Westin Safari Light Bar Installation - 2000 Jeep Grand Cherokee- Video
Watch Video5/22/2013 2:20:32 PM
Roadmaster Base Plate Installation - 2012 Honda Fit- Video
Watch Video5/22/2013 2:07:13 PM
Trailer Hitch Installation - 1999 Jeep Cherokee - Curt- Video
Watch Video5/21/2013 10:43:21 AM
Titan Uni-Servo Hydraulic Trailer Brake Assembly Installation- Video
Watch Video5/20/2013 9:47:27 AM
Trailer Hitch Installation - 2008 Kia Sorento - Hidden Hitch- Video
Today on our 2008 Kia Sorento we'll be installing Hidden Hitch, part number 87425. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier. The center of the hitch pin hole is even with the outermost edge of the bumper. The top of the receiver tube opening to the ground is 14 inches. Now we'll go ahead with installation.more
Watch Video5/17/2013 4:05:58 PM
Trailer Hitch Installation - 2013 Nissan Xterra - Curt- Video
Today on our 2013 Nissan Xterra we're going to be installing the Curt Hitch, part number 13514. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a few measurements to help you choose some accessories for your hitch such as a ball mount, bicycle rack or cargo carrier.From the center of the hitch pin hole to the edge of the bumper is approximately a half inch past the edge of the bumper. From the top of the opening on the hitch to the ground is approximately 19-1/2 inches. Now we'll go ahead and install our hitch. To begin with we went ahead and already removed the spare tire so we'd have a little more working room.more
Watch Video5/17/2013 3:54:54 PM
Trailer Hitch Installation - 2013 Nissan Murano - Curt- Video
Today on our 2013 Nissan Murano we'll be installing the Curt Hitch, part number 13577. This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube opening to the ground is 15-1/4 inches. This will assist your selecting accessories such as a ball mount, a bike rack or cargo carrier.more
Watch Video5/17/2013 3:50:54 PM
Trailer Hitch Installation - 2008 Kia Sorento - Draw-Tite- Video
Today on our 2008 Kia Sorento we'll be installing the Draw-Tite hitch, part number 75516. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier.The center of the hitch pin hole is even with the outermost edge of the bumper. The top of the receiver tube opening to the ground is 14 inches. Now we'll go ahead with installation. To begin our install we'll first point out the attachment points.more
Watch Video5/17/2013 3:37:23 PM
Trailer Hitch Installation - 2013 Nissan Murano - Hidden Hitch- Video
Today on our 2013 Nissan Murano we'll be installing the Hidden Hitch, part number 87486. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 5-1/2 inches.From the top of the receiver tube to the ground is 15-1/2 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier. Now we'll go ahead with installation.more
Watch Video5/16/2013 11:29:10 AM
Trailer Hitch Installation - 2013 Nissan Murano - Draw-Tite- Video
Today on our 2013 Nissan Murano we'll be installing the Draw-Tite Hitch, part number 75647. This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 5-1/2 inches. From the top of the receiver tube to the ground is 15-1/2 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier.Now we'll go ahead with installation.more
Watch Video5/16/2013 11:26:56 AM
Trailer Hitch Installation - 2005 Kia Sorento - Curt- Video
Today on our 2008 Kia Sorento we'll be installing the Curt Hitch, part number c13513. This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier.From the center of the hitch pin hole to the outermost edge of the bumper is 1-1/2 inches. From the top of the receiver tube opening to the ground is 14-1/2 inches. Now let's go ahead with the installation. To begin our install we'll first point out the attachment points.more
Watch Video5/16/2013 10:36:24 AM
Trailer Hitch Installation - 2010 Toyota Tacoma - Curt- Video
Today on our 2010 Toyota Tacoma we're going to install part number 13323 from Curt. This is what the hitch looks like when it's installed on a vehicle. Next we'll give you some measurements to help you out in selecting some accessories such as a bar mount, a bicycle rack or a cargo carrier. From top of receiver opening down to the ground will be about 19 1/2 inches and from the center of the hitch pin hole to the edge of the bumper will be about three and a half inches. Now I'll go ahead and show you how the hitch is installed.First Im going to go ahead and remove the bumper. Before we can go that we'll go ahead and loosen up the electrical connections for the license plate lights.more
