Buffalo Tools Truck Bed Accessories BTBB07582 Review- Video
Today were going to review part number BTBB07582. This is the Buffalo Tools Black Bull pickup truck crane with a hand winch. This heavy-duty crane will mount into your truck bed and let you safely and easily lift cargo and equipment into and out of your pickup. It has the four boom positions; one, two, three, four, and each one as you move that boom out it will reduce the weight capacity. Right now we have it in max which is 1,000 pounds so the closer this boom is to the base would be more weight capacity. The furthest out position with it extended fully out would be 500 pounds.more
Watch Video4/12/2013 9:16:23 AM
Buffalo Tools Truck Bed Accessories BTBB07583 Review- Video
Today we're going to take a look at the Buffalo Tools Black Bull pickup truck crane, number BTBB07583. This is a truck-bed-mounted crane that lets you safely and easily lift cargo and equipment into and out of your pickup. It features two boom positions. Right now it's in the closest position. That allows you to support heavier loads. You would move this bolt here, pull it out, extend this out and then replace the bolt right here, and that would provide a longer range to lift more out of the way cargo.more
Watch Video4/11/2013 2:15:54 PM
Stromberg Carlson Tailgate Installation - 2006 Ford F-150- Video
Today on our 2006 Ford F150, well be test fitting the Stromberg Carlson 100 series fifth wheel tailgate with open design, part number VG-04-100.Now to begin our test fit, we will first start off by removing our manufacturers tailgate. Well open up the tailgate and lay it down flat. Well then move to the support straps attached to the truck bed, lift up the silver plate to allow us to bring the strap up off of the hook. We will then repeat these steps for the other side. Note that you do need to keep a hold on the tailgate as once both straps have been removed, the tailgate will not have any support.Well then put the tailgate in a 45 degree angle and lift up on the passenger side of the tailgate. Once the passenger side is free, we can then slide the tailgate to the right and allow the drivers side of the tailgate to pop out.Now with the new hardware installed on the fifth wheel tailgate, well start off by inserting the rubber bushing on the drivers side of the truck bed.more
Watch Video3/15/2013 1:04:22 PM
DeeZee Tailgate Assist Installation - 2003 Ford F-250- Video
Today on our 2003 Ford F250 Super Duty we'll be installing the DeeZee Tail Gate Assist, part number DZ43203. Our first step will be opening the tail gate. Next we'll go ahead and prepare and install the nutsert. Using the nutsert and nutsert tool we'll need to set the depth. There'll be 3/4 of an inch from the face of the washer at the end of the nutsert tool. Now we've got our depth set we'll go ahead and install it into the pre-drilled hole in the tail gate near the hinge.more
Watch Video3/1/2013 4:13:23 PM
Stromberg Carlson Tailgate Installation - 2007 Chevrolet Silverado- Video
Today on this 2007 Chevrolet Silverado 2500 Series new body style; were going to do a test fit for part number, VGM-07-100. Were going to start off with our tailgate already removed and well go ahead and take the new tailgate and put it into place. First off, we are going to take the bushing that comings with the tailgate, install it on the pin on the driver side. Then well take the tailgate and slide it over that bushing and then we can go ahead and install the tailgate just like any other tailgate. Well go ahead and take the latch and well pull it in a little bit on each side and then push the tailgate into place until it snaps in. Inaudible 00:00:40 like your tailgate matches the contour of the bed by the taillight.more
Watch Video2/1/2013 1:28:29 PM
Stromberg Carlson Tailgate Installation - 2008 Ford F-350- Video
Today on this 2008 Ford F350 were going to do a test fit of part number VG-97-4000. This is Strongberg Carlson 4000 Series fifth wheel louvered tailgate. This tailgate has a cut out for towing a fifth wheel or gooseneck trailer. It also constructed from a glass filled, black composite plastic frame and louvers. It also has a louver design that helps reduce drag. The tailgate is lockable.more
Watch Video12/26/2012 10:02:25 AM
Stromberg Carlson Tailgate Installation - 2002 Ford F-150- Video
