Today on our 2011 Dodge Ram 1500 Pickup, were going to install a Draw-Tite Hitch, part number 75662. Here are some measurements that will assist you with selecting accessories for you new hitch. From the center of the hitch pinhole to the outermost point of the bumper is 2-1/2. From the top of the receiver tube to the ground is 20-1/2.Now, lets go ahead with the installation. Weve already gone ahead and removee the spare tire. Next we need to remove the bumper ball-mount cap.
Were simply going to take a flat weighted screwdriver, get underneath the cap so that we can remove it. Now we can take our 3/4 bolt, a conical tooth washer with the teeth of the washer facing the bumper and drop them through the bumper hole. Now we can go ahead and slide our hitch into position. Then well go ahead and slide the 3/4 lock nut into place. We'll go ahead and finger tighten the 3/4" bolt to hold our hitch in place.
Now we need to go ahead and install the hardware for our two forward fasteners. Our two forward fasteners are here, forward to the hitch, just in front of the bumper bar. Were taking our pull wire which is in supply with our install kit, feeding in through these attachment points to the outer end of the tube of the bumper bar. Once our pull wire is in position, well go ahead and take our 1 pipe, 3 block, and our 1/2" carriage bolt, well slide the block onto our pull wire then thread on our bolt. Now, well go ahead and slide both of them up into the bumper bar tube, pulling them into the position with our pull wire.
With that in place Ill go ahead and remove the pull wire, then well install the conical tooth washer with the teeth of the washer facing the hitch and our 1/2" nut. And again well just go hand tight until we get all fasteners in place. Now, well go ahead and repeat the same process for the passenger side. Now with all our fasteners installed, well go ahead and tighten them down. Now with all our fasteners tightened down, well go ahead and torque to specifications as indicated in the instructions, and with all our fasteners torque to specifications, well go ahead and re-install the spare tire, and that will complete the installation of our Draw-Tite hitch, part number 75662 on our 2011 Dodge Ram 1500..
Trailer Hitch Installation - 2006 Dodge Ram - Curt
Today on our 2006 Dodge Ram pickup, we'll be installing the Curt Hitch, part number 13333. Next, we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 1-3/4". From the top of the receiver tube opening to the ground is 19-1/2". This will assist you in selecting accessories such as a ball mount, bike rack, or cargo carrier. Now let's go ahead with installation.
Trailer Hitch Installation - 2013 Dodge Ram - Curt
Today in our 2013 Dodge Ram Pickup well be installing the Curt Hitch, part number 13333. Thats what our hitch to look like once its installed. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 2 inches. On the top or the inside of the receiver tube opening to the ground in 19 inches, this will assist you in selecting accessories such as a ball mount, a bike rack, or cargo carrier. Now, lets go ahead with installation.
Trailer Hitch Installation - 2007 Dodge Ram - Curt
Today on this 2007 Dodge Ram pickup, were going to install part number C15572 from Curt. This is what the hitch looks like when its installed on the truck. Next well go ahead and give you some measurements that will help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be 21 3/8 inches, and from the center of the hitch pin hole to the outside edge of the bumper is going to be 2 inches. Now well go ahead and show you how the hitch is installed. The first thing were going to do is lower the spare tire to get that out of the way.
Trailer Hitch Installation - 2007 Dodge Ram - Curt
All right, today on this 2007 Dodge Ram Pickup, we're going to install part number 13374 from Curt. All right, this is what the hitch looks like once it's installed on the truck. Next, we'll go ahead and give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper is going to be 2-1/2 inches. From the top of the receiver opening down to the ground is going to be 21 inches. Now, we'll go ahead and show you how the hitch is installed.
