customer service | view cart 
Wiring Harness Installation - 2007 Dodge Charger
Custom Fit Vehicle Wiring
This Product Fits The Following Vehicles
2008 - 2010 Dodge Challenger All Models
2006 - 2010 Dodge Charger All Models
2005 - 2007 Chrysler 300 All, Except 300C, Touring and Limited
Products Featured in this Video
Manufacturer InstructionsInstallation of a Custom T-One Wiring Harness on a 2007 Dodge Charger
Along with your custom receiver hitch for the Dodge Charger you will also need a wiring connector when pulling a trailer. We offer a custom wiring harness that requires no cutting or splicing and will provide a flat four pole connector. This will power the trailers running lights, brake lights and turn signals allowing you to safely and legally tow your toys, boat and trailer. You may also want this to power lights on a cargo trailer or to use a light up receiver hitch cover.
Today we are going to show you part number 118404 which is the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector. It will be installed on a 2007 Dodge Charger RT. To begin our install what we have to do is obviously get into the trunk area. I am going take off these wing nuts, one on each side. Pull back the cover until we can get to our wiring covers. The T-One connector will actually plug in between the light back here and the bar harness here. What we need to do is push in this red tab here then we slide our connector apart. Now we will go ahead and slip on our new connector, it fits just like the old one. For our ground we will attach it to this inside body part here. Then worry about the screw pointing out as opposed to the steel right here hitting the light. So we will go ahead and run our screw in this nice open spot here. Next we will take our green wire and slide it behind the panel here onto the other side. Then basically we are going to repeat what we did on the passenger side on side. Now we will start taking this side apart.
Obviously this harness has a lot of leftover length. We will go ahead and tape this up. We will go about 3 or 4 feet up. The rest will be bundled tight and we will hide it behind the body panel. You can use a zip tie to hold the wires together, basically we are going to hide it behind our paneling back here. Then with the rest of our wire we have a couple of options. One, if we have carpet here you can actually hide it underneath the carpet. Or you can bundle it up and hide it behind the paneling until you need it. Then we will put our inner panel and wing nuts back together. Once the harness is installed we will show you how to use it. It is pretty easy we actually have it tucked in a pocket on the driver side. You can just pull it out and shut your trunk on it and it will not hurt a thing. See you can still pull it out as you need it. It comes out by your the trailer hitch. There you have it for the -One Vehicle Wiring Harness with 4 Pole Trailer Connector part number 118404. Installed on a 2007 Dodge Charger RT.
Filter Videos
- Search By Other Makes
- Acura (2)
- Buick (2)
- Chevrolet (21)
- Chrysler (7)
- Dodge (16)
- Ford (14)
- GMC (5)
- Honda (10)
- Hyundai (5)
- Isuzu (1)
- Jeep (12)
- Kia (8)
- Lexus (1)
- Mazda (1)
- Mitsubishi (2)
- Nissan (8)
- Oldsmobile (1)
- Pontiac (3)
- Saturn (3)
- Subaru (3)
- Suzuki (1)
- Toyota (10)
- Volkswagen (2)
- Volvo (2)
- Wiring Help
Dielectric Grease Review- Trailer Wiring Diagrams
5 Wire vs 4 Wire System Demonstration- Circuit Testing for Vehicle Wiring
- Testing for a Correct Ground Connection Demonstration
- T-One Wiring Harness Explanation
- Trailer Wiring Harnesses Troubleshooting
- Testing and Troubleshooting a Modulite Vehicle Wiring Harness
Search
Contact and Help
What our customers said:
I just wanted to thank you for the excellent service and outstanding product. I certainly will keep your web-site at hand if I need other parts. Thanks again Dick
Dick
Deer Park, WA
