Titan Hydraulic Trailer Brake Installation- Video
All right, today on this old trailer, we're going to install the hydraulic brake assembly, part number T2351100. Now, we're going to start off our install to hub our _ inaudible 0:00:12 removed so we can show how to remove the vacuum plate. First off, we'll go ahead and disconnect the hydraulic line behind it. We're going to use a wrench to undo the fitting and remove the line. We're going to take the line and point it upward to help keep the fluid in the line. Next, we'll go ahead and unbolt the old vacuum plate.more
Watch Video1/2/2013 10:52:34 AM
TruRyde Electric Brake Assembly Installation- Video
Today were going to install part number TRBK10E01 from TruRyde. This is their Electric Trailer Brake for Left Hand Side. Were going to start off our install with the idler hub already removed from the trailer. This trailer previously did not have brakes so were going to add brakes to the trailer. Now if we add brakes to this trailer axle due to the fact that it has a brake flange already installed located here. The brake is very to install, Ill just make sure the mag is pointing at the bottom.more
Watch Video9/21/2012 2:05:36 PM
Titan Trailer Brakes T4489600 Review- Video
Today were going to review part #: T4489600. This is the Titan, the Galphorite free backing hydraulic trailer brake assembly for the left hand side of your trailer. This drum brake assembly has a galphorite plating which will deliver superior corrosion protection. The backing plate and the shoe levers are sealed with a permanently bonded electro coat primer, then theres a second coat of rugged acrylic which is applied to the backing plate which makes it virtually rustproof. This is a good application for a marine boat application. The wheel cylinders are treated with a hot black oxide and the internal components are zinc plated and use the stainless steel springs.more
Watch Video5/31/2012 12:23:19 PM
Titan Trailer Brakes T4489500 Review- Video
Today were going to review part #: T4489500. This is the Titan Galphorite free backing hydraulic trailer brake assembly for the right hand side of your trailer. This drum brake assembly will have a galphorite plating which will deliver superior corrosion protection. The backing plate and the shoe levers are sealed with permanently bonded electro coat primer. Has a second coat of rugged acrylic which is applied to the backing plate which makes it virtually rustproof. The wheel cylinders are treated with a hot black oxide, the internal components are zinc plated and it has stainless steel springs.more
Watch Video5/31/2012 12:21:22 PM
Titan Trailer Brakes T4202800 Review- Video
Today were going to review part #: T4202800. This is the Titan free backing hydraulic trailer brake assembly for a right hand side of your trailer. This is a black painted drum brake assembly that has a free backing design which will let you reverse without your trailer brakes being activated. It is designed for use with hydraulic brake actuators that do not include the reverse lockouts. This is a right hand assembly which is the passenger side and the way you can tell that is the shorter shoe will face the front of the trailer, the larger shoe will always face the back of the trailer and the size of this brake assembly is a 12 inch by 2 inch and the way you measure that is the diameter is 12 inches from shoe to shoe. The 2 inch would mean the width of the pad, should be 2 inches.more
Watch Video5/31/2012 12:19:13 PM
Dexter Trailer Brakes 23-106 Review- Video
Today were going to review part #: 23-106, this is the Dexter 12 inch electric brake assembly for the right hand side of your trailer. This brake assembly is a size 12 inch by 2 inch and the way we do that measurement is the 12 inch would indicate the width of the brake shoe is what we measure here is 12 inches diameter. The 2 inch would indicate the width which is two inches of the brake shoe. This brake assembly when paired with a left hand assembly will be rater for 6000lbs axles. This brake assembly does use a five bolt mounting pattern, so what you need to do when you check you axle on your trailer, you want to check the brake mounting flange to make sure that it is a five bolt mounting flange. This is an electric brake assembly so there are two wires that will need to be connected.more
