Wiring Harness Installation - 2007 Kia Rondo
Search By Other Makes
Acura(2)
Buick(2)
Chevrolet(21)
Chrysler(7)
Dodge(15)
Ford(14)
GMC(5)
Honda(10)
Hyundai(5)
Isuzu(1)
Jeep(12)
Kia(8)
Lexus(1)
Mazda(1)
Mitsubishi(2)
Nissan(8)
Oldsmobile(1)
Pontiac(3)
Saturn(3)
Subaru(3)
Suzuki(1)
Toyota(10)
Volkswagen(2)
Volvo(2)
Wiring Help
Dielectric Grease ReviewTrailer Wiring Diagrams
5 Wire vs 4 Wire System DemonstrationCircuit Testing for Vehicle WiringTesting for a Correct Ground Connection DemonstrationT-One Wiring Harness ExplanationTrailer Wiring Harnesses TroubleshootingTesting and Troubleshooting a Modulite Vehicle Wiring HarnessInformation Categories
Towing
Ball Mounts (12)
Brake Controllers (55)
Fifth Wheel Hitches (11)
Gooseneck Hitches (11)
Hitch Accessories (15)
Tow Bars (7)
Trailer Hitches (302)
Wiring Installations (152)
Cargo
Bike Racks (94)
Cargo Carriers (46)
Cargo Control (40)
Ladder Racks (20)
Trailers
Trailer Parts (22)
Accessories
Air Deflector (3)
Backup Cameras (7)
Bug Shield (4)
The Essentials (3)
Exhaust System (2)
Locks (64)
Tire Chains (4)
Tonneau Covers (9)
Tools (8)
Towing Mirrors (10)
Tube Covers (13)
Tube Step - Nerf Bar (12)
Vehicle Trim (4)
Vehicle Accessories (13)
This Product Fits The Following Vehicles
2007 - 2010 Kia Rondo
2010 - 2010 Kia Soul
Products Featured in this Video
Manufacturer Instructions
Installation of a Wiring Harness on a 2007 Kia Rondo
Today we are going to do an install with part number 118431 from Tow Ready. We are going to install this T-One Connector on a 2007 Kia Rondo. Our first couple steps are to open up the trunk and we need to remove both tail lights. This is the point right here where the T1 will make the connection. Now we will just take it apart so we can take the light off. We are going to go ahead and do this for the other side also. We will go ahead and make our connection point on the driver side then we will push the rest of this down through the opening and come out down towards the bottom. We will go ahead next and install our ground wire here. At this point we can actually reconnect our light on the drivers side.
From here we can run our red and green wire over to our passenger side. We will run it behind the bumper here and zip tie it to the hitch. Then we can pull it back out on the other side. You will also want to zip tie the module around this bar right here. Now we run the 4 pole over to the middle of the hitch also. The area around the exhaust we are going to take up the slack up and behind the tail light. Not like a bow string or anything just so we can have the wires away from the exhaust a few inches. Next we will go ahead and reconnect our T Connector here. We will take this and pull up our slack and put our light back on over on this side. Here is where we install the bracket which is part number 18144 we are going to just attach it to the bottom of the bumper here. It is pretty sturdy so we will just go ahead and attach it to the plastic here. It will be nice and neat and it will not keep them down any lower then the hitch. It has a friction bit so you can just push it right through. We will take the excess and zip tie it to the hitch to keep it up and out of the way. That completes our install of part number 118431 from Tow Ready on a 2007 Kia Rondo.
