Today on our 2005 Jeep Wrangler, we're going to install Part # 118409 from Tow Ready. The first thing we have to do is look underneath the vehicle, we're looking at the driver side and we need to remove this panel underneath here. A little plastic with it, we can remove like move the panel out of the way. Our connection point will be wrap up and tape right here. Pull this and remove the tape and disconnect it. When there's a tab, you have to push down so you can pull the part.
We can demonstrate that tab with a new connector with a T1 harness. This is about what we're looking for on the factory connector. We'll take our T-connector with the yellow wire and attach it. Push it until it snaps on both sides. Now, we're going to go ahead and run our purple wire over to the center of the hitch so we'll take our T-connector with the green wire and run it all the way across and go over to the passenger side taillight.
To pull back the white wire with the red terminal for ground just a little bit before it takes a T-connector running up on the taillight. Now this connection will be a lot harder to find. Now, we'll take a ground wire and we'll attach directly to the frame using the self-tapping screw. Now you can go ahead and reinstall our panels and then secure the wires. With all the wires secured, that will finish it for our install Part # 118409 from Tow Ready on our 2005 Jeep Wrangler..
Trailer Wiring Harness Installation - 2011 Jeep Wrangler
Today on this 2011 Jeep Wrangler were going to install part number 118416 from Tow Ready. This is our T1 wiring harness. The first thing we need to do is go ahead and remove the taillight on the drivers side. There are two screws we have to remove and then the light can be detached from the vehicle. Next well disconnect the wire harness from the light. Theres a small tab we have to push down and then you can pull it apart.
Trailer Wiring Harness Installation - 2012 Jeep Wrangler
Alright, today on this 2012 Jeep Wrangler were going to install part number 118416 from Tow Ready. First thing we need to do is go ahead and remove the tail light. And then we'll go ahead disconnect our tail light right here, push down on this tab and it should come right apart. Alright, now we'll take our T1 harness, we're going to take the 4-pole and rout it inside the body for now. And then we'll test the matching in of our T1 connector to the factory wire harness and snap it together. Alright now were going to take our white wire with the ring terminal, peel this back a little bit and run it down outside to the frame for our ground point.
Trailer Wiring Harness Installation - 2000 Jeep Wrangler
Today in this 2000 Jeep Wrangler we are going to install a Tow Ready T1 Connector, product number 118409. We'll also be using Tow Ready 4-Flat Connector Mounting Bracket, product number 118144. First, we need to access the vehicle's manufacturer wiring. To do that we're going to remove a push pin underneath the tail light wiring that will give us access to the manufacturer's wiring. We'll go ahead and repeat the same process in the passenger side. As you can see, we now have access to the manufacturer's wire and we'll follow the lead that goes to the back of the tail light.
Trailer Wiring Harness Installation - 2006 Jeep Wrangler
Today on this 2006 Jeep Wrangler, we will be installing wiring harness part number 118409. We are going to start off underneath the vehicle. We are on the driver side, directly below the rear tail light. The parts we are going to be plugging our wiring harness into are located in this pocket underneath the vehicle. We are going to remove this down and show you where the connector is. Holding this flap up is a push rivet. You want to remove that. With that removed we can pull the flap down. If you look up in here, covered in protective tape is our connecting port that we will be plugging our wiring harness into. :40
Trailer Wiring Harness Installation - 1999 Jeep Wrangler
Today on this 1999 Jeep Wrangler we are going to install part number 118409 from Tow Ready. This is their T-One wire harness. Right now we are looking at the driver side of the vehicle and our connection points are going to be behind the body work right here so pull away the plastic trim panel right here to get access to the wiring. There is a little plastic rivet right here that we have to remove. Now you have to follow the wire harness up and there will be a connection point where you unplug. This one happened to have a bunch of tape wrapped around it so uncover the tape to get to the connection harness. It is kind of hard to see but there is a little latch on the top. Push down on it and it should pop apart. 00:39
