Pilot Automotive Hitch Covers CR-017F Review- Video
Today, were reviewing part number CR-017F from Pilot. This is a brake and tail light LED hitch cover with an officially licensed Ford logo. The logo will shine blue when its being used as a taillight, but when you apply your brakes, the log shines bright red. It fits both 1 1/4 and 2-inch trailer hitch receivers.First, lets turn the lights off and Ill show you how it shines. It comes with a four-pole plug, so that just connects to your existing four-pole. Weve got it plugged in today to a portable power source.more
Watch Video5/1/2013 2:20:05 PM
Pilot Automotive Hitch Covers CR-007XL Review- Video
Today, we're going to review Part Number CR-007XL. This is the Bully Light-Up Rectangular Trailer Hitch Receiver Cover and this fits 2-inch trailer hitch receivers. As you can see, this is made of a nice ABS plastic construction which is very durable and weather resistant. It is designed to slide into a two-inch trailer hitch receiver. It does have a wiring harness plug that'll plug into your existing four-way on your vehicle. Now, it does require, when you install it into your hitch receiver, it does require a pin and clip or a hitch lock, both of those are sold separately.more
Watch Video4/22/2013 11:16:27 AM
Pilot Automotive Hitch Covers CR-017 Review- Video
Today were going to review part number CR-017. This is the Pilot Oval LED brake light trailer hitch receiver cover. This cover will fit one and a quarter inch hitches and two inch size hitches. This hitch cover will illuminate when the running lights are on and it will brighten when the brake pedal is pressed. It will also blink when the turn signals are used.This light does use the LED lights which are brighter than a standard incandescent bulb and will last over 100,000 hours. It does have 12 total LED bulbs, three in the bottom row, six in the middle row and three on the top row.more
Watch Video3/15/2013 12:15:49 PM
Alfred Hitch Cover Hitch Covers 034092100805 Review- Video
Today were going to take a look at the UCLA Bruins two-inch Trailer Hitch Receiver Cover, number 034092100805. Whether its Bowl season or March Madness or youre an alum of the University of California at Los Angeles, you can show your school spirit with this UCLA hitch cover. The cover features the official UCLA athletics logo in true blue and gold weather hardened enamel fill. This covers durable construction and stylish look will show your support for the Bruins for years to come. Again, its designed for standard two-inch hitch receivers. Installation is very easy, it takes about 15 seconds.more
Watch Video12/28/2012 2:16:29 PM
Knockout Hitch Covers KD583H Review- Video
Today, well take a quick look at one of Knockouts trailer hitch covers, part number KD583H. On the face of this cover is the slogan Fear No Beer in black and gold writing. Its designed to fit 2-inch-by-2-inch trailer hitch receivers. Its made out of a high quality automotive grade ABS plastic.On the front, theres a polyurethane gel coating to help the face long lasting. The oval on the face has an overall length measurement of 5 inches wide and an overall height measurement of about 3-1/2 inches tall. Knockout covers this with a 90-day limited warranty.On the inside is a plastic spring clip thatll help retain the hitch cover inside your hitch.more
Watch Video8/6/2012 10:34:26 AM
Knockout Hitch Covers KD138H Review- Video
Today, were going to a quick look at one of Knockouts trailer hitch receiver covers, part number KD138H. This hitch cover is made out of a high quality automotive ABS plastic thats made from recycled material.Inside the tube is a plastic spring clip that will retain the cover inside your hitch. The tab on either side will stick into the hitch pinhole of the receiver holding the cover in the place. You can remove this spring and replace it with a traditional 5/8 hitch pin or even a hitch lock.On the face is the phrase Bad Girl in black letters over a silver background. The face is coated with a polyurethane that wont yellow, crack, or peel. This cover is made in the U.S.A.more
Watch Video8/6/2012 10:33:18 AM
DWD Plastics Hitch Covers 205713 Review- Video