Watch Video5/31/2012 12:17:16 PM
Dexter Trailer Brakes 23-459 Review- Video
Today were going to review part number 23-459. This is the Dexter 12 inch Nev-R-Adjust Electric Brake Assembly for theright hand side. This assembly is a 12 by 2 brake assembly and the way you would measure that is the overall diameter of theshoes would be 12 inches and the width of the pad itself will be 2 inches. This is the right hand side which is the passengerside. When this assembly is paired with the left hand side it will fit on trailers that have axles with a maximum capacity of6,000 pounds. It does usually 12 inch hub and drum assemblies, and this does use the 5 hole mounting bolt pattern so youneed to check your brake mounting flange on your axle of your trailer to make sure it has the 5 hole mounting pattern.It also has the 2 wire leads, one is for ground, one is for the power or the brake feed.more
Watch Video5/25/2012 11:18:48 AM
Dexter Trailer Brakes 23-458 Review- Video
Today we're going to review part number 23-458. This is the Dexter 12inch Nev-R-Adjust Electric Brake Assembly. This is for the left hand sideor the driver side. This is a size 12" x 2" brake assembly. The way youwould measure that is the 12 inch would be the diameter of the brake shoeswhich is 12 inches and then the width of the brake shoe would be two inches.And this assembly when paired with the similar right hand side would beused on axles with a maximum of a 6,000 pound capacity for the pairassemblies. They do use a 12 inch hub and drum and it does use the five holemounting flange.more
Watch Video5/25/2012 11:17:00 AM
Titan Trailer Brakes T4423500 Review- Video
Today we are going to review part number T4423500. This is the ten-inch Titan Alpha right free backing hydraulic trailer brake assembly for the left hand side. This is drum brake assembly, which will provide superior protection from corrosion and it will let you reverse without actuating because of the free backing. This is designed for use with hydraulic brake actuators that do not include reverse lockouts. This will fit most 13-inch, 14-inch and 15-inch wheels. This assembly does have alpha right plating, which deliver superior corrosion protection.more
Watch Video5/22/2012 7:21:00 AM
Titan Trailer Brakes T4071600 Review- Video
Today we are going to review part number T4071600. This is the Titan free backing hydraulic ten-inch trailer brake assembly for the left hand side, which is the drivers side. This is assembly has a black painted finish and this free backing design which will let you reverse your trailer with the brakes being activated. It is designed for use with surge style trailer brake actuators that do not include reverse lockouts. This will fit most 13-inch, 14-inch and 15-inch wheels. This one if the left hand assembly and the easiest way to determine that is the smaller shoe will face the front of the trailer and the larger shoe, will face the rear of the trailer.more
Watch Video5/22/2012 7:19:00 AM
Titan Trailer Brakes T4071500 Review- Video
Today we are going to review part number T4071500. This is the Titan free backing hydraulic ten-inch trailer brake assembly for the right hand side, which is the passenger side. This is a black painted drum brake assembly. Itll let you reverse your brakes in your trailer without actually hitting the brakes. This is designed for use with hydraulic brake actuators that do not include reverse lockouts. This will fit most 13-inch, 14-inch and 15-inch wheels.more
Watch Video5/22/2012 7:17:16 AM
Dexter Trailer Brakes 23-469 Review- Video
Today, were going to review part number 23-469. This is the Dexter 10-inch Nev-R Adjust Electric Brake Assembly. This is for the right hand side or the passengers side. This brake assembly is a 10-inch by 2-1/4-inch right hand brake assembly. No way you would measure that because the overall diameter is 10 inches and the width of it would be 2-1/4 inches. This right hand assembly when paired with a left hand assembly will give you a 3500-pound capacity for the pair.more
Watch Video5/21/2012 1:18:57 PM
Dexter Trailer Brakes 23-468 Review- Video
