Today in our 2007 Honda Odyssey will be installing a toe ready T1 connector part no. 118438. First we open up the rear cargo door then were going to remove the rear trunk panel and trash hold to remove the rear trash hold you first need to remove the two cargo hooks now we go and pop trash hold free now with the trim panel and trash hold set aside were going to move over to the passenger side and remove the rear trim quarter panel. When removing this panels you can use a flat plated screw driver or a trim panel tool as we are in this case now with the panel free you can see the black electrical box. The top rack corner of the electrical box will match identically to the great connector of our new toe ready T1 harness. Well plug directly in to it and lock in place next we need to take the white wire the ring terminal pre form and attach it to a ground here next to a electrical panel is a manufacturers ground that we can use first of all we remove the ground stud, install the ring terminal and then reinstall our ground stud.
Now we are ready to go ahead and mount the converter box over a new harness. Well remove the two sided tape and attach to a clean flat surface once we completed that well route the four pole harness back over to the driver side and fitted in behind the jack storage area and then we can go ahead reinstall all the trunk panels as we route our four pole connector over to the driver side behind the jack storage compartment well secure the wire to the manufacturers harness using the black zip ties provided. Once weve got our wire secured well go back and just take a pair of side cutters cut off the excess from the zip ties. Now were ready to go ahead and reinstall the interior trunk panels. When everything is reinstalled lets go ahead and show you how to use your new four pole connector.
Is it comes out to the jack storage compartment we route over to the center of the vehicle and down to the hitch or accessory. Be mindful to stay away from the latch as pinching in the latch can harm the wire however the wire is thick enough that we can go ahead and close the door on the four pole wire then once were completed using our new four pole connector we can simply roll it up and again store it in a jack storage compartment and then reinstall the jack storage compartment door. Alright now we have the new four pole connector installed weve got one more step on the passenger side in the lower kick panel were going to remove the fuse paneled door. After we remove the fuse panel door well locate the fuse number five which will be an open slot well now insert the 7.5 amp fuse supplied with their installed kit then we can go ahead and take the label and install it on the fuse panel door to indicate that weve now inserted the 7.5 trailer amp fuse. Go ahead and reinstall the fuse panel door and this is to complete the installation of our new toe ready T1 connector part number 118438 on our 2007 Honda Odyssey..
Trailer Wiring Harness Installation - 2012 Honda Odyssey
All right, today on this 2012 Honda Odyssey, we're going to install part number 118521 from Tow Ready. First thing we need to do is get inside the hatch of the vehicle and we'll go ahead and remove the threshold plate. The cargo has hooks we have to remove. We'll put a piece of a towel over them and use some pliers to unscrew them, and then we'll go ahead and use a trim panel tool to pop up the plastic rivets underneath and pop up the panel. Well go over the driver's side panel and remove the cargo hook there too. Okay, and then we'll pop the panel loose as well.
Trailer Wiring Harness Installation - 2009 Honda Odyssey
Today on our 2009 Honda Odyssey, well be installing the Tow Ready T-1 connector part number 118438. To begin our installation, well first remove the jack storage door. Next, were going to remove the rear threshold. To remove it, well first remove the two tie-down hooks. Next, well go ahead and get our hand underneath the bottom of the threshold and pop the plastic passenger strip from the sheet metal. Then we can take the flat-bladed screwdriver or in this case a trim panel tool and get up underneath the threshold and pop it free.
Trailer Wiring Harness Installation - 2011 Honda Odyssey
Today on this 2011 Honda Odyssey were going to install part number 118521 from Tow Ready. The first thing you need to get inside the vehicle. All right. Now you have to take the seats and get them out of our way. I like to remove the threshold right here. We remove this fastener here and theres one on the other side.
Trailer Wiring Harness Installation - 2002 Honda Odyssey
Today we are working on a 2002 Honda Odyssey. We are going to install a Tow Ready T-One Connector part number 118336. First well access the rear cargo area of the vehicle. Then well need to remove one of the cargo hooks. We are going to peel back the tab and remove the screw. With the screw removed we can take a trim tool or flat plated screw driver, get behind the panel and slowly pry it away from the sheet metal behind it.
Trailer Wiring Harness Installation -2003 Honda Odyssey
On this 2003 Honda Odyssey we are going to install part number 118336 from Tow Ready. To install this we have to get inside the vehicle. The port we need to plug into is on the driver side, behind the interior panel right here. We will have to remove the threshold panel here in order to loosen and remove the driver side interior panel. At this tie down point here, we have to remove the cover and this bolt. Then we have to remove these tie down points here and pop open the cap. There is a screw inside to remove. :36