Today, were going to take a quick look at the American flag trailer hitch receiver cover for 2-inch hitches from DWD, part number 205713. This hitch cover has a full color graphic of the American flag on the front. Its a poly resin face, so it has a bit of a shine to it. The body of the hitch cover is made of a high-impact polystyrene plastic. Its durable and weather resistant.The hitch cover will fit into your hitch and theres a plastic clip here that will spring in and hold the hitch cover into the hitch pinhole of the hitch. The cover will help keep dirt and grime from getting inside the hitch.more
Watch Video8/6/2012 10:17:37 AM
Reese Hitch Covers 86066 Review- Video
Today, were gonna review part number 86066. This is the Reese Dodge Ram LED Brake and Tail Light trailer Hitch Cover to fit 1-1/4 and 2-inch hitch receivers. This is an officially licensed 3D Dodge Ram logo, which will add a stylish touch to your vehicle. It uses red LED lights, which will light up to give your vehicles some flash and make it more visible as well as to alert other drivers to slow down or stop when you do. When plugged in, it has a low illumination, which will be used when youre using your tail lights and then it goes to a higher or brighter illumination when you apply your breaks or engage the hazard lights. It does use energy efficient LEDs, which are long lasting.more
Watch Video7/12/2012 10:21:55 AM
Reese Hitch Covers 86065 Review- Video
Today, were going to review part number 86065. This is the Reese Ford LED Brake and Tail Light Trailer Hitch Cover for 1-1/4 and-2-inch hitches. This is an officially licensed 3D Ford Logo, which will add a stylish touch to your vehicle. It does use red LEDs which will light up to give your vehicle some flash and make it more visible as well as to alert other drivers to slow down or stop when you do. It does have a low illumination while youre using your tail lights and higher brighter illumination when you brake or engage the hazard lights or your brake light. They do use an energy-efficient LED which are long lasting.more
Watch Video7/12/2012 10:20:25 AM
Reese Hitch Covers 86062 Review- Video
Today, were going to review part number 86062. This is the Reese Chevrolet LED Brake and Tail Light Trailer Hitch Cover. Fits 1-1/4 and 2-inch hitches. This is an officially licensed 3D Chevrolet Bowtie logo, which will add a stylish touch to your vehicle. On the inside of the logo are red LEDs which will light up to give your vehicle some flash and make it more visible as well as to alert other drivers to slow down or stop when you do. It has a low illumination while youre using your tail lights and its plugged in to your four-way, and it will have a high illumination when you brake or engage your hazard lights.more
Watch Video7/12/2012 10:19:04 AM
Reese Hitch Covers 86061 Review- Video
Today, were going to review part number 86061. This is the Reese GMC LED Brake and Tail Light Trailer Hitch Cover for 1-1/4 and 2-inch hitches. This is an officially licensed 3D GMC logo, which will add a stylish touch to your vehicle. It does use red LEDs which will light up to give your vehicle some flash and make it more visible, as well as to alert other drivers to slow down or stop when you do. When plugged in to your four-way, it will have a low illumination while using your tail lights and then a brighter, higher illumination when you break or engage the hazard lights. It does use energy efficient LEDs which are long lasting.more
Watch Video7/12/2012 10:17:15 AM
Knockout Silly Boys Jeeps R 4 Girls Hitch Cover Installation- Video
We're going to install a 2-inch hitch cover, part number KD567H. To install your hitch cover simply press on the locking tabs sliding the hitch cover into the receiver tube until the tabs line up with the hitch pin hole. Now, our hitch cover is locked in place. And that will do it for our hitch cover, part number KD567H.more
Watch Video5/10/2012 11:24:53 AM
Draw-Tite Rubber Hitch Cover Review- Video
Today we are going to show you the Draw-Tite rubber tube cover for 1-1/4 hitches, part number 2211. This is the basic rubber hitch cover that is designed to friction fit inside your Class I and Class II 1-1/4 hitches. It is friction fit so it does not require a pin and clip to hold it in place. It will help seal up your hitch receiver and prevent water from getting inside. To install the cover, all you have to do is push it inside your 1-1/4 hitch and push it all the way to the back so it is nice and snug. And that does it for the rubber tube cover for 1-1/4 inch hitches from Draw-Tite, part number 2211.more