Today, were going to review part number 23-468. This is the Dexter 10-inch Nev-R Adjust Electric Brake Assembly for the left hand side. This Dexter assembly is a 10-inch by 2-1/4-inch left hand brake assembly and a way to measure that is if you go across the diameter of the of the shoes it should be 10 inches, and then if you measure the width it would be 2-1/4 inches. This assembly when paired with a right hand side assembly will give you a 3500-pound weight capacity for the pair. This does use 10-inch hub and drum assemblies and this brake assembly does include the mounting studs. The nuts and washers would have to be purchased separately and Ill give you the dimension of that mounting studs.more
Watch Video5/21/2012 1:17:10 PM
Dexter Trailer Brakes 23-27 Review- Video
Today we are going to review part number 23-27. This is the Dexter ten-inch electric brake assembly for the right hand side. This electric brake assembly will measure ten inches by 2-1/4 and the way that is measured is the diameter of the shoes across. Its ten inches and the width of the shoe will be 2-1/4. This is passenger side brake assembly, which is the right hand side, and the way you can tell that is the shorter shoe will face the front of the trailer and the longer shoe will face the rear of the trailer. When this assembly is paired with a left hand side assembly, itll be rated for an axle 235 pounds.more
Watch Video5/21/2012 7:17:11 AM
Kodiak Trailer Disc Brake Kit Installation- Video
Ten is a boat trailer were going to do a Kodiak disc brake install part number K2HR35D. Before you kept put this conversion kit on, double check to make sure the coupler at the front of your trailer is ready for disc brake use. Sometimes surge brake couplers arent designed for disc brakes. Now were going to start off with our trailer actual strip down it previously had drum brakes on it so we take off the hub and we take off the drum brake. We also pull the brake line out of the way. Were going to point up all the way so that it wont drain all the fluid.more
Watch Video12/21/2011 8:10:21 AM
Titan 10" Right Hand Uni-Servo Hydraulic Trailer Brakes Review- Video
Today were looking at the Titan 10 inch hydraulic brake assembly, part number t4445300. This is the right hand side and the way we tell this is by looking at the shoe lining. The leading shoe will be smaller than the rear shoe. This particular assembly is a uni servo which means it has one wheel cylinder and one piston that will push out against the brake shoe creating a wedge effect in our hub drum assembly. To measure our assembly, to get our width, we see that its 10 inches across the linings. The shoe thickness is 2 and .more
Watch Video12/8/2011 12:02:32 PM
Titan 10" Right Hand Hydraulic Trailer Brakes Review- Video
Today were looking at the Titan 10 inch hydraulic brake assembly part number t4423400. This setup is for the right hand side, we can tell this by looking at the brake shoe lining. Our forward shoe is going to be smaller than the rear or primary shoe. This is our single servo setup which means it has one wheel cylinder and one wheel cylinder piston which will push out against the shoes and create a wedge effect inside the braking drum. This assembly mounts on our 4 bolt flange setup where the holes are pre drilled through the backing plate. They will mount easily onto your 4 stud flange setup.more
Watch Video12/8/2011 12:02:32 PM
Titan Galvanized 10" Right Hand Hydraulic Trailer Brakes Review- Video
Today were looking at the Titan 10 inch hydraulic brake assembly, part number t4522800. This setup is for the right hand side. We can tell this is by looking at the shoe linings as our forward shoe is going to be smaller than the rear shoe lining or primary shoe. This is a single servo setup which means it has one wheel cylinder and one wheel cylinder piston which pushes out against our brake shoe creating a wedge effect inside the brake drum. Our assembly is setup on a galvanized backing plate for minimal corrosion. This is a good marine application.more
Watch Video12/8/2011 12:02:32 PM
Titan 10" Left Hand Trailer Brakes Review- Video
