Today on our 2012 Nissan Murano, well be installing the Draw Tide Hitch, part number 75647. Here are a couple of measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch, pinhole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube to the ground is 14 inches. This is assist you with selecting accessories, such as soon as draw bar, a bike rack, or a cargo carrier. Now, lets go ahead with installation.
Before we can install our hitch, well need to lower the exhaust. Before I do that, Im go ahead and take my safety strap and route it underneath the exhaust. So we can control how far and fast the exhaust will fall. To lower the exhaust, well take a little spray lubricant and spray each of the four hangers that well need to remove. But we got one on the passenger side, two on the driver side and one of the exhaust pipe just behind the differential.
Next, on most applications, they're be a piece of plastic trim between the bumper fascia and the bumper beam. Youll need to remove the two plastic push pens to remove this inside trim piece. For our application, this trim piece has already been removed. Next, lets go ahead and point out our attachment points in the frame. We have three on the driver side and two on the passenger side.
The forward fastener on the driver side will be a ten-millimeter bolt and inaudible tooth washer. The other four attachment points will all be a 12 millimeter bolts with inaudible tooth washers. Now, before we attempt to install our fasteners, we're going to want to clean out the threads of each of the attachment points. To do this, well take a little spray lubricant and spray down each of the well nuts in the frame. Then take our half-inch nylon tool brush, part number, 814092 and thoroughly clean out the threads that can build up with dust, dirt, and debris.
Quick tech tip, I also recommend to take one of the new fasteners and go ahead and thread it into the well nut just to make sure itll go nice and easily. Now, we're ready to go ahead and install the hitch. It's a good idea to get an extra set of hands to help you hold the hitch in place while you install your fasteners. Now, with all our fasteners installed finger tight, we can go ahead and run them down. With all our fasteners secured, well now go ahead and tort to specification as indicated in the instructions. Well go ahead and take the two cable or zip ties that are provided with our install kit and secure the rear fascia to the hitch. We can go ahead and reinstall the exhaust. And with that completed, this will complete the install of our Draw Tide Hitch, part number, 75647 on our 2010 Nissan Murano.
Trailer Hitch Installation - 2013 Nissan Murano - Curt
Today on our 2013 Nissan Murano we'll be installing the Curt Hitch, part number 13577. This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube opening to the ground is 15-1/4 inches. This will assist your selecting accessories such as a ball mount, a bike rack or cargo carrier.
Trailer Hitch Installation - 2013 Nissan Murano - Hidden Hitch
Today on our 2013 Nissan Murano we'll be installing the Hidden Hitch, part number 87486. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 5-1/2 inches.From the top of the receiver tube to the ground is 15-1/2 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier. Now we'll go ahead with installation.
Trailer Hitch Installation - 2013 Nissan Murano - Draw-Tite
Today on our 2013 Nissan Murano we'll be installing the Draw-Tite Hitch, part number 75647. This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 5-1/2 inches. From the top of the receiver tube to the ground is 15-1/2 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier.Now we'll go ahead with installation.
Trailer Hitch Installation - 2013 Nissan Murano - Bosal
Today on our 2013 Nissan Murano, well be installing the Bosal Hitch, part number bsl047173. This is what our hitch will look like once its installed. Now well go ahead with our install. To begin our install, well first need to lower the exhaust. To lower the exhaust there are four rubber isolators that will need to be removed. However, before we lower the exhaust, were going to put a safety strap underneath so that we can safely lower the weight of the exhaust.
Trailer Hitch Installation - 2013 Nissan Murano - Bosal with Receiver
Today on our 2013 Nissan Murano, well be installing the Bosal Hitch part number BSL047173-964. Well also be installing the removable receiver attachment. This is what our hitchll look like once installed and this is what itll look like once we install the removable receiver attachment. Now well go ahead and give you a couple measurements. From the center of the hitch pin hole to the outermost edge of the bumper is three inches. From the top of the receiver tube opening to the ground is 13 inches.
Trailer Hitch Installation - 2013 Nissan Murano - Bosal with Euro Ball Mount
Today on our 2013 Nissan Murano, well be installing the Bosal hitch, part number bsl047173-004. Well also be installing the European style or Swan Neck Ball mount attachment. This is what our hitch will look like once its installed and this is what it looks like once we install the European Style or Swan Neck Ball mount. Next well go ahead and give you a couple of measurements to assist you with selecting accessories with your European Style or Swan Neck attachment. From the nearest point of the bumper to the nearest point of the ball is two inches. From the bottom of the ball to the ground is 17.
