Roadmaster Stop Light Switch Kit Installation - 2012 Jeep Liberty- Video
Watch Video5/20/2013 9:25:14 AM
Roadmaster InvisiBrake Supplemental Braking System Installation - 2010 Hyundai Elantra- Video
Today on our 2010, Hyundai Elantra, we will be installing the Roadmaster InvisiBrake, supplemental braking system; part number: RM-8700. Now, before beginning our installation, weve already gone ahead and removed the rear seat, the drivers seat and both the front trim, as well as the rear door trim. Weve already gone ahead and removed the left front tire, as well as the left front inner fender well. This will allow us access to the main wiring harness where it passes through into the passenger compartment. Now, as you can see here, weve got our InvisiBrake box set onto the floor of the vehicle, underneath where the drivers seat would be. Well find a good location, making sure that the bolts that we are going to use to hold the box down go through the floor and dont go through anything else underneath the vehicle.more
Watch Video4/12/2013 10:49:29 AM
Blue Ox Patriot Proportional Braking System Installation - 2013 Ford C-Max- Video
All right today on this 2013 Ford C-Max, were going to install part number BRK2012 from Blue Ox. This is the Blue Ox Patriot radio frequency portable breaking system. First thing were going to do is find a location to run our breakaway switch wire from the inside to the outside. Were going to pull back the carpet on the inside of the vehicle behind the pedals and were going to locate a spot just below the grommet inaudible 00:00:27 steering column. Its going to be about one inch below and off to the left hand side of center. All right, well go ahead and drill out inaudible 00:00:35 first and then well go ahead and enlarge our drill bit size up to 11/16.more
Watch Video3/25/2013 2:10:21 PM
Blue Ox Patriot Proportional Braking System Installation - 2004 Mini Cooper- Video
Alright today on this 2004 Mini Cooper were going to install Part #BRK2012 Blue Ox. This is the Patriot Radio Frequency Portable Braking System.First off to begin our install we are going to have to run a cable from the inside of the vehicle to the outside of the vehicle. This will be for the break-away switch. Now the break-away switch itself was previously installed on the vehicle at the same time when the base plate was installed. So we dont have to worry about that part, well go ahead and start running our wire. Now there is a small opening in the bumper that we will use to route our wire.more
Watch Video3/22/2013 12:38:19 PM
Roadmaster InvisiBrake Supplemental Braking System Installation - 2001 Chevrolet Tahoe- Video
All right. Today, on this 2001 Chevrolet Tahoe, we're going to install part number RM-8700 from Road Master, and this is a brake kit. Okay. To start off the install, we remove the threshold and also the kick plate by the compartment brake. We lift up the trim panels in the back. We're going to route our cylinder next to the driver seat, and we will attach it later on to the metal bracket that's near a console.more
Watch Video3/4/2013 8:45:07 AM
Roadmaster InvisiBrake Supplemental Braking System Installation - 2002 Jeep Liberty- Video
Today on this 2002 Jeep Liberty Sport were going to install product number RM-8700 from Roadmaster. This is their InvisiBrake Kit. Alright, first thing we do is figure out where we're going to install pulley and then air cylinder and plus this cable will activate it so we want to keep the bins as little as possible in the cable. So were actually going to hide it underneath the threshold going across here and also by the back seat. So we'll just pop up this threshold here. We're going to lay out our air cylinder in this area right here.more
Watch Video2/2/2012 3:42:38 PM