Today were looking at the Titan hydraulic trailer brake assembly part number t1878800. This setup is for the right hand side. The reason we know this is for the right hand side is because our leading shoe will always be smaller than the trailing shoe or primary. This is a single servo setup which means that the wheel cylinder has one piston which will come out and press against the shoes creating a wedge effect inside of our drum to create the braking surfaces. This setup comes with a one year warranty and when coupled with the left hand side will create up to 3750 pounds of braking capacity. To know the width of our shoes our setup we can measure across the linings and see that its 10 inches.more
Watch Video12/8/2011 12:02:32 PM
Titan 12" Left Hand Hydraulic Trailer Brakes Review- Video
Today were looking at the Titan hydraulic brake assembly part number t4202900. This assembly is setup for the left hand side. The way we can tell this is by looking at the brake shoe lining. The forward shoe is going to setup smaller than the rear or primary shoe. This assembly is a single servo system which means it has one wheel cylinder and one wheel cylinder piston that pushes out against the forward brake shoe lining creating a wedge effect inside the brake drum. Our initial setup we use the star wheel adjuster to adjust the brake shoes out to the brake drum creating a light drag and then as the brake shoe linings wear, we can remove the grommet in the backing plate to continuously adjust the star wheel keeping the nice even braking.more
Watch Video12/8/2011 12:02:32 PM
Titan Galvanized 10" Left Hand Hydraulic Trailer Brakes Review- Video
Today were looking at the Titan 10 inch hydraulic brake assembly, part number t4522900. This setup is for the left hand side we can tell this is by looking at the brake shoe lining. The forward shoe is smaller than the rear or primary shoe.This is a single servo system which has one wheel cylinder and one wheel cylinder piston to push out against the brake shoe creating a wedge effect inside the brake drum.Our setup is on a galvanized backing plate for minimal corrosion. Well also bolt onto a 4 bolt flange stud on your axle. When you initially setup your assembly to your hub drum, you use a star wheel adjuster to adjust the linings out to create a light drag on the hub drum and then as the brake shoe linings wear, we can remove the grommet and adjust the star wheel as needed to keep the nice even braking. To measure our assembly take our tape measure and go across the linings and see we have a 10 inch by 2 inch shoe linings making this application fit a 10 and 2 inch hub drum assembly.more
Watch Video12/8/2011 12:02:32 PM
Titan 12" Left Hand Trailer Brakes Review- Video
Today were looking at the Titan 10 inch hydraulic brake assembly, part number t2351100. This assembly is setup for the left hand side and the way we tell this is by looking at the shoe lining. The forward shoe will be smaller than the rear shoe or primary. This is a single servo setup which means it has one wheel cylinder with one piston pushes out against our brake linings this will then create a wedge effect inside the brake drum assembly to create a nice even braking setup. This setup will also deliver 20 percent braking in reverse. When mounting its setup for a 5 bolt flange style, has pre drilled holes to the backing plate to mount up to your axle .more
Watch Video12/8/2011 12:02:32 PM
Dexter 7" x 1-3/4" Right Hand Hydraulic Trailer Brakes Review- Video
Today were going to take a look at the Dexter 7 inch hydraulic brake assembly part number 23-399. This assembly is a hydraulic brake assembly with a single servo meaning it has one piston that comes out of our wheel cylinder, pressing the shoe linings out against our drum surface. Couple this right hand side with the left hand side and its got a 2500 pound braking capacity. The reason we know this is the right hand side is because the leading shoe will always be smaller than the trailing shoe. The reason we know this is a 7 inch brake setup is you can measure across the shoe linings and see that its 7 inches.We measure the width of the shoe linings, well see its 1 and , so we have a 7 inch by 1 and inch setup. The installation is setup on a 4 bolt flange, you can see the heads of the stud go through the backing plate and come out the back, those mount to your flange on your axle.more
Watch Video12/8/2011 12:02:31 PM
Dexter 10" x 2-1/4" Right Hand Hydraulic Trailer Brakes Review- Video
