Select Your Vehicle
CartView Cart

Free Shipping on Orders Over $99

Only 20 Hours 20 Minutes Remaining



Trailer Wiring Harness Installation - 2004 Honda Odyssey

content loading



Honda Odyssey Wiring



Products Featured in this Video


Installation of a Wiring Harness for a Trailer on a 2004 Honda Odyssey


Today we are going to install part number 118336 from Tow Ready, and we are going to do this on our 2004 Honda Odyssey. The port where we need to get to the wiring is inside the vehicle, so we need to open up the hatch and get to the inside, drivers side quarter-panel. To get behind our quarter-panel here, we have to get behind this access panel. Pull this loose, so you can undo this one, and then get back behind the wiring harness which is located in this general area, here. And there are a couple of clips back in here, and if you kind of put your fingers in there to work it out, it will come loose. Just keep working it back and forth until you get the brake loose until you get enough to where you can get your hand in there.

Also, if you need more room to get in there, you can actually take out the jack tools there is a little screw right here. Undo that, and that gives you a little more play to pull off the plastic to give yourself a little more more room. If you want to get access to the wire harness, look for this plug right here with the blue tape. That is the tow package port, right there. You simply just take it away from the tape and simply plug in the harness into the port. All right, next you want to take your converter box and just attach it to some of the steel inside of here , or maybe put it behind the sheet metal here, too. At this point, we go ahead and start reassembling our interior panels. When you put your panel back together, make sure that your wire harness comes out toward the bottom, here. And what happens is, when you use it, you pull it out to the hitch on your vehicle.

To use the harness, just pull it out and you can shut your trunk on it, because the door seal here is thick enough where it will not hurt the wire. Just make sure you stay away from the latch, and you pull out as much as you need. And when you are not using it, you simply store the wire harness inside the vehicle. All right, and that covers our install of part number 118336 from Tow Ready on a 2004 Honda Odyssey.



Info for this part was:


Video Edited:
Zack K

Video Edited:
Andrew K

Video Edited:
Joshua S

Test Fit:
Nicholas E

Video Edited:
Andrew L

Installed by:
Cole B

Test Fit:
Shane T

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.

Ask your question or add a comment to this video?

Name: (example: John S.)



Contact email:



Comment or Question



Yes, I would like an email notification if someone replies to my comment?   






Honda Odyssey Custom Fit Vehicle Wiring Videos

Trailer Wiring Harness Installation - 2008 Honda Odyssey

Today on our 2008 Honda Odyssey we'll be installing the Tow Ready T1 Vehicle Wiring Harness with 4-pole flat connector, part number 118438. To begin our install, we'll first open up the rear cargo door. Then we'll need to remove the rear threshold. To remove the rear threshold there are two tow hook fasteners that have to be screwed out first. Once we remove these fasteners we'll then use a flat bladed screwdriver or an interior trim panel tool to get underneath the threshold and pop the fasteners free. At the top and bottom of the threshold we'll go ahead and turn it over and see the fasteners that are underneath. Next on the driver's side we're going to go ahead and remove the spare tire cover and jack storage compartment door.



Trailer Wiring Harness Installation - 2014 Honda Odyssey

Today in our 2014 Honda Odyssey we'll be installing Tow-ready T1 vehicle wiring harness, part number 118521. To begin our install we'll first need to go ahead and open up the rear cargo door. Then we'll remove the rear threshold. To remove the rear threshold, we'll first need to remove the two tie-down fasteners, one located on each side. Then, using an interior trim panel tool or a flat-blade screw driver, we'll get underneath the threshold and release the fasteners underneath, as we pull out and up on the rear threshold. Now once we've released the fasteners underneath, we can go ahead and remove the threshold and set it aside for reinstallation later.



Trailer Wiring Harness Installation - 2012 Honda Odyssey

All right, today on this 2012 Honda Odyssey, we're going to install part number 118521 from Tow Ready. First thing we need to do is get inside the hatch of the vehicle and we'll go ahead and remove the threshold plate. The cargo has hooks we have to remove. We'll put a piece of a towel over them and use some pliers to unscrew them, and then we'll go ahead and use a trim panel tool to pop up the plastic rivets underneath and pop up the panel. Well go over the driver's side panel and remove the cargo hook there too. Okay, and then we'll pop the panel loose as well.



Trailer Wiring Harness Installation - 2009 Honda Odyssey

Today on our 2009 Honda Odyssey, well be installing the Tow Ready T-1 connector part number 118438. To begin our installation, well first remove the jack storage door. Next, were going to remove the rear threshold. To remove it, well first remove the two tie-down hooks. Next, well go ahead and get our hand underneath the bottom of the threshold and pop the plastic passenger strip from the sheet metal. Then we can take the flat-bladed screwdriver or in this case a trim panel tool and get up underneath the threshold and pop it free.



Trailer Wiring Harness Installation - 2007 Honda Odyssey

Today in our 2007 Honda Odyssey will be installing a toe ready T1 connector part no. 118438. First we open up the rear cargo door then were going to remove the rear trunk panel and trash hold to remove the rear trash hold you first need to remove the two cargo hooks now we go and pop trash hold free now with the trim panel and trash hold set aside were going to move over to the passenger side and remove the rear trim quarter panel. When removing this panels you can use a flat plated screw driver or a trim panel tool as we are in this case now with the panel free you can see the black electrical box. The top rack corner of the electrical box will match identically to the great connector of our new toe ready T1 harness. Well plug directly in to it and lock in place next we need to take the white wire the ring terminal pre form and attach it to a ground here next to a electrical panel is a manufacturers ground that we can use first of all we remove the ground stud, install the ring terminal and then reinstall our ground stud.



Trailer Wiring Harness Installation - 2011 Honda Odyssey

Today on this 2011 Honda Odyssey were going to install part number 118521 from Tow Ready. The first thing you need to get inside the vehicle. All right. Now you have to take the seats and get them out of our way. I like to remove the threshold right here. We remove this fastener here and theres one on the other side.



see all 325 Honda Odyssey videos       








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email





Free Shipping on Orders Over $99

Only 20 Hours 20 Minutes Remaining


etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com