Today on this 2002 Ford F150 were going to do a test fit of part number VG-97-4000. This is Stromberg Carlson 4000 Series fifth wheel tailgate. Few things to know this tailgate has a cut out for a fifth wheel or a gooseneck trailer. Its constructed from a black composite plastic frame with built in louvers which allows for less drag and improves visibility. It also has a key center release mechanism that works with the latches. This will allow you to lock the tailgate on the truck.more
Watch Video12/20/2012 1:14:52 PM
Stromberg Carlson Tailgate Installation - 2012 Chevrolet Silverado- Video
Today on this 2012 Chevrolet Silverado were going to do a test fit of part number VGM-07-4000. This is the Stromberg Carlson 4000 series fifth wheel levered tailgate. Well start off our test fit by removing the original tailgate and then well go ahead and install our new tailgate in the same fashion as the original one went in. Well start off on the drivers side. Well put it on the hinge, and then well go over to the passengers side and hold the tailgate at about a 45 degree angle and slide it on to the pin there. Next well go ahead and install the cables onto the original factory mounts.more
Watch Video12/19/2012 12:50:10 PM
Stromberg Carlson Tailgate Installation - 2012 Chevrolet Silverado- Video
Today on this 2012 Chevrolet Silverado, were going to do a test fit of part number VGM-07-100 from Stromberg Carlson. This is our 100 series fifth wheel tailgate, and has a convenient cutout for towing a fifth wheel or gooseneck hitch when youre hitching up. Well start off our test fit with the tailgate already removed from our truck, so lets go ahead and install our new tailgate in the same fashion the original tailgate would. Well start off by sliding the tailgate into the hinge onto the drives side, then well go over to the passengers side, line up the hinge, put the tailgate at about a 45 degree angle and slide it into place. Well go ahead and push it up until our latches meet the pins on the bed. Now well do one pin at a time.more
Watch Video12/19/2012 12:50:07 PM
UWS Truck Bed Accessories UWS020114 Review- Video
Today were going to review part number UWS020114. This is the UWS northern insulated truck bed dog box. This is a crossover style. This tall insulated crossover style dog box is made of lightweight rust proof aluminum. It offers 14 cubic feet of interior space for your favorite hunting dogs. It does have an insulated lid on top which will help retain heat within the box to keep your dogs warm and it makes the top more rigid for additional strength and security.more
Watch Video11/30/2012 12:19:21 PM
UWS Truck Bed Accessories UWS020022 Review- Video
Today were going to review part number UWS020022. This is the UWS southern truck bed dog box. This is the standard chest design with one front door. This tall vented dog box is made of lightweight rust proof aluminum and offers 18 cubic feet of interior space for your favorite hunting dog. It is a vented design which allows excellent airflow to keep your dog comfortable. It is made of an aluminum construction which is durable and rust proof.more
Watch Video11/30/2012 12:18:36 PM
Husky Liners Tailgate Installation - 2003 Ford F-250- Video
Today on our 2003 Ford F250 were going to install the Husky Truck Bed Accessory Tailgate part number HL15130. First, well need to go ahead and remove the manufacturers tailgate cables. To do this well remove the torque headed bolt and set the cables and hardware aside. Then we can go ahead and remove the tailgate by hinging the tailgate to a 45 degree angle and pulling up on the passengers side and sliding the drivers side toward the passengers side to remove the tailgate completely. Before we can install the cable onto the new tailgate well first need to remove the old hardware. To do this, well need to remove the hold down washer and spacer.more
Watch Video11/19/2012 1:39:04 PM
Stromberg Carlson Tailgate Installation - 2012 GMC Sierra- Video
Today on our 2012 GMC Sierra, we'll be test fitting the Stromberg Carlson 100 Series 5th-Wheel Tailgate with open design part #VGM-07-100. This tailgate features an open design that improves your field of vision while driving and is custom fit to your vehicle. The cutout allows for easy towing of 5th-wheel and gooseneck trailers, and its aerodynamic design reduces drag. To begin our installation, we'll need to remove the factory tailgate. This truck is equipped with a backup camera. After the installation of the Stromberg Carlson tailgate, the factory backup camera will no longer be operational.more
