Front Mount Trailer Hitch Installation - 2011 GMC Sierra- Video
Watch Video12/28/2012 9:18:16 AM
Front Mount Trailer Hitch Installation - 2001 Toyota Tundra- Video
Today on our 2001 Toyota Tundra well be installing the Curt Front Mounted Hitch, part number 31180. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the front most edge of the bumper is two and three quarter inches. From the top of the receiver tube to the ground is 14 inches. First, before we can install the hitch, well need to remove the front tow hooks.more
Watch Video11/5/2012 1:24:18 PM
Front Mount Trailer Hitch Installation - 2006 Dodge Ram- Video
Today on our 2006 Dodge Ram 1500 we're going to install the Curt front mounted hitch part #: 31320. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the license plate is 3 and a half inches. From the top of the receiver tube to the ground is 12 and inches. This will assist you in selecting accessories, now lets go ahead with the installation. Before we can begin the installation well need to go ahead and take a notch out of the front air dam to allow for the hitch clearance.more
Watch Video4/24/2012 3:23:03 AM
Front Mount Trailer Hitch Installation - 2012 Toyota 4Runner- Video
Today on this 2012 Toyota 4Runner were going to install part number C31054 from Curt. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a winch mount or a skid plate. From the center of the hitch pins the outside edge of the bumper is going to be 4 inches and from the top of the receiver opening down to the ground will be 11-1/4 inches. Now well go ahead and show you how t he hitch is installed. The first thing we need to do to start our installation is to go ahead and remove the driver and passengers side underbody panels.more
Watch Video3/15/2012 11:28:48 AM
Front Mount Trailer Hitch Installation - 2010 Dodge Ram- Video
Today on this 2010 Dodge Ram 2500, were going to install part number c31015 from Curt. This is what it looks like when the hitch is installed on the vehicle. Next we will give you some measurements that will help you out when selecting some accessories. From the center of the pin hitch hole to the outside edge of the bumper is going to be 9-1/2, and from the top of the receiver tube down to the ground is going to be 13. Now I will go ahead and show you how the hitch is installed. Alright our first step we have to make a notch in an air dam at the bottom of the bumper.more
Watch Video11/11/2011 8:45:54 AM
Front Mount Trailer Hitch Installation - 2008 Ford F-350- Video
Today we are working on a 2008 Ford F-350. We will be installing a front mount hitch by Draw-Tite part number 65049. Here are a couple of measurements that will assist you with ing accessories for your new hitch such as a snow plow, a draw bar or a winch mount. From the center of the hitch pin hole to the outer-most point of the front bumper is 4-1/4 inches and from the top of the receiver tube to the ground is going to be 14-1/4 inches. Now let us go ahead with the installation. 0:28more
Watch Video9/19/2011 5:11:49 PM
Front Mount Trailer Hitch Installation - 2009 Ford F-250- Video
Today on this 2009 F-250 we will be installing the front hitch part number 65049. We are underneath the front of the vehicle here, and we are going to go ahead and point out the mounting location for the trailer hitch. We are actually looking at the passenger side frame rail on the outboard side and we have got a couple holes visible. If you look more forward towards the bumper side you will see a 9/ 16 size hole right there. That is going to provide our forward most attaching point for our trailer hitch. I do want to note on some of the newer model vehicles with four wheel drive. It has a bigger air dam here at the front and this air dam will need to be trimmed on those four wheel drive models. If you do need to trim the air dam just go ahead and give it a test fit and maybe take some dimension and go ahead and cut it before you get started. 00:40more
Watch Video10/28/2009 5:10:47 PM
Front Mount Trailer Hitch Installation - 2008 Chevy Silverado 2500 Heavy Duty- Video
Today on this 2008 Chevrolet Silverado 2500 Heavy Duty we are going to be installing front mount hitch part number 31109 from Curt. We are here looking at the passenger side frame rail. And you can see from the bottom we have got an existing bolt, an existing access hole, and then an existing regular sized hole as well. We are going to be fishing through the carried bolt block through this hole. We are going to pull it down into position using the fish wire that is provided with the installation kit. We are also going to be using this larger bolt here on the side of the frame. We are going to be removing it and replacing it with the new one that is provided in the installation kit. That is going to provide our vertical attachment point for the trailer hitch. more
Watch Video8/18/2009 7:57:43 AM
Front Mount Trailer Hitch Installation - 2007 Dodge Ram- Video
Today we are going to install part number 65046. This is a front-mount receiver hitch from Draw-Tite, and we are going to install this front-mount hitch on a 2007 Dodge Ram pickup truck. The hitch is going to mount to the bottom of the frame here. We are going to have to drill two holes out. It is also going to mount to this bottom bolt right here. What we are going to do first is go ahead and take these two bolts loose. They are connected by a strap on the other side, so we have to take the nuts off both sides. We are going to loosen these up, support the bumper, and then put the hitch on the lower bolts here. And then we will hang it by that side, and then we will do the same thing on the other side. We are only using one spacer plate because this truck has the tow hooks already in place. Make sure we put our bolt back in and then put our nut back into place. All right, we can go ahead and install the nut on the top bolt and snug that down.more