Today, we're looking at the Dexter 10" Hydraulic Brake Assembly, part number 23-313. This setup is for the right-hand side. And the way we tell it is by this configuration, the forward shoe lining be thinner or smaller than the rear shoe lining or your primary shoe. This is a single servo setup, which means it has one wheel cylinder and one piston that pushes out against the shoes and they'll create a wedge effect inside the brake hub drum assembly. Couple this assembly with the left-hand side and the pair will create 3,500 pounds in braking capacity. To give the measurement of our assembly, we'll simply measure across the linings and see it is a 10" width.more
Watch Video12/8/2011 12:02:31 PM
Dexter 10" x 2-1/4" Left Hand Hydraulic Trailer Brakes Review- Video
Today, we're looking at the Dexter 10" Hydraulic Brake Assembly, part number 23-312. This assembly is for the left-hand side. We can tell this by looking at the shoe lining. The leading shoe will be smaller than the rear or primary shoe. This particular setup is also a single servo with one wheel cylinder and piston that will push out against this shoe lining, creating a wedge effect inside the hub drum assembly. This will give us our braking.more
Watch Video12/8/2011 12:02:31 PM
Demco Galvanized 10" Left Hand Trailer Brakes Review- Video
Today were looking at the Demco 10 inch marine brake assembly part number 40716. This assembly is setup for the left hand side and we can tell this by looking at the brake shoe assembly linings, the forward shoe is will be be smaller than the rear or primary shoe. This is a single servo setup which means it has one wheel cylinder with one wheel cylinder piston that will push out against the brake shoe creating a wedge braking effect inside the hub drum. This setup mounts on a 4 bolt flange with the holes pre drilled into the backing plate. To mount on your 4 bolt flange with studs. On your initial application, well use the star wheel adjuster to adjust the brake shoe linings out to the brake drum creating a light drag, then as the brake shoe linings wear, we can simply remove the grommet in the backing plate and adjust the star wheel out to create that nice even braking.more
Watch Video12/8/2011 6:02:31 AM
Dexter 7" x 1-3/4" Left Hand Hydraulic Trailer Brakes Review- Video
Today were looking at the Dexter 7 inch hydraulic brake assembly part number 23-398. This assembly is for the left hand side. The reason we can tell its for the left hand side is because the front shoe will always be smaller than the rear shoe. This is a single servo setup which means it has a wheel cylinder with one piston that will push out against your forward shoe and create a wedging effect against the primary shoe inside the brake drum when applied. When you couple this left hand side with the right hand side, the pair will create up to 2500 pounds in braking capacity. To tell what shoe and hub drum assembly you have, you measure across the linings and see that its 7 inches.more
Watch Video12/8/2011 6:02:31 AM
Demco Galvanized 10" Right Hand Trailer Brakes Review- Video
Today, we're looking at the Demco Galvanized 10" Marine Brake Assembly, part number 18787. This assembly is set up for the right-hand side. The way we can tell this by looking at the shoe lining itself. The forward shoe is going to be smaller than the rear shoe lining or primary shoe lining. This is a single servo setup, which means there is one wheel cylinder and one piston that comes out, creating a wedge effect inside the hub drum assembly. To tell the measurement of our shoe for setup, we simply measure across the linings and see that we get 10" in our width.more
Watch Video12/8/2011 6:02:26 AM
Dexter 12" x 2" Hydraulic Trailer Brakes Review- Video
Today were looking at the Dexter hydraulic brake assembly, part number 23-343. This assembly is setup for the right hand side, we can tell this by looking at the forward brake shoe is smaller than the rear brake shoe or primary shoe. This is a single servo setup which means it has one wheel cylinder and one wheel cylinder piston that pushes out against a brake shoe creating a wedge effect inside the brake drum. Our assembly is setup on a 5 bolt mounting flange for the backing plate theres pre drilled holes to sit on your 5 bolt studded axle flange. On your initial setup you use the star wheel adjuster to adjust the shoe linings out to create a light drag on the brake drum, then as the shoe linings wear, we can remove the grommet in the backing plate and adjust the star wheel out as needed to give the nice even braking. To measure our braking assembly, go across the linings, we have 12 inch and the thickness of the lining is 2 inch, therefore this assembly will fit a 12 inch by 2 inch hub drum assembly.more