Watch Video11/19/2012 10:44:22 AM
Husky Liners Tailgate Installation - 2012 GMC Sierra- Video
Today, on our 2012 GMC Sierra, well be test-fitting the Husky Liners Premium 5th Wheel Louvered Tailgate with Locking Handle, part #HL15240. This custom-fit tailgate features a convenient cutout for towing your fifth-wheel or gooseneck trailer. Its lightweight construction and louvered design help boost your vehicles gas mileage. The factory hinge and latch points make it easier to install. To begin, well need to remove our factory tailgate. Underneath the truck here, right behind the rear license plate is the plug in for the rear backup camera.more
Watch Video11/19/2012 10:44:13 AM
Maxx Tow Hitch Crane Review- Video
Today were going to review the Maxx Tow hitch mounted crane, part number MT07328. Now in this video were actually going to walk through the assembly process as well as how to use it since youll have to assemble it on the vehicle and disassemble it each time you dont need to use it. Well start with the T-connector that well insert into the receiver hitch on our truck and secure it with a pin and clip. Next well assemble the legs onto the base of the crane system. Well use the pins and clips to secure the legs into the welding on tabs on the sides of the base. As you assemble the legs you want to make sure that they are going to sit at the base and at the same height as the receiver tube of the hitch.more
Watch Video11/6/2012 3:35:22 PM
UWS Truck Bed Accessories UWS062107 Review- Video
Today were going to review part number UWS062107. This is the UWS aluminum tracking collar box, black in color. This is a locking, rust proof aluminum box which will help keep your dogs tracking collar safe. It is built of an aluminum construction with fully welded seams, which will guarantee it not to rust. It does have a stainless steel paddle latch that you can use here to open the lid like that, you just push up, pull up on it and itll open the lid. It also has a stainless steel lock with two keys.more
Watch Video10/26/2012 10:20:20 AM
Husky Liners Tailgate Installation - 2013 Chevrolet Silverado- Video
Today on this 2013 Chevrolet Silverado, we're going to do a test fit of part number HL15240. This is the Fifth Wheel Tailgate from Husky Liner. To start off the test fit, we already went ahead and removed the factory tailgate. Now, we'll go ahead and install the new Fifth Wheel Tailgate. Basically, it installs as the same way as the original tailgate. We'll start by installing the pin on the driver's side into the tailgate and we'll go to the passenger's side and we'll line up the slot and put it into place.more
Watch Video10/19/2012 1:35:34 PM
UWS Truck Bed Accessories UWS010504 Review- Video
Today, we're going to review part number UWS010504. This is the UWS Aluminum Tracking Collar Box. This is a locking rust proof aluminum box which will help keep your dogs tracking collar safe. It is built of an aluminum construction with fully welded seams which will guarantee not to rust. It does have a stainless steel paddle latch that you use here to open the lid and it also has a stainless steel lock with two keys. The lid has a beveled edge to it, and just to pull up on it, it will open up the lid.more
Watch Video9/27/2012 12:26:39 PM
Stromberg Carlson Tailgate Installation - 2007 Dodge Ram- Video
Today on our 2007 Dodge Ram 2500, were going to be test fitting the Stromberg Carlson Fifth Wheel Tailgate, part #VGD-02-100. First, well need to remove the OEN tailgate. Well undo the cables. At their securing posts, lower the tailgate to about a 45 degree angle, pull it off the passengers side hinge, and then slide it off the drivers side hinge. Once weve done that, were ready to fit on our Stromberg Carlson gate. Well just reverse the procedure.more
Watch Video8/30/2012 11:11:50 AM
Husky Tailgate Installation - 2010 GMC Sierra- Video
Today, on this 2010 GMC Sierra, were going to do a test fit of part number HL15240 from Husky Liners. This is their Fifth Wheel tailgate. Now, well start off our test fit with our tailgate already removed and our cables transferred from the tailgate to our new Husky Liner tailgate. Now, there are a couple of bushings you have to test fit on the Husky Liner to make sure it works with your truck. When the right bushings are selected, we can go ahead and install the tailgate. We will just install it the same way as original tailgate did.more
