Today on this 2010 Hyundai Santa Fe, were going to install part number 85754 from Hidden Hitch. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.
Before we install our hitch, well take a few minutes to clean out those threads. Well go ahead and spray down the weld nuts with some lubricant and then clean them out with a tube brush. Well be using part number 814092. Well go ahead and use one of the hitch bolts to make sure the threads are cleaned out. Once we can run the bolt in and out easily then well go ahead install the hitch.Now to install the hitch, well take the bolt and the conical tooth washer, well install it to the hitch and then into the weld nuts in the frame.
You want to make sure that the little teeth on the conical tooth washer are facing towards the hitch. You definitely want to have an extra set of hands to help hold up the hitch while you install it on the frame. Once you have all four fasteners installed in the frame, well go ahead and snug them down and then torque the bolts down as specified in the instructions. With all the bolts torqued down, thatll finish it for our install of part number 84574 from Hidden Hitch.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Hidden Hitch
Today on our 2012 Hyundai Santa Fe we'll be installing Hidden Hitch, part number 87574. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 4 inches. From the top of the inside of the receiver tube opening to the ground is 12 3/4 inches. This will assist you when selecting accessories such as a ball mount, a bike rack, or a cargo carrier.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Draw-Tite
Today on our 2012 Hyundai Santa Fe we'll be installing the Draw-Tite hitch, part number 75684. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 4 inches. From the top of the inside of the receiver tube opening to the ground is 12 3/4 inches. This will assist you when selecting accessories such as a ball mount, a bike rack, or a cargo carrier.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Draw-Tite
Today on our 2012 Hyundai Santa Fe well be installing the Draw Tite hitch, part number 36511. Next well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is three and a half inches. From the top of the inside of the receiver tube opening to the ground is 13 inches. This will assist you with selecting accessories such as a bike rack or cargo carrier. First before we install the hitch well go ahead and point out the attachment points.
Trailer Hitch Installation - 2011 Hyundai Santa Fe - Hidden Hitch
Today on our 2011 Hyundai Santa Fe, we're going to install Hidden Hitch, part number 90212. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.