Watch Video5/3/2013 12:33:58 PM
Trailer Hitch Installation - 2009 Chevrolet Silverado - Hidden Hitch- Video
Today on this 2009 Chevrolet Silverado were going to install part number 87186 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From top of receiver opening down to the ground will be about 21 and a half inches, from the center of the hitch pin hole to the edge of the bumper will be about three inches. Now well go ahead and show you how the hitch is installed. First thing were going to do is go ahead and point out the attachment points on the vehicle.more
Watch Video4/25/2013 8:24:45 AM
Trailer Hitch Installation - 2009 Chevrolet Silverado - Draw-Tite- Video
Today on this 2009 Chevrolet Silverado were going to install part number 75521 from Draw-Tite. This is what the hitch looks like when installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From top of receiver opening down to the ground will be about 21 and a half-inches, from the center of the hitch pin hole to the edge of the bumper will be about three inches. Now well go ahead and show you how the hitch is installed. First thing were going to do is go ahead and locate the two bolts at the end of the frame we have to remove.more
Watch Video4/25/2013 8:23:50 AM
Trailer Hitch Installation - 2008 Honda CR-V - Hidden Hitch- Video
Today, on our 2008 Honda CRV, we'll be installing Hidden Hitch, part number 87440. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is two inches. From the top of the receiver tube opening to the ground is 14 inches. This will assist you in selecting accessories such as a ball mount, a bike rack, or a cargo carrier.Now, let's go ahead with installation.more
Watch Video4/19/2013 12:46:36 PM
Trailer Hitch Installation - 2008 Honda CR-V - Draw-Tite- Video
Today, on our 2008 Honda CRV, we'll be installing the Draw-Tite hitch, part number 75547. This is what our hitch will look like once it's installed. Next, we're going to go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is two inches. From the top of the receiver tube opening to the ground is 14 inches. This will assist you in selecting accessories such as the ball mount, a bike rack or a cargo carrier.Now, let's go ahead with installation.more
Watch Video4/19/2013 12:46:13 PM
Trailer Hitch Installation - 2008 Honda CR-V - Curt- Video
Today on our 2008 Honda CRV, we're installing the Curt hitch, part number 13555. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 2-1/2". From the top of the receiving tube opening to the ground is 14". This will assist you selecting accessories such as a ball mount, a bike rack, or a cargo carrier.more
Watch Video4/19/2013 12:45:53 PM
Trailer Hitch Installation - 2006 Honda Pilot - Draw-Tite- Video
All right, today on this 2006 Honda Pilot, we're going to install part number 75599 from Draw-Tite. All right, this is what the hitch looks like when it's installed on a vehicle. Next, we'll give you some measurements to help you in selecting some accessories, such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about 18-1/2". From the center of the hitch pin hole to the edge of the bumper will be about 3-1/4". Now I'll go ahead and show you how the hitch is installed.more
Watch Video4/16/2013 8:59:59 AM
Wheel Masters Tools WM6700 Review- Video
Today were going to take a look at the Wheel Masters Level Master trailer bubble level number WM6700. This easy-to-read bubble level helps you level your fifth-wheel trailer or camper when parking or using your landing gear. The large scale assists with side-to-side leveling with each mark here indicating one inch of blocking. You have a smaller scale that helps with front-to-rear leveling. Once you have your level attached, there is an adjustment screw here you can see that here in the back, once youre attached and level then you can work your adjustment screw to get your front-to-back level where it needs to be. Its easily visible from your truck cab and it wont leak or freeze.more
Watch Video4/15/2013 10:15:40 AM
Trailer Hitch Installation - 2006 Honda Pilot - Curt- Video