Watch Video8/28/2012 10:14:29 AM
Stromberg Carlson Tailgate Installation - 2003 Dodge Ram- Video
Today in this 2003 Dodge Ram Pickup, were going to do a test fit of part number VGD-02-100. This is from Stromberg Carlson. Now, were going to start off our test of it with our tailgate already assembled according to instructions, so all Ill got to do is remove the original tailgate then install the new one. The new tailgate installs just like the original. Well slide it over the pin and keep it tilted back, so we can slide on the other pin on the passenger side then well go ahead and push it up. Well pull the latches out just a little bit, then well go ahead and push the tailgate firmly into place.more
Watch Video8/21/2012 4:11:26 PM
Stromberg Carlson Tailgate Installation - 2006 Ford F-250- Video
Today on our 2006 Ford F250 were going to be test fitting the Stromberg Carlson fifth wheel tailgate, part number VG-97-4000. First, well remove our factory tailgate. Once weve done that were ready to fit on our Stromberg Carlson gate. Well fit our tailgate over the drivers side hinge then over the passengers side hinge. Next, well fit the vinyl ends of our new cables over the attachment points for the old. And with that our tailgates installed.more
Watch Video8/15/2012 12:37:09 PM
Stromberg Carlson Tailgate Installation - 2011 Dodge Ram- Video
Today, on our 2011 Dodge Ram 1500, we are going to install part number VG-10-100. This is a Stromberg-Carlson fifth wheel tailgate. To start of our install, we need to go ahead and remove the existing tailgate. The tailgate comes with bushings we will install on the tailgate on the driver side on that pin and then on the passenger side, the bushing will install over here. We will go ahead and start installing our tailgate, we will slide it onto the bushing on the driver side. Keeping the tailgate tilted, we will go ahead and install it on the passenger side.more
Watch Video6/29/2012 12:34:41 PM
Stromberg Carlson Tailgate Installation - 2006 Ford F-250- Video
Today, on our 2006 Ford F-250, we are going to be test fitting the Stromberg-Carlson open fifth wheel tailgate, part number VG-97-100.All right, we have already got our tailgate assembled so now we are ready to mount it up on our truck. First we need to remove the factory tailgate. We will lower the tailgate and we will undo the support cables on either side of the tailgate. We will turn the tailgate to about a 45 degree angle so that we can slide the hinge on the passenger side off. To fit up our Stromberg tailgate, again we will hold it at about a 45 degree angle and we will slip the driver side over the hinge post first. As we close the tailgate, we want to pull open the latches, push the tailgate into position and release the latches so they will hold the tailgate in place.more
Watch Video6/29/2012 12:34:22 PM
Putco Push-Up Tie-Downs Installation - 2012 Ford F-150- Video
Today, on our 2012 Ford F-150, we will be installing the Putco Push-Up tie downs, part number P99901. First, we will go ahead and assemble the tie down off the truck. We will install the gasket onto the main body and insert the 2 bolts. Then, we will take the mushroom blocks and put them onto the bolts. Then, loosely screw on the bolt plate. To install the tie down, we will first remove the cover over the stake pocket.more
Watch Video6/29/2012 12:33:38 PM
Stromberg Carlson Tailgate Installation - 2011 Chevrolet Silverado- Video
Today on our 2011 Chevy Silverado, we'll be test fitting the Stromberg Carlson 100 Series 5th Wheel Tailgate with open design part # VGM-07-100. Before we can install our tailgate, we'll need to assemble the latches. To do this, we'll first remove the cotter pins and install the split rings under the latch. This will be your handle of sorts for the latch locks. Next we'll go ahead and take the machine screws and lock nuts and attach the latch assembly to the tailgate. You set right in the middle of adjustment points on the tailgate.more
Watch Video6/6/2012 11:53:11 AM
Stromberg Carlson Tailgate Installation - 2012 Ford F-150- Video