Watch Video12/8/2011 12:02:31 AM
Today were looking at the Demco 10 inch marine brake assembly, part number 40715. This is the right hand side and the way we tell this is by looking at the brake shoe linings. The forward shoe will be smaller than the rear shoe or primary shoe. This is our single servo setup which means the wheel cylinder will have piston that will push out against the brake shoe creating a wedge effect inside the brake drum. This assembly mounts on a 4 bolt flange which is already pre drilled in the backing plate to sit on top of your 4 bolt flange studs. As initial setup, we use a star wheel adjuster to adjust the brake shoe linings out to create a light drag on the brake drum, then as the brake shoe linings wear, we can remove the grommet in the backing plate to adjust the star wheel out to keep that nice even braking.more
Watch Video12/8/2011 12:02:31 AM
Demco Galvanized 10" Left Hand Trailer Brakes Review- Video
Today were looking at the Demco galvanized marine brake assembly part number 18788. This particular assembly is for the left hand side, we can tell this by looking at the shoe lining. The lining in the forward shoe is smaller than the lining on the rear shoe or primary. This means we have the left hand side. Couple this with the right hand side and it will create 3500 pounds in braking capacity. This is a single Inaudible 00:00:28 setup so we have one wheel cylinder and one piston that well push out against our shoe to create our pressure needed to create braking.more
Watch Video12/8/2011 12:02:31 AM
Titan 10" Right Hand Trailer Brakes Review- Video
Today were looking at the Titan hydraulic trailer brake assembly part number t1878700. This is a single servo assembly, it has one wheel cylinder with one piston that comes out against our brake shoes to create a wedge effect inside the brake drum. To measure the brake shoes, measure across the linings to see that its a 10 inch setup for a 10 inch drum. The thickness or width of our shoes is 2 and , so for our hub drum assembly to fit, well need a 10 inch by 2 inch braking system. The mounting plate, 4 bolt assembly, you want to double check your flange assembly to make sure you have the 4 bolt stuff setup. When initially installing your brake assembly, youll need to use a star wheel adjuster to push the brake shoes out to your hub drum assembly so you create an even braking surface.So you need to adjust that star wheel out into the backing plate.more
Watch Video12/7/2011 6:02:32 PM
Tekonsha 12" Right Hand Electric Trailer Brakes Review- Video
Today we are going to take a look at Tekonshas self adjusting electric brake assembly, 12 for right hand side, part number 54801-007. The brake assembly is 12 by 2. We will measure across the shoes, and theres our 12 mark. Then we will measure the width of the shoe, and theres our 2 mark. When paired up with the assembly for the left hand side these brakes are good for axels up to 7,000 pounds, they are also covered by a limited one year warranty. The brake assembly uses a 5 bolt mounting pattern.more
Watch Video11/28/2011 6:30:25 AM
Tekonsha 12" Left Hand Electric Trailer Brakes Review- Video
Today we have Tekonshas self-adjusting 12-inch brake assembly for left hand side, part number 54801-008. This is a 12-inch by 2-inch brake assembly. Well measure the diameter across the shoes and theres our 12-inch figure. Then well measure the width of the shoe and theres our 2-inch mark. When paired up with the assembly for the right hand side, these brakes are good for axles rated at 7000 pounds. The assembly is also covered by a limited one-year warranty.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Right Hand Nev-R-Adjust Electric Trailer Brakes Review- Video