All right, today on this 2006 Honda Pilot, we're going to install part number 13328 from Curt. All right, this is what the hitch looks like when it's installed on the vehicle. Next, we'll give you some measurements that will help you out when selecting some accessories, such as a ball mount, a bicycle rack, or a cargo carrier. From top of receiver opening down to the ground will be about 18". And from the center of the hitch pin hole to the edge of the bumper will be about 4". Now I'll go ahead and show you how the hitch is installed.more
Watch Video4/15/2013 9:23:07 AM
Trailer Hitch Installation - 2009 Ford Flex - Curt- Video
Today on our 2009 Ford Flex, well be installing the Curt Trailer Hitch, part number C13110. Now before we begin our installation, here are a few measurements to help you when selecting accessories such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper measures 4 inches and from the top of the receiver tube to the ground is 13 inches. Now lets go ahead with our install. To begin our installation, well need to lower the exhaust by removing these three isolators. One here behind the muffler, one here just in front of the rear axle and one here about the middle of the vehicle.more
Watch Video4/12/2013 10:50:30 AM
Trailer Hitch Installation - 2013 Toyota FJ Cruiser - Hidden Hitch- Video
Today on our 2013 Toyota FJ Cruiser, well be installing hidden hitch part number 87412. This is what our hitch will look like once it is installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole, the outermost edge of the rear mounted spare tire is 8-3/4 inches. From the top of the receiver tube opening to the ground is 18-1/2 inches. This will assist you in selecting accessories such as a ball mount, a bike rack, or cargo carrier.more
Watch Video4/5/2013 1:16:20 PM
Trailer Hitch Installation - 2013 Toyota FJ Cruiser - Draw-Tite- Video
Today, on our 2013 Toyota FJ Cruiser we will be installing the Draw-Tite hitch part #75461. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. On the center of the hitch pin hole, the outermost edge of the rear-mounted spare tire is eight and three-quarter inches. From the top of the receiver tube opening to the ground is eighteen and one-half inches. This will assist you with selecting accessories such as a ball mount, a bike rack or a cargo carrier.more
Watch Video4/5/2013 11:00:53 AM
Trailer Hitch Installation - 2012 Ford Taurus - Curt- Video
Today on this 2012 Ford Taurus, we're going to install part number 13552 from Curt. This is what the hitch looks like once installed on the car. Next, we'll give you some measurements that will help you out in selecting some accessories. From the top of the receiver opening down the ground will be 12-1/2 inches and from the center of the hitch pin hole to the edge of the bumper will be 6 inches. Now, we'll go ahead and show you how the hitch is installed. The first thing we're going to do is go ahead and put a piece of strap to help support the exhaust when we lower it.more
Watch Video4/1/2013 10:29:36 AM
Trailer Hitch Installation - 2002 Toyota Avalon - Draw-Tite- Video
Today on our 2002 Toyota Avalon, well be installing the Draw-Tite Hitch, part number 36293. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is five inches. From the top of the receiver tube opening to the ground is ten inches. This will assist you with selecting accessories such as a bike rack or cargo carrier.more
Watch Video3/28/2013 2:41:06 PM
Trailer Hitch Installation - 2013 Volkswagen Beetle - Curt- Video
All right, today on this 2013 Volkswagon Beetle, we're going to install part number C11260 from Curt. This is what the hitch looks like once installed on the vehicle. Next, we'll give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 9-1/2", and from the center of the hitch pin hole to the edge of the bumper will be about 4-3/4". All right, now we'll go ahead and show you how the hitch is installed. All right, first thing we're going to do is go ahed and go ahead and show the mounting locations for the hitch.more
Watch Video3/26/2013 2:02:11 PM
Trailer Hitch Installation - 2006 Mercury Grand Marquis - Draw-Tite- Video