Today we have with this the 2012 Ford F150. We're going to show you how to install the Stromberg Carlson Vented 5th Wheel Tailgate, part # VG-04-100. The first thing we need to do is remove the OEM tailgate. We'll lower it partially, disconnect the cables and then move the door to about a 45-degree angle so that we can slide it off of its hinges. Next we'll take a latch assembly, put it into place on a tailgate and use the included hardware to install our latch. We'll repeat the same for the opposite side of the tailgate.more
Watch Video6/6/2012 11:52:48 AM
Truck Luggage Expedition Cargo System Review- Video
Today well be doing a review on part number TL-603 Truck Luggage Expedition Truck Bed Cargo management system for full-sized trucks. This system will provide 8 cubic feet of cargo storage space in a stylish way. It has a very durable polyester bag that will hold and organize your gear. It will mount anywhere along the rails of the bed without drilling and it has a black powder coat finish to resist rust and corrosion. The bag is constructed of 600-denier polyester. This will help to resist weather and harsh UV rays.more
Watch Video4/10/2012 2:10:39 PM
Thule Flat Top Carrier on a Truck Luggage Expedition Cargo System Review- Video
Today well be installing the Thule Universal Flattop part number TH92725 on our Truck Luggage Cargo management system. Now weve already pre-fitted the ski rack platform part number TL-606 onto our cargo management system. Now all we need to do is fit the snow sport carrier onto it. Well take the carrier, set it on top of the crossbar and bring the rubber coated metal strap around and tighten it down using the gray knob on the one side of the clamp. With our front carrier secured to the platform, well simply move to the rear carrier and repeat the same process as we did with the front. With both carriers installed, we can now load our skis and snowboards.more
Watch Video4/10/2012 2:08:32 PM
Truck Luggage Expedition Cargo System Installation- Video
Were gonna be installing part number TL-603 the Truck Luggage Expedition Truck Bed Cargo Management System. This part no. will cover all full size trucks and has the capacity of 8 cubic feet. For this review we went ahead and removed everything from the box and laid it out for you so that you can see exactly what it should come with.All right! First of all, what were gonna do is to unfold the bag and turn it inside out. We'll then take the 2 plastic inserts, slide them in to the bag itself. They go in from the outside, slide in to place.more
Watch Video4/2/2012 5:32:50 AM
Highland Truck Bed Accessories 9251600 Review- Video
Today we are going to review part no 9251600. This are the Highland Movable Tie-Down Anchors for truck and trailer side rails. This anchors will allow you to hook your rachet straps on other tie-downs to these anchor points. These will clamp to the side rails or your trailer or truck bed. They do install quickly and easily and you can position them anywhere you want along the rails. They do use an easy clamp-on installation.more
Watch Video3/8/2012 6:00:03 PM
Stromberg Carlson Tailgate Installation - 2011 Chevrolet Silverado- Video
Today on our 2011 Chevrolet Silverado, we'll be installing the Stromberg Carlson Louvered 5th-Wheel Tailgate, part number VGM-07-4000. And with that, we'll go ahead and start our installation. We'll go ahead and review the contents of the product. We have two cables, a set of keys for the tailgate, a plastic insert that will go with the rubber tailgate insert, two bolts, four wood screws, four machine screws, and four clips for the machine screws. There are also two side covers. And with that, we'll go ahead and start our installation.more
Watch Video3/5/2012 11:09:42 AM
HitchMate NetWerks BedBag Mesh Cargo Bag Review- Video
Today we are going to show you the HitchMate NetWerks BedBag from Heininger, part number HE4022. The NetWerks BedBag is a mesh cargo bag that attaches to your HitchMate cargo stabilizer bar. It helps keep small items organized in the bed of your truck and it keeps them from moving around. The wide, integrated handles make for quick and easy attachment, as well as grabbing and carrying. The bag measures 21 inches wide by 18 inches tall and is covered by a one year limited warranty. 0:31more
Watch Video4/18/2011 11:53:00 AM
HitchMate Cargo Stabilizer Bar Review- Video