Watch Video8/4/2011 10:39:54 AM
Texas Flag Trailer Hitch Cover Review- Video
Today we are going to show you the state of Texas Flag 2-Inch Receiver Hitch Cover, part number 034092101109. As you can see here, the tube cover itself is a depiction of the Texas flag. And this is an alloy material with enamel that has been put inlay into the shape itself. I will show you the back side of it. This comes with a foam gasket to help it fit on the receiver hitch a little bit tighter. It also comes with two different wire forms here. These wire forms adjust the tube cover to match different variants in the hitch pin. Some are farther back in the hitch tube than others. As you can see, there is only a short length here and a long length here. And you only use one at a time and they fit into these tabs sticking out. The tabs themselves have different lengths where the holes are. This tab here, if you can see, is towards the edge. And on this one over here, it is a little bit closer down towards the bottom. Use that in conjunction with the wire forms to get the best fit possible on your hitch.more
Watch Video12/1/2008 11:30:56 AM
Golf Club Trailer Hitch Cover and Lock Review- Video
Today we are going o be showing you part number CR-418. This is the Golf Club Stainless Steel Trailer Hitch Cover with an accompanying lock. Now, this fits both an 1-/14 and 2 inch hitches and it also has great random bushings to fir your hitch better. It also comes with its own lock to insure it is secure as you are traveling, to make sure nobody walks off with it. It is constructed from a rust proof stainless steel and includes a hitch pin and lock. It is designed to fit both an 1-1/4 and 2-inch trailer hitches. And the hitch cover face is 8 inches wide by 4 inches tall. This is for anybody that is a big fan of golf, who likes to show it off as you drive.more
Watch Video11/28/2008 4:23:28 AM
Brake Light Trailer Hitch Cover Review- Video
Today we are going to cover part number CR-007 from Bully. This is the Brake Light Trailer Hitch Receiver Cover for 2-inch receivers. This is your most basic lighted trailer hitch cover out there. It fits a 2-inch receiver only, and it has basically a red light in the back here that comes on when you hit your brake or your right-turn signal. And that is the only time it comes on. Again, it is a very basic unit. But it is always good to have an extra third brake light just for safety's sake. We will go ahead and install it on a vehicle and show you how it looks.more
Watch Video11/28/2008 3:12:54 AM
Waving American Flag Trailer Hitch Cover Review- Video
Today we are going to show you an American Flag Waving 2-Inch Hitch Receiver Cover, from Alfred. And this is part number 034092100201. As you can see here, it depicts an American flag in a waving position. And this fits only 2-inch receiver hitches. And it is constructed out of alloy material with an enamel inlay into the etching here to provide the colors. On the backside here, you can see the actual alloy material that it is made out of. It also comes with a gasket. What that does, it helps seal up the hitch tube cover and also provides a little bit of friction or something to press against for the wire forms as they are installed into the receiver hitch itself. And the wire forms themselves have two different lengths to facilitate installing a hitch cover, because sometimes a hitch pin in the end of the hitch itself has varying lengths, depending on that manufacturer. And on the tabs here, you can see that the pins have different heights, like say this one is towards the end and this one is towards the bottom. Again, it gives you better adjustment to make a proper fit on your hitch.more
Watch Video11/26/2008 12:01:26 PM
Dale Earnhardt Jr. NASCAR Trailer Hitch Cover Review- Video
Today we are going to show you part number CRN-8 from Bully. This is the Dale Earnhardt, Jr., Number 8 NASCAR Chrome Trailer Hitch Receiver Cover. The material that this tube cover is made out of is die-cast material, chrome, with Dale Earnhardt, Jr.s insignia Number 8 on there. This product will fit 2-inch and 1-1/4 inch receiver hitches. These pieces right here are what make it fit into a 1-1/4 inch receiver hitch. It also comes with a foam gasket to help give it a tight fit into the hitch. And on the tube cover itself, we have this one set up for a 2-inch receiver hitch, as you can see right here: the two plastic parts that go into the 2-inch part, and the foam gasket also.more