Today on this 2006 Mercury Grand Marquis, were going to install part number 24526 from Draw-Tite.Alright, this is what the hitch looks like once installed on the vehicle. Next we'll give you some measurements thatll help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From top of receiver opening down to the ground will be about 11 and a quarter inches and from the center of the hitch pin hole to the edge of the bumper will be about five and three-quarter inches.Now we'll go ahead and show you how the hitch is installed. The first thing were going to do is at the very end of the frame, is measure back one-half an inch and make a mark. Next, we'll take the hitch and hold it up in position and line it up with that mark. Now we'll go ahead and support the hitch.more
Watch Video3/26/2013 10:20:34 AM
Trailer Hitch Installation - 1996 Nissan Maxima - Draw-Tite- Video
Today on this 1996 Nissan Maxima, were going to install part number 24686 from Draw-Tite. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 12 and 3/4 inches, and from the center of the hitch pinhole to the edge of the bumper will be about four and a half inches. Now well go ahead and show you how the hitch is installed. The first thing were going to do is go ahead and get inside the trunk area of the vehicle and remove the spare tire.more
Watch Video3/25/2013 3:29:17 PM
Trailer Hitch Installation - 2005 Nissan Armada - Curt- Video
Today on this 2005 Nissan Armada, were going to install part number 13188 from Curt. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 21 inches and from the center of the hitch pinhole to the edge of the bumper will be about 1 inches. Now well go ahead and show you how the hitch is installed. First thing were going to do is go ahead and show attachment points on the frame. There are two weld nuts at the very end of the frame and one going towards the front.more
Watch Video3/25/2013 2:11:23 PM
Blue Ox Base Plate Installation - 2010 Jeep Liberty- Video
Today on our 2010 Jeep Liberty well be installing the Blue Ox Base Plate Kit with removable arms, part number bx1976. To begin our installation, well go ahead and turn the wheel all the way to the drivers side exposing the inner wheel well here on the passenger side. Here well remove three push pin tabs and two rivets. To remove the push pin tabs, well take a flat bladed screwdriver, pry the center of the tab out and then remove the entire tab. For the push pin rivets, you can attempt to cut off the head of the rivet, or like well do, well go ahead and drill the center out and then just pull out the rest of the rivet. Next well go ahead and pull the wheel liner back exposing a bolt up underneath the wheel liner that will need to be removed.more
Watch Video3/25/2013 2:10:05 PM
Trailer Hitch Installation - 2008 Kia Sportage - Curt- Video
Today on our 2008 Kia Sportage, we'll be installing the Curt Hitch, part number C12126. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch, such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole, to the outermost edge of the bumper is six inches. From the top of the receiver tube opening to the ground is 12 and three-quarter inches. Let's go ahead with installation.more
Watch Video3/25/2013 11:40:58 AM
Trailer Hitch Installation - 2012 Nissan Murano - Hidden Hitch- Video
Today on our 2012 Nissan Murano well be installing the Hidden Hitch, part number 87486. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4 inches. From the top of the inside of the receiver tube opening down to the ground is 15 inches. This will assist you with selecting accessories such as a ball mount, a bike rack or a cargo carrier.more
Watch Video3/19/2013 8:23:30 AM
Trailer Hitch Installation - 2012 Nissan Murano - Curt- Video
Today, on our 2012 Nissan Murano, we'll be installing the Curt Hitch, Part Number 13577. This is what our hitch to look like once it's installed.Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. The center of the hitch pinhole to the outermost edge of the bumper is 4-1/2 inches. From the top of the inside of the receiver tube opening to the ground is 14-1/2 inches. This will assist you in selecting accessories such as the ball mount, a bike rack or a cargo carrier. Now, let's go ahead with the installation.more
Watch Video3/19/2013 8:23:21 AM
Trailer Hitch Installation - 2012 Honda CR-V - Hidden Hitch- Video
Watch Video3/18/2013 10:59:16 AM
Trailer Hitch Installation - 2010 Nissan Rogue - Curt- Video
