All right, today on this 2012 Honda CR-V, we're going to do a test fit of part number Y02098 from Yakima. This is the forklift roof mounted bike carrier. Now our Honda's already been equipped with a Yakima roof rack system and a bicycle rack who's already been assembled according to the instructions so all I got to do is place it on the roof rack. We'll start off by placing the front half of the bicycle rack with your front bar and then we'll go ahead and put the clamp onto it and route it underneath the bar and then loosely secure it. Then we'll go ahead and do the same process for the clamp at the back bar. All right, now we'll go ahead and take a second to make sure the roof rack is in the spot we wanted and make sure it's even in a straight line going front to rear.
All right Once we have the bike rack in its final position, we'll go ahead and tighten it down. We'll make sure every tabs on the handle are pointing front to rear from the front clamp and then we'll go ahead and slide the cover on over the handle. Then we can go ahead and install the skewer. We'll make sure the skewer is operating correctly, then when can go ahead and load up the bike. Make sure the skewer is in the open position and the strap for the back wheel is out of the way.
Okay And we'll load up the bike, we'll put the fork into the skewer, and then make sure the back wheel is on the track in the back and the strap goes through it. Then we'll go ahead and tighten down the skewer on the fork and then secure the strap in the back. Okay, and that's what it takes to load up the bike. And with that, that'll finish it for our test fit of part number Y02098 from Yakima. The forklift roof mounted bike carrier on our 2012 Honda CR-V..
Today on our 2013 Honda CR-V, we're going to be test fitting the RockyMounts TieRod Roof Mounted Bike Carrier, part number RKY1014. Our CR-V is already equipped with a factory roof rack so we're going to mount the RockyMounts TieRod directly to the factory cross bars. We'll lift up the carrier and set it on top of our cross bars. We'll feed the straps at the head of the bike carrier around our front bar. Lock them back into the head and use an Allen key to tighten them down. Then we can reinstall the cover on the head of the bike rack.
Today on our 2013 Honda CRV, we're going to be test fitting the Thule Domestique roof-mounted bike carrier, part number TH513. To mount the carrier to our roof rack, we'll set it up on top of our cross bars, and then we can fit the head of the bike rack over our front load bar. We'll lift the bottom clamp around the bottom of our load bar, and use the included Allen key to tighten down the Allen head bolts. Once we have the head of our bike rack secured, we can move to the rear. We want to position the rear clamp and again tighten it down with the included Allen wrench. Once we've done that, we'll take our skewer and reinsert it into the head.
Today on our 2012 Honda CRV well be test fitting the Swagman roof mounted bike carrier part #: S64710. To mount the bike carrier onto our roof rack well set it in place on top of our load bars. Well fit the U-bolt clamps around our crossbars and then tighten them down using the included wing nuts. Well feed the clamping bar around our rear crossbar and again tighten it down with our wing nuts. With that done were ready to load our bike. Well drop our front fork into position on the skewer, well secure the bike by the front first and then well move back to the rear and tighten it down with the wheel strap.
Today on our 2012 Honda CRV well be test fitting the Rocky Mounts Tie Rod roof mounted bike carrier part #: RKY1014. To mount our bike carrier up on top of our roof rack well set it up on top of our crossbars first. Well fit the rubber coated steel straps on the front head around our front crossbar. Well fit them back into the head and tighten them down using the included Alan key. In the rear well fit the clamp over our rear crossbar and use the wing nuts to tighten it down. With that done our bike racks installed on our roof rack and were ready to load our bike.
All right, today on this 2012 Honda CR-V, we're going to do a test fit of part number Y02103 from Yakima. The front loader wheel mount bike carrier. Our Honda's already been equipped with a Yakima roof rack system. Okay, we'll start off with our roof rack already been assembled according to the instructions. So we'll start off by putting the front half onto the front crossbar and attaching it loosely. And then we'll go ahead and make sure if our clamp for our rear crossbar is slid in position and then loosely clamped down as well.