Today we are going to show you the HitchMate cargo stabilizer bar for full-size pickups, part number HE4016. Pickup truck beds are great because they offer plenty of storage space for hauling your gear. Unfortunately, sometimes that gear can slide around and move around inside of the bed. The cargo stabilizer bar is going to allow us to secure that gear and keep it from moving. The heavy-duty cargo bar is designed to expand across the width of your bed and help secure cargo and keep it from moving around. The ratcheting handle is easy to use and secure. The large sturdy rubber feet tightly grip the walls of the bed of your truck without leaving scuffs or scratches. And it can adjust from 59 to 73 inches. It is also covered by a one year limited warranty. 0:45more
Watch Video4/18/2011 11:16:14 AM
HitchMate StabiLoad Support for Cargo Stabilizer Bars Review- Video
Today we are going to show you the HitchMate StabiLoad support for cargo stabilizer bars, part number HE4017. The StabiLoad support is designed to attach to HitchMate cargo stabilizer bars and prevents your load from moving side to side behind the bar. It is compatible with both the full size and compact size cargo stabilizer bars, part numbers HE4016 and HE4015. Like the cargo stabilizer bars, the StabiLoad support is covered by a one year limited warranty. To install the StabiLoad support, all we have to do is set it on top of our cargo stabilizer bar, slide it against our load and use the set screws to clamp it down tight. Once we have it clamped down tight, our cooler cannot go anywhere. And that does it for the HitchMate StabiLoad support for cargo stabilizer bars, part number HE4017.more
Watch Video4/11/2011 10:31:40 AM
Bestop Retractable Tie-Downs for BestRail Channel System Review- Video
Today we are going to review part number B42794 from Bestop. This is their BestRail retractable tie down. First, remove any uprights you have on your vehicle in the position that you want. We have a ladder rack on this particular vehicle so we will push that forward and get it out of the way for now to get a better view of what is going on. :18more
Watch Video3/23/2010 3:54:47 PM
Easy Retriever Telescoping Pole with Hook Review- Video
Today we are going to show you part number 50710 the easy retriever. What we have here is a tool that can easily reach into the back of your pickup truck or any other place that is inaccessible or just out of arms reach. Kind of a handy tool to keep in the back of your truck. We will go ahead and show you how it works. It has a real easy telescopic design. Basically give it a little bit of a twist and it is ready to go to work. To show you an example on how to use it you can just reach into the back of your truck here. :22more
Watch Video12/30/2009 11:23:53 AM
Rail Kit Installation - 2004 Ford F-250- Video
All right, today on a 2004 Ford F-250 long bed, we are going to install BestRail kit part number 42730. One of the first things to do to prepare the rails is apply some camper tape to the bottom of them which is supplied with the kit. There are three rails we have to do this to. It is really simple. We will apply the tape to this edge here, over this gap, and onto this ridge right here. We will just work our way back all the way down. Repeat the same process on the other two rails. The next step is to slide three of the clamps into each one of the BestRail side rails. Using an 1/ 8 inch Allen wrench, we are going to install four of the 1/4 by 20 by 3/ 8 inch set screws in each of the corner brackets. Next we are going to go ahead and take the front BestRail and place it on the front rail of the truck bed.more
Watch Video10/7/2009 9:41:31 PM
Bestop BestRail Cargo Management System Review- Video
This is the BestRail Cargo Management System, and what this is is a very functional, flexible system that will allow you to add or subtract a lot of the accessories as needed. The BestRail System starts out here with a channel system that goes around the perimeter of the bed of the truck. And from that piece there, I can add or subtract depending on what my current needs are. The first thing that we have added today is the overhead rack system. And the overhead rack system comes with two parts. It allows me to go ahead and put lumber, ladders, etc., depending on what my needs are to carry out there. One big feature about this here is, we have a quick-release system. And these are ratchet-designed connectors here that hold the rear overhead rack in place. A nice thing I can do with that is I can either take it off in about 3 minutes, put it in my garage so I do not have the overhead rack. Or, I can go ahead and actually adjust this up anywhere here along this channel to give me the flexibility depending on what type of cargo I am carrying.more
