All you have to do is get to the inside panel and get to the connector. Basically we have to take out this panel, and this panel to get the spare tire well and we can find our panel that way. Once you get to the spare tire well you should see this connector wrapped in blue tape. Your T-connector will plug right in to that and well go ahead and make a permanent mounting. We can route this back here and make sure you have enough wire coming out. After that go ahead and stick it down with the adhesive.
When you dont need it, it can sit with the spare tire, when it is needed go ahead and pull it out. When you shut your hatch on it this door seal will give plenty of room for the wire to do its thing even if it needs to go in and out. Its still nice and loose and it wont get pinched when its hanging out the door.
Trailer Wiring Harness Installation - 2003 Subaru Forester - Hopkins
Today on our 2003 Subaru Forester we're going to install the Hopkins 4-Pole Wiring Kit, part number 33855. First we'll need to access the rear cargo area. Then we're going to open up the access to the spare tire. Alright, next on the passenger's side we're going to go ahead and remove the spare tire tools and there's a fastener here to remove this panel. This exposes us to the rear trailer connector that we're looking for. So this application is being wrapped in blue tape.
Trailer Wiring Harness Installation - 2003 Subaru Forester - Tow Ready
Today on our 2003 Subaru Forester we're going to install the Tow Ready T1 Connector, part number 118461. First we'll need to access the rear cargo area. Then we're gonna open up the access to the spare tire. Alright, next on the passenger's side we're gonna go ahead and remove the spare tire tools and there's a fastener here to remove this panel. This exposes us to the rear trailer connector that we're looking for. So this application is been wrapped in blue tape.
Trailer Wiring Harness Installation - 2011 Subaru Forester
Today working on a 2011 Subaru Forester, were going to install a Tow-Ready T-One Connector part# 118467. Go ahead and remove the cargo cover, were going to remove the center foam tray and the driver's side foam tray to access the wiring underneath. And you see it gives us access to the manufacturer's trailer wiring. Now we can take our new Tow-Ready Connector and plug it into the manufacturers connection port. With our port connected we need to mount our converter box, we'll peel back the cover of the two-side adhesive and mount it to the sheet metal. Were mounting it to the sheet metal make sure you've got a good flat clean surface.
Trailer Wiring Harness Installation - 2009 Subaru Forester
Today on this 2009 Subaru Forester we are going to be installing wiring harness part number 118467. We are at the rear of the vehicle and the port that we are going to need to plug our wiring harness into is located inside the cargo area underneath the floor board over here on the driver side of the vehicle. We are going to need to remove quite a few pieces to gain access to the port. The driver side styrofoam has a few retaining fasteners holding it in to position. To remove those you can either use a flat headed screwdriver or you could use a rivet removal tool. 00:33
Trailer Wiring Harness Installation - 2010 Subaru Forester
Today on this 2010 Subaru Forester we are going to be installing wiring harness part number 118467. We are in the rear cargo area of the Forester and we want to locate the port that we are going to be plugging our wiring harness into. This port is located underneath the cargo floor over on the driver side of the vehicle. We are going to need to remove a few pieces before we can get started. We obviously need to remove the covering not only in the center section but on the driver side as well. Then we need to remove the styrofoam storage bin on both the center and driver side sections as well. For the driver side compartment there is actually two push pins that are holding it into position. 00:29
Trailer Wiring Harness Installation - 2009 Subaru Forester
Okay, today on our 2009 Subaru Forester we are going to install part number 118467 from Tow Ready. Okay, the first thing we need to do when we install our wire harness is get down to the spare tire area, so we are going to take off this mat here get it out of our way. Take out the foam s. We will take this out of our way, and we will remove the net. Okay, and then this foam section here also has to come out. :31
