Today on this 2001 Ford F-150 super crew, we are going to install part number TX590601 from TruXedo. This is their QT tonneau cover. The first thing we want to do is go ahead and lay out our parts and we are going to work with our side rails first. If you notice, on the rails here they have these slots right here and the edges are kind of sharp. So, the kit comes with these simple little covers that you just snap over the edges. Then go ahead and go on to the rest of the slots and cover those up. We can go ahead and start installing the first rail. 032
We are going to start off on the passenger side. And you can see right here, there is a catch that goes towards the back of the vehicle. And on the other side, there is an adjustment bolt and that tells you that goes to the front. We are going to hold it up against the edge of the bed rail itself and we are just going to temporarily clamp it in place. And on the front, you want to position the rail where it is about 1/8 of an inch above the cap. Now, if you do not have a good way to clamp it in position, you are just going to have to use the clamps that come with the kit. Now you will notice that the clamp is offset because the rail is going to sit higher in this part here. So the rail is going to sit higher but this part actually bottom outs on the inside edge of the rail. You can still adjust it with these slots right here. Get the rail where you want it and push out the back side as far as you can go and then tighten it down. Our next clamp is going to go on the other side of the pocket right here. And it is going to be like that on all four corners since there is nothing really to clamp to in the middle of the bed. When you tighten this down, you want the rail to sit level. If it is up or down a little bit, then you may have to readjust the clamp. Alright, now we are going towards the back of the rail, towards the tailgate. And let us repeat the same process. Now let us go ahead and repeat the same process back over on the driver side. 1:50
Alright, now we will go ahead and start working on the tonneau cover itself. This is the latch right here and right now it is open so we can install it. When we have it installed, we will push this latch shut. It locks into place and it cannot come back because there is a catch right here. And to open it up, just push it down and pull it back. So we will just go ahead and flip it over. Take one end and fit it in and then check on the other side. And then we will just take our latch and lock it in. Alright, let us go ahead and unroll it. Make sure these cross bars fit in the slot as well. Make sure this part will catch right here. Do it on both sides and then just push down on it. And then take it and pull it out. Make sure the Velcro attaches. And when you want to unlatch it, pull this lever right here and just roll it back up. And we need to use the truck bed itself. These straps will wrap around and they will hook into this loop right here. And with that that will finish it for part number TX590601 from TruXedo.
Bestop EZ Fold Folding Tonneau Cover Installation - 2006 Ford F-150
Today on our 2006 Ford F150 well be installing the Best Top EZ Folding Tonneau cover, part number B1611101. First before we install the tonneau cover well go ahead and remove the protective cover from the weather strip. Simply peel it back and remove it, setting it aside. Now well go ahead and take the tonneau cover, put it up on the bed rails nearest the cab, lining the front edge up with the bulk head of the truck bed. Now well go ahead and adjust it, make it even from side to side. Now with the tonneau cover in position well go ahead and get underneath the tonneau cover, lower the clamp, slide it into place.
Access Roll-Up Tonneau Cover Installation - 2010 Ford F-150
Today on our 2010 Ford F150 well be installing the Access Rollup Tonneau Cover, Limited edition, part number834532004720. Stop fighting your bed cover. This one takes only seconds to open and close, no matter what the weather. After opening the packaging and making sure that we have all the pieces well begin by installing the rails onto the bed side. When placing the rail onto the bed side, well want to make sure that the two ends are level with the truck bed lift. Now for the time being, well use a clamp to hold the rail in place.
Access Toolbox Edition Tonneau Cover Installation - 2012 Ford F-150
Today, on this 2012 Ford F-150, we will be installing the Access roll-up Tonneau cover, part number 834532004782. Our first step will be to install the weather seal at the bulkhead, which is the front wall of the truck bed. We will take our alcohol prep pad, clean the surface, then peel back the 2-way adhesive and adhere the seal to the bulkhead. Then, we are going to go ahead and put our truck box in place, tighten it down so that we can install the front header bar of our Tonneau cover. We will push this up against the truck box with the weather seal facing the box and adhere the side rails with the clamps provided. Now, with our header bar in place, we can go ahead and start attaching the side rail.
Bestop EZ Fold Tonneau Cover Installation - 2010 Ford F-150
Today on this 2010 Ford F-150 we are going to install the EZ Fold Tonneau Cover from Bestop. We are going to be using part number B1611101. Installing this Tonneau cover is relatively easy. It is very light to install but it is always a good idea to have an extra set of hands. All you have to do is start with the Tonneau cover and just fold it up into position and set it on the rails closest to the cab of the truck. Take it and line it with the front edge of the bed itself. You will notice the clamps are built on to the Tonneau cover itself and it is adjustable left and right to accommodate different bed widths and basically what you do is slide it over and adjust the clamp up and down as needed so you can start off with the clamp as close to the rail as possible. 00:40
Access LiteRider Tonneau Cover Installation - 2010 Ford F-150
Today on this 2010 Ford F-150, we are going to install part number 834532004737, the Access tonneau cover LiteRider. The first thing that we need to do is install the side rails that go into the bed of the truck. Alright, we are going to take our first rail. We are working with the driver side. We are just going to hold it up to the inside edge of the top rail of the truck and we will make sure that this edge is flush with this or maybe a little bit higher will work just fine. You will notice on the rail here that we have this plastic edge here. That is where the back part of the tonneau cover locks into place. You want to have this towards the back of the truck when you install the rails. Scoot it all the way towards the front and make sure that touches the front rail. Once we have it the way we want, we are just going to use a clamp just to hold it in place. We will start working on the clamps that will hold it permanently in place. Take your clamp, push it into place. I like to go as far as I can on the inside edge of the rail and try to go as far back as possible. 1:03