Today we're going to show you Dexter's 12" Nev-R-Adjust Electric Brake Assembly for right-hand side, part number 23-465. This is a 12" x 2" break assembly. We will measure the diameter across the shoes and there is a 12" figure. Then we'll measure the width of the shoes and there is our 2" mark. When paired up with the assembly for the left-hand side, these brakes are good for axles, weighted up to 7,000 pounds. The assembly uses the 5-bolt brake mounting pattern.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12-1/4" x 3-3/8" Left Hand Electric Trailer Brakes Review- Video
Today, we're going to show you Dexter Self-Adjusting Electric Brake Assembly for Left-Hand Side, part number 23-434. This is a 12-1/4" by 3-3/8" brake assembly. We'll measure the diameter across the shoes and there is 12-1/4". And we'll measure the width of the shoes and there is 3-3/8". When paired up with the right-hand side brake assembly, these brakes are good for use on trailer axles rated at 8,000 or 9,000 pounds. It uses a 4 bolt mounting pattern.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Right Hand Electric Trailer Brakes Review- Video
Today we are going to take a look at Dexters 12 Electric Brake Assembly for right hand side, part number 23-106-09. This is a 12 by 2 brake assembly, to measure the diameter across the shoes and theres the 12 mark. Then youll measure the width of the shoe, and theres the 2 figure. When paired up with the left hand side assembly these brakes are good for axels rated up to 6,000 pounds. It could be used with one of two mounting patterns. These smaller holes are for five bolt, and the larger holes with the type 2 at the bottom are for the Alco or Hays 4 bolt pattern.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12-1/4" x 2-1/2" Right Hand Electric Trailer Brakes Review- Video
Today, we're going to take a look at Dexter's 12-1/4" x 2-1/2" Electric Trailer Brake Assembly for the Right-Hand Side, part number 23-429. This is a 12-1/4" x 2-1/2" assembly. We'll measure across the brake shoes and that's where we get our 12-1/4". Then we'll measure the width of the brake shoes and there is our 2-1/2". This brake assembly comes with a pair of wire leads and it doesn't matter which you connect as your ground or your brake feed as long as you have a good electrical connection. It uses a 4 bolt mounting pattern.more
Watch Video11/28/2011 6:30:25 AM
Tekonsha 10" Right Hand Electric Trailer Brakes Review- Video
Today were going to take a look at Tekonshas electric brake assembly 10-inch, self-adjusting for the right hand side, part number 54801-005. This is a 10-inch by 2 -inch brake assembly. We can measure the diameter across this shoe, and theres our 10-inch figure. Then well measure the width of the shoe, and theres our 2 . When paired up with the brake assembly for the left hand side, these brakes are good for trailer axles that are rated up to 3500 pounds. Its going to mount using these four bolts that are already pressed into the assembly.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Right Hand 7K Electric Trailer Brakes Review- Video
Today were going to take a look at the 12 Electric Brake Assembly for right hand side, part number 23-181. This is a 12 by 2 brake assembly. Well measure the diameter across the shoes, and theres our 12 mark. Then we will measure the width of the shoe itself, and theres our 2 figure. This brake assembly when paired with the left hand side is good for axels rated up to 7,000 pounds. It mounts using a 5 bolt mounting pattern, so you will want to check your axel and make sure its got the 5 bolt mount.more
Watch Video11/28/2011 6:30:25 AM
Tekonsha 10" Left Hand Electric Trailer Brakes Review- Video
54801-006more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Left Hand Nev-R-Adjust Electric Trailer Brakes Review- Video
Today, we're going to look at Dexter's 12" Nev-R-Adjust Electric Brake Assembly for Left-Hand Side, part number 23-464. This is a 12" x 2" electric assembly. Measure the diameter across the shoes, and there is a 12" figure. Then we'll measure the width of the shoes, and there is a 2" figure. When paired up with the assembly for the right-hand side, these brakes are weighted for axles at 7,000 pounds. The assembly mounts on a 5-bolt pattern.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Left Hand Electric Trailer Brakes Review- Video