Watch Video4/21/2009 5:59:22 PM
Hoppy Tailgate EasyLift Review- Video
Today we are going to show you part number 74211 from Hoppy. This is Hoppys Tailgate EasyLift. What this is, is a device that actually takes the weight off the tailgate and makes it easier to lift up and down. In most cases it will take up to 80 percent of the weight of the tailgate off your hands. It is actually pretty easy to install. As soon as you open it up you can see the instructions on what to do to install it. Basically you only have to drill two holes. One gets drilled into the tailgate itself and the other gets drilled into the truck bed itself. Most of the time on a tailgate you take two arms and you have got to really kind of push and shove it up in there. With the EasyLift it actually does not require that much effort at all. You can do it easily one-handed while probably carrying something in that arm, too. And also, when you let it down, it does not really flop down all that hard it actually has a controlled descent. And again, it just makes it smooth going up into the bed when you close it. And there you have it for part number 74211 from Hoppy, the Tailgate EasyLift.more
Watch Video12/17/2008 7:34:00 AM
Bully Clamp-On Truck Bed Hooks Review- Video
Today we are going to show you part number WTD-811 from Bully. This is their Clamp-on Truck Bed Hook. This is a simple little hook setup that you clamp onto the inside rail of your truck bed. And you can actually put it basically anywhere along the edge of the rail, as long as you have access to it - as long as you do not have a tonneau cover or something like that in the way. We will show you how it goes on. It is not too bad. You can put the plate anywhere on your truck bed that you like. The plate goes behind it. And then you take the knob here and it screws everything together, and this clamps behind the truck bed. And when you have it set exactly where you want it, then you can go ahead and just tighten it down.more
Watch Video12/16/2008 5:17:00 PM
Agricover Steel Access Storage Pockets Review- Video
Today we are going to show you part number A60070 from Agricover. This is their Access Storage Pocket. All right, what we have here are storage pockets that mount to the inside of the fender wells and go back to the back pillar by the tailgate. The material that they are made out of is galvanized steel. We will show you a couple of benefits of having this device in your truck. What is also nice about this product is it also works with the Easy Retriever from the same company. And it has two notches built into the pockets to help store it when you are not using it. And we are going to show you how it works. And there are two sections - one here, and one here. And you can also use this to keep light-duty cargo from sliding around a little bit, too.more
Watch Video9/20/2008 1:10:43 AM
Agricover Access Storage Pocket Review- Video
Today we are going to show you part number A60085 from Agricover. What we have here is the Access Storage Pocket. The storage pockets actually install within the well itself and go back toward the tailgate and not up on one of the pillars there. As you can see here, we have them laying in their respective positions. Also, what is nice about these storage pockets is they will work in conjunction with the Easy Retriever, and that part number is 50710. And we will show you how they work together. It has two little notches in it to lay your Easy Retriever in. So you can store light-duty materials in there with the tailgate up, and you also have two notches available for that purpose - one here, and one here.more
Watch Video9/19/2008 8:09:26 PM
Today we are going to show you part number A50710 the Easy Retriever. What we have here is a tool that can easily reach in the back of your pick up truck or any other area that is inaccessible or is just out of arms reach. Kind of handy little tool to keep in the back of your truck. We will go ahead and show you how it works. It has a real easy telescopic design. Basically you just give it a little bit of the twist and it is ready to go to work. To show an example on how to use it, you can just reach in the back of your truck here especially if you have a cover that is hard to take on or off. Just use it and you just grab it and pull your objects out, within easy reach. Also it would be handy for people that have limited mobility as well. That would probably be the biggest help. There you have it for part number A50710 the easy retriever.more
