Today on this 2010 Hyundai Santa Fe, were going to install part number 75684 from Draw-Tite. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.
Before we install our hitch, well take a few minutes to clean out those threads. Well go ahead and spray down the weld nuts with some lubricant and then clean them out with a tube brush. Well be using part number 814092. Well go ahead and use one of the hitch bolts to make sure the threads are cleaned out. Once we can run the bolt in and out easily then well go ahead install the hitch.Now to install the hitch, well take the bolt and the conical tooth washer, well install it to the hitch and then into the weld nuts in the frame.
You want to make sure that the little teeth on the conical tooth washer are facing towards the hitch. You definitely want to have an extra set of hands to help hold up the hitch while you install it on the frame. Once you have all four fasteners installed in the frame, well go ahead and snug them down and then torque the bolts down as specified in the instructions. With all the bolts torque down, thatll finish it for our install of part number 75684 from Draw-Tite.
Trailer Hitch Installation - 2013 Hyundai Santa Fe - Curt
Today on our 2013 Hyundai Santa Fe well be installing the Curt hitch, part number C13134. Before we begin our install heres what the hitch looks like when its installed on the vehicle. Well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the inside of the receiver tube opening to the ground is 12 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Curt
Today on our 2012 Hyundai Santa Fe well be installing the Curt hitch, part number C13073. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is four and a half inches. From the top of the receiver tube to the ground is 15 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2011 Hyundai Santa Fe - Draw-Tite
Today on our 2011 Hyundai Santa Fe, we're going to install the Draw-Tite Hitch, part number 36511. This is what our hitch will look once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.
Trailer Hitch Installation - 2008 Hyundai Santa Fe
Today on this 2008 Hyundai Santa Fe, we're going to install part number 87414 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 13 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5-3/4 inches. First thing we'll do is we'll show you where the hitch mounts up to the frame as these two existing threaded holes here. Next step is to go ahead and clean up the threaded holes.
