stand-up Paddleboard Carrier, part number TH810. To secure the carrier, well take the speed link straps and wrap them around our load bar. Well hook them back into the base and begin tightening the grey knob. Once weve done that for the first half of the carrier on the front bar, we can move to the rear bar and repeat the same. With that, our stand-up paddleboard carrier is installed.more
Watch Video3/26/2012 2:06:53 PM