Today on this 2010 Nissan Rouge, were going to install part number C12247 from Curt.This is what the hitch looks like when its installed on a vehicle. Next well give you some measurements to help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From top of receiver opening down to the ground is going to be 14 and a quarter inches. From center of the hitch pin hole to outer edge of the bumper is going to be about 7 and a quarter inches. Now well go ahead and show you how the hitch is installed.First thing were going to do is go over to the passenger side frame rail and remove the tie down bracket. The two bolts in the bottom and two bolts on the side.more
Watch Video3/15/2013 1:04:52 PM
Trailer Hitch Installation - 2010 Nissan Rogue - Hidden Hitch- Video
Today on this 2010 Nissan Rogue were going to install part number 87457 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 14 inches. And, from the center of the hitch pin hole to the edge of the bumper will be about 7 inches. Now, well go ahead and show you how the hitch is installed.more
Watch Video3/15/2013 1:04:45 PM
Trailer Hitch Installation - 2010 Nissan Rogue - Draw-Tite- Video
Today on this 2010 Nissan Rogue were going to install part number 75606 from Draw-tite. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 14 inches. And, from the center of the hitch pin hole to the edge of the bumper will be about 7 inches. Now, well go ahead and show you how the hitch is installed.more
Watch Video3/15/2013 1:04:36 PM
Trailer Hitch Installation - 2010 Nissan Rogue - Curt- Video
Today on this 2010 Nissan Rogue were going to install part number 13185 from Curt. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 14 inches. And, from the center of the hitch pin hole to the edge of the bumper will be about 7 inches. Now, well go ahead and show you how the hitch is installed.more
Watch Video3/15/2013 1:04:26 PM
Trailer Hitch Installation - 2012 Nissan Frontier - Curt- Video
Today on this 2012 Nissan Frontier, were going to install part number 13241 from Curt. All right this is what the hitch looks once its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about 18-3/4 and from the center of the hitch pin hole to the edge of the bumper will be around 3-1/4. Now well go ahead and show you how the hitch is installed.All right the first thing were going to do is go ahead and show you where the hitch will mount up to the frame. On each side of the frame close to the bumper will be three sets of threaded holes, well go ahead and point those out.more
Watch Video3/14/2013 7:37:03 AM
Trailer Hitch Installation - 2007 Chrysler 300 - Curt- Video
Today on our 2007 Chrysler 300, we will be installing Curt Hitch, part number C12240. Before we begin our installation, here are a few measurements to help you on selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch pin hole to the outer most part of the bumper is 7 inches. From the top of the receiver tube to the ground is 12 inches. Now lets go ahead with our install. Before we begin our installation, we will need to lower our exhaust. Well first put a safety strap underneath the vehicle to hold the exhaust while we undo the mounting location. On the two rear most isolators, we can go ahead and undo the bolts holding the isolators to the vehicle.more
Watch Video3/7/2013 3:23:59 AM
Tru-Flate Digital Tire Pressure Gauge Review- Video
Today well be showing you the operation of our Tru Flat digital tire pressure gauge with dual foot, part number L17-547. This versatile digital tire gauge makes it easier than ever to check your tire pressure. The large backlit display is easy to read. The tire gauge is designed to let you easily check tire pressure on almost any tire. It works between 10 PSI and 150 PSI. It will also read in four different units of measure: PSI, bar, KPA and KGF CM2.more
Watch Video3/1/2013 11:48:04 AM
Redline Aluminum Tread Plate Trailer Fender Installation- Video
Today on this old trailer were going to install part number J101733AT. This is a diamond plate aluminum fender. Our trailer has already had the previous fender removed and all we have to do is clean off the excess sealant that was around the fender. You can see how the trailer did have a blowout and the side of the trailer is damaged. The fender now is going to be a little bit shorter than the original, but it will still fit in the same place. Well go ahead and hold the fender up and line it up with the original line so we can make our marks in our inside of our fender.more
