Today on this 2011 Chevrolet HHR were going to install part number 24756 from Draw Tite. And this is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the pin hitch hole to the outer most point of the bumper is going to be 6, and from the top of the receiver opening down to the ground is going to be 10-1/2. Next well go ahead and show you how the hitch is installed. First thing we need to do is go ahead and lower the exhaust on the drivers side.
We will start off by using a spray lubricant on rubber hangers to make them easier to remove. We are going to use a simple pry bar to pry it off. Next I am going to show you where the attachment holes are going to be. Lets go ahead and use this hole right here, and also this hole here, and this will be identical on both sides of the vehicle. We just got done looking at the passengers side.
This hole here we are going to have to drill out to accept our half inch bolt, and on our drivers side bolt hole we dont have to do any drilling here. Lets go ahead and start installing the hardware. We will take the provided bolt leader, put it through the hole were going to use and over to this oval hole here as one of the attaching points. Next well take our block, thread it, push into the frame, and then we will thread in our carriage bolt, we will push everything inside and pull it out the hole. From the large oval hole to install our fasteners, we are going to take the bolt and the block, push it into the frame and pull it back down through the same hole.
Then we will repeat the same process back over on the drivers side. Alright now at this point we can go ahead and install the hitch, what we are going to do is take one half of the hitch over the muffler, use that to hold it up, and then we are going to install fasteners on the passengers side. With our hardware installed we will hand tighten down the bolts, and then we will tork them down as specified in the instructions. At this point we can go ahead and reinstall the exhaust. And with that that will finish it for our install of part number 24756 from Draw Tite.
.
Trailer Hitch Installation - 2011 Chevrolet HHR - Hidden Hitch
Today on our 2011 Chevy HHR well be installing hidden hitch, part number 60815. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is six and three-quarter inches. From the top of the receiver tube to the ground is nine and three-quarter inches. This will assist you with selecting accessories such as a bike rack or a cargo carrier.
Trailer Hitch Installation - 2010 Chevrolet HHR - Draw-Tite
Today on this 2010 Chevrolet HHR, we're going to install part no. 24756 from Draw Tite. This is what the hitch looks like when it is installed on a vehicle. Next we will give you some measurements that will help you out in selecting some accessories such as a bike carrier or a cargo carrier. From the center of the hitch pin hole to the outside edge of the bumper we're looking at 5 and 3/4 inches and from the top of the receiver openning down to the ground will be 10 and 3/8. Now we'll go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2010 Chevrolet HHR - Curt
Today on this 2010 Chevrolet HHR we are going to do an install part number 11447 from Curt. This is what the hitch looks like when its installed in the vehicle. Next well give you some measurements thatll help you out in selecting some accessories such as a bike carrier or a cargo carrier. From the top of receiver opening down to the ground is going to be 10 3 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5 inches. Now we will show you how the hitch is installed. Our first step is go ahead and lower the exhaust, We will spray down the hangers with some lubricant and go ahead and remove them.
Trailer Hitch Installation - 2006 Chevrolet HHR
Today were working on a 2005 Chevy HHR. Were going to install a Curt Hitch part number 11447. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the pin hitch hole to the outer most point of the bumper is 5-3/4 inches, and from the top of the receiver tube to the ground is 11 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. Now lets go ahead with the installation.
Trailer Hitch Installation- 2009 Chevrolet HHR
Today we are going to be working on a 2009 Chevy HHR. We will be installing Curt hitch part number 11447. Here are a couple of measurements that will assist you in ing accessories for your new hitch. From the center of the hitch pin hole to the outermost point on the bumper is 6- ½ inches. From the top of the receiver tube to the ground is 10- ¾ inches. This will assist you in ing accessories such as a bike rack, cargo carrier, or draw bar. Now let us go ahead with the installation. 0:31