Watch Video11/26/2008 11:45:45 AM
Propeller Trailer Hitch Cover Review- Video
Today we are going to show you part number CR-402L from Bully. This is their 4-Blade Propeller Trailer Hitch Cover for 1-1/4 and 2 inch trailer hitches. It also has an LED stoplight on the back also. As you can see here, it is a 4-blade propeller and it spins freely in the wind. It is pretty neat. When you go down the road, it spins around and you look like you have a propeller on the back of your vehicle. And you can see, off to the side there are two other plastic parts. Those are parts that will allow you to use it in an 1-1/4 inch receiver hitch also. The foam gasket on the side helps make it a tight fit whenever possible and also helps keep out extra dust and corrosion from getting inside the hitch itself.more
Watch Video11/26/2008 11:39:47 AM
Maltese Trailer Hitch Cover Review- Video
Today we are going to cover part number CR-414, from Bully. And this is their Maltese Chrome Trailer Hitch Receiver Cover. This cover here, as you can see, has a Maltese cross and it works on 1-1/4 and 2 inch receiver hitches. This consists of die-cast construction with a chrome finish and it has plastic parts in the back to fit either 1-1/4 or 2 inch receiver. Off to the side here, we do have the pieces right here that do make it adaptable to an 1-1/4 inch receiver and a foam gasket. And the cross itself, we have a 2 inch version mounted up, with the plastic here and the foam gasket installed.more
Watch Video11/26/2008 11:21:19 AM
Harley-Davidson Trailer Hitch Cover Review- Video
Today we are going to show you the Harley-Davidson Trailer Hitch Cover, and this part number is HDHCY12. This is a high-end trailer hitch cover for your vehicle. It features embedded jewelry-quality cubic zirconium stones, as you can see, outlined around the edge of the emblem. This has been lab tested for weather- and corrosion-resistant construction. The post of this tube cover is made of stainless steel, and the face of it is chrome-plated solid brass. This tube cover also comes with various components to install on your vehicle for a perfect fit. We will get this tube cover ready to install. We will just take it out of the packaging here and flip it around. And these are the bushings. Again, you will use them according to your vehicle. We are going to use the thickest one, and it slides on in place, and then we will use the smallest one on top of it. And it uses any combination as long as it makes a nice, tight fit into your hitch.more
Watch Video11/21/2008 11:44:17 AM
Tailgater Trailer Hitch Cover Review- Video
Today we are going to show you part number 40171BLK from Alfred Hitch Cover. What we have here is the Official Tailgater hitch cover. It is a great little device, a perfect addition to any tailgating event. It is a pretty simple design. It installs into a 2-inch receiver clip. Use your standard pin and clip or locking pin and clip, and you can use it as a bottle opener. As you can see here we have the Official Tailgater and we also have this wire form here. And the wire form actually helps it stay in place. And you see it also has a foam gasket and another wire form installed. There are two different styles wire forms - depending on the hitch pin and the distance to the end of the hitch. It varies from manufacturers.more
Watch Video9/19/2008 8:17:18 AM
Duck Trailer Hitch Cover Review- Video
As you can see this part has a hunting theme to it for all you hunters out there. Well show you how this installs to the receiver hitch of your vehicle. As you can see it has a little spring clip in here, you simply push it together a little bit, and it slides right into your hitch. Once you have it started you simply push it all the way back and it locks into place. When you take it off you just push it in and pull it out, its a relatively simple device. What else you can do with this is replace the clip inside here with a deadbolt receiver lock, any 2 inch variety will work fine on this model. Its just a little extra security so no one walks off with it. There you have it for part # 202040, the duck hitch cover from DWD plastics.more
Watch Video7/28/2008 8:14:24 AM
