Today on this 2010 Honda Civic were going to install part number 24763 from Draw Tite. Alright this is what the hitch looks like when it is installed. Next well give you some dimensions that will help you out when choosing accessories. From top of receiver opening down to ground were looking at 11-3/4 inches, and from the center of the pin hitch hole to the outside edge of the bumper on this vehicle is going to be 2-1/2 inches. Now I will go ahead and show you how the hitch is installed. There is one hanger right above the tail pipe; well spray it down with some lubricant to make it a little easier to move.
Alright so we use a pry bar to move it off. Alright next we need to remove the heat shield right here. There are 4 bolts we have to remove, but it will go back up once we are done. Alright here is one last fastener right here we have to remove for the heat shield. The next step is to remove this plastic rib bit.
That will give us a little bit more working room when we install the hitch. Now I can start installing the hitch. What we will do first is attach the hitch to the tow loop. That will help hold it while we put the rest of the hardware in place. We will take our u-bolt and put it around the tow loop, and put the hitch up.
Alright now the hitch is going to line up with this existing hole right here in the frame, and well use this handle nut to put it on the inside and run our bolt into. Well have a conical tooth washer and a bolt going through the hitch, and to the handle nut. The drivers side is done, lets go ahead and repeat the same process over on the passengers side. Alright when you put the hitch up, make sure the hitch stays below the two hangers for the tail pipe so it will all go up like one assembly. With all the hardware installed lets go ahead and tighten down the bolts, and then tork them down as specified in the instructions.
Alright now I can go ahead and put the heat shield back into place. Okay our heat shield is in place, the last thing I do is reinstall the muffler onto the rubber hanger. And there you have it for part number 24763 from Draw Tite on a 2010 Honda Civic. .
Trailer Hitch Installation - 2007 Honda Civic - Curt
Today on our 2007 Honda Civic, we'll be installing the Curt Hitch part number 11437. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 3 inches. From the top of the receiver tube to the ground is 10-3/4 inches. Those will assist you with selecting accessories such as a bike rack or a cargo carrier.
Trailer Hitch Installation - 2012 Honda Civic - Curt
Today, on our 2012 Honda Civic, well be installing the Curt Hitch part number 11437. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outer most edge of the bumper is 3 inches. From the top of the receiver, tube to the ground is 11 inches. This will assist you with selecting accessories such as a bike rack or cargo carrier.Now, lets go ahead with the installation.
Trailer Hitch Installation - 2012 Honda Civic - Hidden Hitch
Today on this 2012 Honda Civic Hybrid we'll be installing the Hidden Hitch, part number 60822. Here are a few measurements that will help when selecting accessories for your new hitch such as a bike rack or cargo carrier. From the center of the hitch pin hole to the edge of the bumper will be 4 inches and from the top of the receiver tube to the ground will be 11 inches. Now we'll go ahead with our install. To begin our install, we'll need to remove the plastic shroud on the driver's side. There are four pushpins and three 10-mm bolts holding it up.
Trailer Hitch Installation - 2012 Honda Civic - Draw-Tite
Today on this 2012 Honda Civic Hybrid we'll be installing the Draw-Tite Hitch, part number 24763. Here are a few measurements that will help when selecting accessories for your new hitch such as a bike rack or cargo carrier. From the center of the hitch pin hole to the edge of the bumper will be 4 inches and from the top of the receiver tube to the ground will be 11 inches. Now we'll go ahead with our install. To begin our install, we'll need to remove the plastic shroud on the driver's side. There are four pushpins and three 10-mm bolts holding it up.
Trailer Hitch Installation - 1994 Honda Civic
Today on this 94 Honda Civic, were gonna install part number 24677 from Draw-Tite. This will also apply to part number 60834 from Hidden Hitch. Alright, this is what the hitch looks like when its installed in the car. Next well give you some measurements thatll help you out in selecting your accessories. From the top of the receiver opening down to the ground is going to be 11 3/8, from the center of the hitch pinhole to the outside edge of the bumper is going to be 2 inches. Now well go ahead and show you how the hitch is installed.