Watch Video9/10/2008 5:10:33 PM
Master Lock Premium Spring Clamp Tie Down with Strap Trap Review- Video
These are their 6 feet long by 1 inch wide spring clamp tie down with strap traps. The Master Lock strap tie downs offer a convenient upgrade to standard tie downs. It actually has a bungee cord and toggle feature that clenches around excess straps and keeps it in place so it is not flying around while you are going down the road. All the tie down straps include the monster weave webbing and razor coat abrasion resistant protection, this adds to the durability and its strength. The medium duty spring clamps and ratchet tie downs both feature the S hooks with retaining clips to give piece of mind while you are going down the road. The capacities of these tie downs are 1,200 pounds breaking strength, but its actual safe load limit is 400 pounds. Next we will install them on an anchor point and show how the clamp comes into use. Basically how were going to demonstrate this is we will start at one point on the pickup and go to the other side to tie off. You see that snap hook right there keeps it from coming apart. Now we will go over to the other side and tie it down and show you how the storage for the other strap works. Once you tie it down, take your excess and bundle it up, put it through this loop right here, and cinch it down. This will not be flapping around in the breeze. There you have it for part # 3062DAT from Master Lock, their 6 foot long by 1 inch wide spring clamp tie downs with the strap trap. This package contains a quantity of four.more
Watch Video8/7/2008 2:44:12 PM
Bully Truck Bed Tie Down Clamps Review- Video
This is a nice device that clamps onto any position along the bed of your truck to allow you to tie down virtually at any point on your truck. These clamp onto the actual inside lip of the truck bed and you can use this inside camper shells and a lot of tonneau covers too. We will go ahead and install one here and show you how it works. We will stick it inside our bed rail here, you want the clamp open, put it up in there, and make sure it goes up as far as possible. We will get this out of our way, and then there is a bolt at the bottom here which we will tighten up by hand and we will use a ratchet to tighten it up the rest of the way. There you have it, an instant tie down point. There you have it for part # WTD-823 the stainless steel truck clamp. more
Watch Video8/7/2008 9:51:31 AM
Bully Pop Up Tie Down Review- Video
This is a really neat little device that installs in the stake bed pocket of your pickup truck and when you are not using it stays completely flat. So actually this will work pretty well with some of the tonneau covers out there. This also works well with bed rail caps which you will see when we do an install on a vehicle with some plastic bed rail caps on the vehicle. We will go ahead and install this into the pocket on the bed rail here. You set it the way you want it and you simply tighten down the screws. There you have it, it is completely installed. Now with the flip of a switch it will be ready to tie down what you have in the back of your truck. To retract it, just simply push it back down into place. There you have it for part # WTD-810, the Bully pop-up truck hooks. more
Watch Video8/7/2008 9:50:28 AM
Truck Bed Stake Pocket Chrome Anchor Points Review- Video
This device fits into the stake pockets of your truck bed, youve probably seen this before, its a common design. They have added one nice feature to this product, the toggle bolt at the bottom is a much heavier duty model than the previous ones. It requires no tools to install and well show that by installing one. Well squeeze it together to get through the top there, this rubber block here will help center it in the truck. Then you just push it into place and make sure you have it nice and level, and tighten down your top half. You dont have to over torque it, just get it nice and snug maybe a turn after that. Now youre set, and youre ready to tie down your cargo. This part comes in a chrome finish to resist rust and corrosion. There you have it for part # 92509, the truck bed stake pocket chrome covered anchor points. more
Watch Video8/6/2008 1:13:31 PM