Watch Video3/1/2013 10:16:34 AM
Trailer Hitch Installation - 2010 Infiniti FX35 - Curt- Video
Today on this 2010 Infiniti FX35, were going to install part number 13554 from Curt. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin opening to the edge of the bumper is going to be five inches and from the top of the receiver opening down to the ground is going to be 15 inches. All right, now well go ahead and show you how the hitch is installed. First thing you do is remove the splash guards from the driver and passenger sides of the vehicle.more
Watch Video2/25/2013 9:22:35 AM
Trailer Hitch Installation - 2009 Kia Optima - Curt- Video
Today on our 2009 Kia Optima, we'll be installing the CURT hitch, part number c11351. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch-pin hole to the outermost edge of the bumper is six inches. From the top of the receiver tube opening to the ground is 9 1/4 inches. This will assist you in selecting accessories such as a bike rack or cargo carrier.more
Watch Video2/15/2013 2:20:12 PM
Trailer Hitch Installation - 2009 Kia Optima - Hidden Hitch- Video
Today on our 2009 Kia Optima, we'll be installing the Hidden Hitch, Part Number 60848. This is what our hitch to look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6-3/4 inches. From the top of the receiver tube opening to the ground is 10-1/4 inches. This will help us in selecting accessories such as the ball mount, a bike rack or a cargo carrier.more
Watch Video2/15/2013 2:18:55 PM
Trailer Hitch Installation - 2009 Kia Optima - Draw-Tite- Video
Today on our 2009 Kia Optima, we'll be installing the Draw-Tite Hitch, Part Number 24778. This is what our hitch to look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting new accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6-3/4 inches. From the top of the receiver tube opening to the ground is 10-1/4 inches. This will help us in selecting accessories such as the ball mount, a bike rack or a cargo carrier.more
Watch Video2/15/2013 2:18:49 PM
Trailer Hitch Installation - 2005 Chrysler 300 - Curt- Video
Today on our 2005 Chrysler 300, we'll be installing the CURT hitch, part number 13465. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch-pin hole to the outermost edge of the bumper is 6 3/4 inches. From the top of the receiver tube opening to the ground will be 10 1/4 inches. This will assist you selecting accessories, such as a drawbar, a bike rack, or cargo carrier.more
Watch Video2/15/2013 2:18:29 PM
Trailer Hitch Installation - 2009 Chevrolet Traverse - Curt- Video
Today on our 2009 Chevy Traverse, well be installing a Curt Hitch part number 13424. The first step of our install well be removing the rear fascia door. To remove the fascia door, well simply take the tabs and turn them 45 degrees and then pull down on the fascia door unlocking it from its position. Then well need to go ahead and lower the exhaust. Before we lower the exhaust, well put a safety strap underneath so that we can control the rated descent. Now to remove the exhaust hangers from the metal brackets, well simply spray them down with some spray lubricant and then use our pry bar to remove the rubber isolator from the metal hanger.Then well go ahead and use the safety strap to safely lower the exhaust out of the way and gain access to the frame rail where well have a total of four attachment points, two on each side.more
Watch Video2/8/2013 4:03:59 PM
Roadmaster Base Plate Installation - 2012 Chevrolet Sonic- Video
Today in our 2012 Chevrolet Sonic, well be installing the Roadmaster EZ2 Base Plate Kit with Removable Arms, part number 523173-1. Note, weve already gone ahead and raised the vehicle and removed the front tires. However, it is not necessary. It can make it easier in the removal and reassembly of the front clip. Well remove the six pushpin fasteners and four bolts going across the top of the front of the clip underneath the hood. Next, were going to go ahead and move underneath the vehicle, where we will remove seven Torx bit fasteners, one plastic pushpin fastener, and two bolts so that we can go ahead and disconnect the front clip from the lower fascia and remove the lower panel.more
Watch Video2/8/2013 4:03:25 PM