Watch Video6/15/2009 11:29:33 PM
Front Mount Trailer Hitch Installation - 1996 Jeep Wrangler- Video
Today we are going to install part number 65048, our front-mount hitch, and we are going to install this on a 1996 Jeep Wrangler. The next thing we will do is show you where the hitch resides on the front of the vehicle. Most of the time you expect it to sit on the bottom of here, but in the Jeep style, the way the frame is built, the actual hitch sits on top, and that is where it is going to ride. What is going to happen next is we are going to take out the hardware and use the existing bolt holes under the plastic tube. So we put our hitch on first and just lay it on the top as we trace around it. So that is where we are going to cut around the plastic and put it back on when we are done. This is going to be identical on both sides. So let us start disassembling and get the trim piece off.more
Watch Video5/21/2009 11:30:56 AM
Front Mount Trailer Hitch Installation - 2005 Toyota Tundra- Video
Today we are going to install part number 65031 from Draw-Tite, and we are going to install this on a 2005 Toyota Tundra pickup. To begin our install, let us take a few pieces off the vehicle. First off, this tow hook right here has to come off it will stay off. This skid plate right here, that will have to come off and stay off. And then this hook over here, this loop or tie-down has to come off, also. This bolt here and here and there are two back here that come out and allow the shield to come down. Next we will install the hitch on existing weld nuts. It is a good idea to have an extra set of hands because it is kind of heavy and kind of wide. Once we have the hitch installed by the factory bolts I am sorry, with the factory holes then we use the hitch as a template to drill out the last two remaining holes. All right, what we will do from here on out is, we will go ahead and snug the bolts down, lock the hitch into position, and we will start our drilling. The hitch will mark where our holes are going to be drilled at. Again, we will use it for a template. We will start off with a 1/4-inch drill bit to make a pilot hole, and then we will follow it up with a 1/2-inch bit. And this is the other one right here.more
Watch Video1/2/2009 3:24:02 AM
Front Mount Trailer Hitch Installation - 2008 Toyota FJ Cruiser- Video
Today we are going to install part number 31367 from Curt. We are going to install a front mounted hitch on a 2008 Toyota FJ Cruiser. To do our install the hitch mounts in 3 different places. One is right here where we are going to take this bolt out here. There are three nuts over here on the right side where we take out the lowest one on this side. The hitch also attaches to the tow loop here and they will be the same on both sides. Go ahead and break these loose. It would be a good idea to have one of these ratcheting wrenches, this makes life real easy on this install. Next we can install our hitch. One thing you have to do obviously get the arms up in here to match that, but also the tabs on the hitch have to fit over the tow hooks. It is a tight fit, you just have to wiggle it into place. At this point we can go ahead and re-install our hardware. more
Watch Video7/24/2008 8:14:58 AM
Front Mount Trailer Hitch Installation - 2007 Chevy Silverado 3500 HD- Video
Today we are going to show you an install on part number 65050. This is a front mount hitch and we are installing it on 07 Chevy Silverado 3500 HD. To begin our install we have to remove our license plate holder which is the square object in the center there. That has to come off and whats next is we have to cut a hole in the bumper so that the receiver can poke through. The plate is riveted on so we will have to drill out these rivets and just pop them off. What seems to work is grab the backside of the rivet with a pair of pliers and drill out the front and it comes right apart. Our next step is to start measuring so we can knock out our hole in the bumper. We are going to start with a common measurement. Basically we are going to start from this bolt right here. more
Watch Video7/22/2008 9:00:46 PM
Front Mount Trailer Hitch Installation - 2006 Ford F150- Video
Today we are going to install part number 65043 from Draw Tite and we are going to install this on a 2006 Ford F150. This will be a front mounted hitch. Our hitch will install on the inside of the frame. It will use existing holes that are in here. The holes that will be used in the frame will be the square hole here and this round hole up here, that is sometimes covered by this balance right here. We can start by actually holding up the hitch into position. This is a good one to have an extra set of hands for. It goes on the inside of the frame and there are 2 notches on there to keep it a little bit higher or a little bit lower depending on clearance with your bumper. It is a good idea to install your hitch as close as possible then install your hardware. In this case we have the hitch install in the lowest position. That should give you an idea of what kind of clearance you can expect. Once you have your bolts installed you can go ahead and install your hardware. You still want to leave it loose because you might have to move your hitch back and forth for the rest of the hardware.more
Watch Video7/22/2008 7:33:29 PM