Today we're going to show you the 12" Electric Brake Assembly for Left-Hand Side, part number 23-105. This is a 12" x 2" brake assembly. We measured the diameter across the shoes and there's our 12". Then we measure the width of the shoe and there's our 2" figure. When paired up with the right-hand side assembly, these brakes are good for trailer axles rated up to 6,000 pounds. The assembly mounts on a 5 bolt mounting pattern.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Left Hand 7K Electric Trailer Brakes Review- Video
Today we are going to take a look at the 12 Electric Brake Assembly for the left hand side, part number 23-180. This is a 12 by 2 electric brake assembly. Measure of the diameter across the shoe, and theres our 12 number. Then we will measure the width of the shoe, and thats where we get our 2 figure. The brake assembly when compared to the right hand side is good for trailer axels up to 7,000 pounds. It utilizes the 5 bolt mounting pattern, so you want to make sure that your trailer axel has the same mounting configuration.more
Watch Video11/28/2011 6:30:25 AM
Dexter 12" Left Hand 6K Electric Trailer Brakes Review- Video
Today we are going to take a look at Dexters 12 Electric Brake Assembly left hand side, part number 3-105-09. This is a 12 by 2 assembly, we will measure the diameter across the shoes, and theres our 12 figure. Then we can measure the width of the shoe, and theres our 2 mark. When paired up with the right hand side assembly these brakes are good for axels rated up to 6,000 pounds. There are 2 different mounting configurations predrilled into the assembly back, you can either use the 5 bolt assembly with the smaller bolt holes, or you can use the Alco, or Hays 4 bolt assembly with the larger bolt holes. So check your axel to see if you have either the 5 bolt or the 4 bolt off set Alco / Hays pattern.more
Watch Video11/28/2011 6:30:24 AM
Hayes 12" x 2" Left Hand Electric Trailer Brakes Review- Video
Today, we're going to take a look at Hayes/AL-KO 12" x 2" Electric Brake Assembly for the Left-Hand Side, part number 185100. This is a 12" x 2" electric brake assembly. We'll measure the diameter across the shoes and there is a 12" mark. And then we'll measure the width of the shoes, there is a 2" mark. When paired up with the assembly for the right-hand side, these brakes are good for axles that are weighted up to 7,000 pounds. You can mount this assembly using one of two patterns.more
Watch Video11/28/2011 6:30:20 AM
Hayes 12" x 2" Right Hand Electric Trailer Brakes Review- Video
Show you the Hayes/AL-KO 12" x 2" Electric Brake Assemblies for the right-hand side, part number 185150. This is a 12" x 2" assembly. So measure the diameter across the shoe and there is our 12". And then we'll measure the width of the shoe and there is our 2" mark. When paired up with the assembly for the left-hand side, these brakes are good for axles rated up to 7,000 pounds. There are two mounting patterns that you can use with this assembly.more
Watch Video11/28/2011 6:17:47 AM
Dexter 12-1/4" x 3-3/8" Right Hand Electric Trailer Brakes Review- Video
Today, we're going to show you Dexter Self-Adjusting Electric Trailer Brake Assembly for the Right-Hand Side, part number 23-451. This is a 12-1/4" by 3-3/8" brake assembly. We'll measure the diameter across the shoes and there is 12-1/4" x 3-3/8" brake assembly. We'll measure the diameter across the shoes and there is 12-1/2" mark. Then we will measure the width of the shoe and that is 3-3/8". When paired up with the left-hand side, these brakes are good for axles rated at 9,000 and 10,000 pounds.more
Watch Video11/28/2011 12:30:25 AM
TruRyde 12" Left Hand Electric Trailer Brakes Review- Video
Today we are going to look at the TruRyde Electric Brake Assembly 12 for the left hand side, part number TRBK12E01. This is a 12 by 2 brake assembly. We can measure across the brake shoes for our 12 figure, and then we will measure the width of the shoes, and thats where we get our 2. This brake assembly when paired with the opposite side are good for axels up to 7,000 pounds. Its also covered by a 1 year limited warranty. It uses a 5 stud mounting pattern, so you need to check the axel on your trailer to make sure that you have the correct pattern.more
Watch Video11/25/2011 12:00:23 PM
