Today on this 2010 Chevrolet HHR we are going to do an install part number 11447 from Curt. This is what the hitch looks like when its installed in the vehicle. Next well give you some measurements thatll help you out in selecting some accessories such as a bike carrier or a cargo carrier. From the top of receiver opening down to the ground is going to be 10 3 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5 inches. Now we will show you how the hitch is installed. Our first step is go ahead and lower the exhaust, We will spray down the hangers with some lubricant and go ahead and remove them.
Alright, with the exhaust out of way we can see where the hitch mounts up. We will use this existing hole right here however we have to enlarge it -inch to make it easier run and pull the bolt all the way through. And this will be our access hole and also as an attachment point and this will be identical on both sides. To install our hardware we run our bolt leader to the hole we drilled out and out the access hole. Take your block, thread it in and then well tread on the bolt.
Push it all inside. Now it may help to tilt it head first and then push it in. Now for this attachment hole, we are going to pre-assemble everything outside and then we are going to take everything and push it inside the frame and then pull back out. Were gonna repeat the same process over on the driver side. And now from this point we can go ahead and install the hitch.
Well take the driver side of the hitch lay it on top of the muffler and then push it to the passenger side up to the frame. Well line up the bolts and install the French nuts. Now we can go ahead and snug everything down. With everything tightened down, we will torque down the bolts as specified in the instructions. With all the hardware torqued down, we can go ahead and reinstall the exhaust.
And with that that will finish for our install of part number 11447 from Curt on a 2010 Chevrolet HHR.
Trailer Hitch Installation - 2011 Chevrolet HHR - Hidden Hitch
Today on our 2011 Chevy HHR well be installing hidden hitch, part number 60815. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is six and three-quarter inches. From the top of the receiver tube to the ground is nine and three-quarter inches. This will assist you with selecting accessories such as a bike rack or a cargo carrier.
Trailer Hitch Installation - 2010 Chevrolet HHR - Draw-Tite
Today on this 2010 Chevrolet HHR, we're going to install part no. 24756 from Draw Tite. This is what the hitch looks like when it is installed on a vehicle. Next we will give you some measurements that will help you out in selecting some accessories such as a bike carrier or a cargo carrier. From the center of the hitch pin hole to the outside edge of the bumper we're looking at 5 and 3/4 inches and from the top of the receiver openning down to the ground will be 10 and 3/8. Now we'll go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2011 Chevrolet HHR
Today on this 2011 Chevrolet HHR were going to install part number 24756 from Draw Tite. And this is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the pin hitch hole to the outer most point of the bumper is going to be 6, and from the top of the receiver opening down to the ground is going to be 10-1/2. Next well go ahead and show you how the hitch is installed. First thing we need to do is go ahead and lower the exhaust on the drivers side.
Trailer Hitch Installation - 2006 Chevrolet HHR
Today were working on a 2005 Chevy HHR. Were going to install a Curt Hitch part number 11447. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the pin hitch hole to the outer most point of the bumper is 5-3/4 inches, and from the top of the receiver tube to the ground is 11 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. Now lets go ahead with the installation.
Trailer Hitch Installation- 2009 Chevrolet HHR
Today we are going to be working on a 2009 Chevy HHR. We will be installing Curt hitch part number 11447. Here are a couple of measurements that will assist you in ing accessories for your new hitch. From the center of the hitch pin hole to the outermost point on the bumper is 6- ½ inches. From the top of the receiver tube to the ground is 10- ¾ inches. This will assist you in ing accessories such as a bike rack, cargo carrier, or draw bar. Now let us go ahead with the installation. 0:31
