Today on this 2009 Dodge Ram 3500 Series we will be installing the fifth wheel and goose neck wiring harness part number V30137. The first thing I want to note before we get started is that our harness comes in two separate pieces. We have got the 7-pole which is what we are going to be mounting in to the bed of the truck and then we have got the wiring harness itself. The wiring harness has two different ends on it. The one end of the wiring harness has a larger round plug and that is what is going to plug directly into the back of our 7-pole. The other end which we are going to feed down through the opening in between the bed and the fender well has the two square ports. The first thing I am going to do is drill out the hole in the bed for the 7-pole. We are going to be using a two inch hole saw to accomplish this. Next we are going to feed the square ports through the hole that we just drilled down underneath the vehicle. Then we want to plug in the round port into the back of the 7-pole and we just want to make sure we hear the snap so that we know that the two ends are engaged. 01:00
The harness kit provides some 1/ 8 inch self tapping screws to mount the plug with. I am going to use hex headed self tapping screws. Next we will go underneath the vehicle and we want to disconnect the plug in the back side of our 7-pole. If the plug in to the back side of the 7-pole is the square port you will need to use part number V30137. If the plug end on the back side of your 7-pole is the round port you will want to use part number V30133. There is a red tab which is hard to see on the top of the connector that we need to release first so I am just going to take a flat headed screwdriver and push that over. We are pushing that towards the driver side of the vehicle and then there is a little tab on top as well that we need to press in and then we can just pull back. We next want to take our wiring harness and route it over the frame. We want to make sure that we avoid any possible pinch points. The only thing left to do is tie up the excess wires that we have in our wiring harness. The wiring harness kit provides cable ties to do this. That will conclude the installation of the fifth wheel and goose neck wiring harness part number V30137 on a 2009 Dodge Ram 3500 Series.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2005 Dodge Ram
Today on our 2005 Dodge Ram Pickup, well be installing the Bargman 5th Wheel Gooseneck 90 Degree Wiring Harness with 7-Pole plug, part number 51-97-411. To begin our install, well first locate in the pickup bed where well be mounting our 7-pole, then using a smaller bit for our pilot hole, once weve located a spot well go ahead and drill our hole. Well go ahead and drill out using the two inch hole saw as recommended per the instructions. Now with the large hole drilled out, well go ahead and feed half of our T-connector through the hole then our other plug followed by the remainder of the wire until our 7-pole mounts flush with the bed. Then using the self-tapping screws provided with our install kit, we can go ahead and secure the 7-pole plug to the bed side. Next well get underneath the vehicle and start routing our wire over to the back of the bumper where the manufacturers wiring meets the bumper. Here at the back of the bumper, well go ahead and disconnect the manufacturers wiring from the back of the 7-pole plug at the bumper.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2012 Dodge Ram Dully
Today on our 2012 Dodge Ram 3500 dual rear wheel, we'll be installing the Pollak fifth wheel goose neck T-connector with seven pull, part number PK11893-11932. First, we'll go ahead and locate a suitable location for our new seven pull connector. Here, just behind the rear wheel on the driver's side is a common position. Go ahead and locate the area, check underneath to make sure there are no obstructions, and then we'll go ahead and use a small pilot hole and drill it out. This will allow us to again get underneath and double check where the pilot hole location is and correspond it's where our seven pull connector will be. With that done, we can now go ahead and take the hole saw and cut out the larger hole to fit the seven pull connector.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2012 Dodge Ram
Today on our 2012 Dodge Ram 2500, we are going to be installing the Pollock fifth wheel and gooseneck T-Connector with seven-pole wiring part number PK11893-11932. First, we need to begin by finding a suitable location for our seven-pole in the bed. Just here past the cut out in the bed behind the drivers side wheel well is where we are going to mount our sub pole connector. First step will be drilling a pilot hole. Ill take my eight-inch bit which will be the same as the pilot hole for hole saw that we will need to cut out. Now I can go underneath and check to make sure its not going to run into anything.
Trailer Wiring Harness Installation - 2011 Dodge Ram
Today on our 2011 Dodge Ram well be installing the Pollak fifth wheel and goose neck connector wiring harness part #: PK11932. First well need to locate a suitable spot for installing the connector in the truck bed. Then Ill take a pilot bit and run it through the bed and double check my location. Were going to go ahead and take a quarter inch bit which will be the same size as my pilot bit for my hole saw and drill out the hole. Now with my hole drilled out well go ahead and take the hole saw and make it large enough for the connector to fit through. With the large hole drilled out we can now take the wiring harness and feed it from underneath through the hole.
Trailer Wiring Harness Installation - 2001 Dodge Ram
Today on this 2001 Dodge Ram pickup 1500 were gonna install part number 118329 from Tow Ready. This is a 4-pole wiring harness. Alright well go ahead and show you where the connection points are if were looking at the driver side of the vehicle it will be right behind the bumper and this is our first connection point right here. inaudible you got to push in that way and you can pull it apart. inaudible the 2 pieces well install the T-connector with the yellow wire, then well route this wire and the 4-pole wire over to the center of the hitch. Well do that by following the factory wire harness inaudible with the green wire and were now on over to the other side.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2004 Dodge Ram 3500
Today on this 2004 Dodge 3500, we are going to install the pre-wired fifth wheel trailer connect that mounts in the pickup bed, part number 51-97-411. Start by looking for a spot to install our assembly connector. We are going to mount ours here, just behind the wheel well in the pickup bed. Using a 1/4 inch bit we will make a pilot hole so that we can use our hole saw bit to drill out a 2 inch hole so that we can mount our connector. Now you can leave your drill bit in the hole, go underneath and check to make sure you have enough clearance to fit your 7 way wiring through. Now we will go ahead and drill it out with our 2 inch hole saw bit.
