Today on this 2004 Jeep Wrangler we will be installing wiring harness part number 118409. We are underneath the Wrangler here, we are actually directly under the tail-light assembly underneath the car. The ports that we are going to be looking for to plug our harness into are located up above this rubber covering here. So we need to pull this back to gain access to the port. You can see we have one push pin here that is holding it into place, so we need to release that first.
Here is the port we are going to be plugging our harness into. We need to separate those two pieces and to do so, you can kind of see here from the backside there is a tab there at the top. We just need to press that in and separate the two pieces. We will next take our harness and go ahead and plug it into place. Over here on the drivers side we are going to be connecting the ports that have the yellow and brown wires in it. And I am just going to pull that in line with the connectors that we just separated.
Okay then we are going to take the other connector with the green and white wires, we are going to mount it over the frame rail here. Do this as well with the 4-pull end. Feed it over to the middle area where the 4-pull is going to be tied off here at the trailer hitch. And then we will continue the other connector over and plug it into the passenger side. You can see on the passenger side that the connector is not not easily visible. What we are going to do is take and just trace the loom that is feeding up to the tail light. It is kind of in between the body and the bumper here. Pull that access portion of it out, and you can see we have located our connector there and it is covered in protective tape. You want to go ahead and pull the tape off of there, and again just take and push the release pin, or button here, separate the two connectors, and plug our harness in line.
Then next we are going to take our ground wire here and we are actually going to go ahead and mount it directly to the frame using a self tapping screw that is provided with our installation kit. Hook our connector back up behind the bumper here. Then we will reinstall our protective cover. Than we can go back over the the drivers side and pull the excess wire back up into the compartment here. And here are the zip-ties that are proved with the installation kit. And we can go ahead and replace the cover on the drivers side as well. Okay then I am going to come back to the front here where the 4-pull is and again if you have any extra loose wires just kind of hanging low you can take the remaining zip-ties and you can zip-tie the wires to some of the holes in the bumper. And this will conclude the installation of wiring harness part number 118409 on a 2004 Jeep Wrangler.
Trailer Wiring Harness Installation - 2011 Jeep Wrangler
Today on this 2011 Jeep Wrangler were going to install part number 118416 from Tow Ready. This is our T1 wiring harness. The first thing we need to do is go ahead and remove the taillight on the drivers side. There are two screws we have to remove and then the light can be detached from the vehicle. Next well disconnect the wire harness from the light. Theres a small tab we have to push down and then you can pull it apart.
Trailer Wiring Harness Installation - 2005 Jeep Wrangler
Today on our 2005 Jeep Wrangler, we're going to install Part # 118409 from Tow Ready. The first thing we have to do is look underneath the vehicle, we're looking at the driver side and we need to remove this panel underneath here. A little plastic with it, we can remove like move the panel out of the way. Our connection point will be wrap up and tape right here. Pull this and remove the tape and disconnect it. When there's a tab, you have to push down so you can pull the part.
Trailer Wiring Harness Installation - 2012 Jeep Wrangler
Alright, today on this 2012 Jeep Wrangler were going to install part number 118416 from Tow Ready. First thing we need to do is go ahead and remove the tail light. And then we'll go ahead disconnect our tail light right here, push down on this tab and it should come right apart. Alright, now we'll take our T1 harness, we're going to take the 4-pole and rout it inside the body for now. And then we'll test the matching in of our T1 connector to the factory wire harness and snap it together. Alright now were going to take our white wire with the ring terminal, peel this back a little bit and run it down outside to the frame for our ground point.
Trailer Wiring Harness Installation - 2000 Jeep Wrangler
Today in this 2000 Jeep Wrangler we are going to install a Tow Ready T1 Connector, product number 118409. We'll also be using Tow Ready 4-Flat Connector Mounting Bracket, product number 118144. First, we need to access the vehicle's manufacturer wiring. To do that we're going to remove a push pin underneath the tail light wiring that will give us access to the manufacturer's wiring. We'll go ahead and repeat the same process in the passenger side. As you can see, we now have access to the manufacturer's wire and we'll follow the lead that goes to the back of the tail light.
Trailer Wiring Harness Installation - 2006 Jeep Wrangler
Today on this 2006 Jeep Wrangler, we will be installing wiring harness part number 118409. We are going to start off underneath the vehicle. We are on the driver side, directly below the rear tail light. The parts we are going to be plugging our wiring harness into are located in this pocket underneath the vehicle. We are going to remove this down and show you where the connector is. Holding this flap up is a push rivet. You want to remove that. With that removed we can pull the flap down. If you look up in here, covered in protective tape is our connecting port that we will be plugging our wiring harness into. :40
Trailer Wiring Harness Installation - 1999 Jeep Wrangler
Today on this 1999 Jeep Wrangler we are going to install part number 118409 from Tow Ready. This is their T-One wire harness. Right now we are looking at the driver side of the vehicle and our connection points are going to be behind the body work right here so pull away the plastic trim panel right here to get access to the wiring. There is a little plastic rivet right here that we have to remove. Now you have to follow the wire harness up and there will be a connection point where you unplug. This one happened to have a bunch of tape wrapped around it so uncover the tape to get to the connection harness. It is kind of hard to see but there is a little latch on the top. Push down on it and it should pop apart. 00:39
