Today in this 2007 Honda Odyssey we will be installing the Draw-Tite hitch part number 75270. Next we will go ahead and give you a couple of measurements this is what are hitch looks like once it is installed from the center of a hitch pin hole to the outermost edge of the bumper is 5 inches from the top of the receiver tube to the ground is 12 and three quarter inches this will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier now lets go ahead with the installation our first step is going to be to lower the exhaust there are two rubber ice slathers that it need to be remove to o this well first spray them down with some spray lubricant and then remove the rubber from the ice hanger. Alright with the exhaust hangers remove well now move on to our attachment points were going to have three on each sides. Each of this attachment points will be a well nut in the frame heres a rear most of the attachment points are center and the forward most attachment points. Before we try and install our hitch and new hardware. We want to go ahead and clean each one of this well nut out over time theyll build up with dirt, dust and debris and become corroded with rust.
To clean them out we use some spray lubricant and a half inch nylon toothbrush part number 814092 each process we do in here on the driver side is going to be repeat identically on the passenger side now were ready to go ahead and install the hitch. To secure the hitch well be using the inch and a half by two inch blocks the block will get some which between the hitch and the frame to secure. It will be using the new 12 millimeter bolts and conical tooth washers to the teeth of the washer facing the hitch. Its a good idea to get an extra set of hands to help you hold the hitch in place as you install your fasteners quick tech tip fit the fasteners side up over the exhaust and then bring the driver side up in the position. Now with all our fasteners installed we can go ahead and tighten them down.
Once youve got them tighten down well go ahead towards the specification as indicated in the instruction now we go ahead in reinstall the exhaust. And with our exhaust reinstalled that will complete the install of our draw type hitch part number 75270 on our 2007 Honda Odyssey. .
Trailer Hitch Installation - 2013 Honda Odyssey - Hidden Hitch
Today on this 2013 Honda Odyssey, were going to install part #87479 from Hidden Hitch. This is what the hitch looks like once its installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories, such as a bicycle rack, a ball mount, or a cargo carrier. From the top of the receiver opening down to the ground will be about 12 inches. From the center of the hitch pinhole to the edge of the bumper will be about 6-1/2 inches. Now, well go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2008 Honda Odyssey - Hidden Hitch
Today on this 2008 Honda Odyssey were going to install part number 87479 from Hidden Hitch. This is what the hitch looks like when its installed on the van. Next well give you some measurements that will help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 12 inches. From the center of the hitch pin hole to the edge of the bumper will be about five and a quarter inches. Now Ill go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2009 Honda Odyssey - Curt
Today on our 2009 Honda Odyssey, we're gonna be installing the Curt hitch part number C12031. This is what a hitch looks like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 3 inches. From the top of the receiver tube to the ground is 13 and 3/4 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2009 Honda Odyssey - Hidden Hitch
Today on our 2009 Honda Odyssey, we're gonna be installing the hidden hitch part number 90153. Before we begin installation, we'll go ahead and lower the exhaust. To lower the exhaust, we'll use a little spray lubricant on the rubber isolator for the rear exhaust hanger. Then we can simply take our crowbar and just remove the isolator from the metal hanger. This point, we can go ahead and point out then attach the points here in the frame. Next, we'll go ahead and take our half-inch nylon tube brush part number 814092 and some spray lubricant to clean up the weldnuts in the frame.
Trailer Hitch Installation - 2009 Honda Odyssey - Draw-Tite
Today on our 2009 Honda Odyssey, we'll be installing a draw-tite hitch part number 36417. Before we begin installation, we'll go ahead and lower the exhaust. To lower the exhaust, we'll use a little spray lubricant on the rubber isolator for the rear exhaust hanger. Then we can simply take our crowbar and just remove the isolator from the metal hanger.This point, we can go ahead and point out then attach the points here in the frame. Next, we'll go ahead and take our half-inch nylon tube brush part number 814092 and some spray lubricant to clean up the weldnuts in the frame. After you finish cleaning up the weldnut, I recommend you to take the 12mm bolts and go ahead and drive it in to the weldnut to make sure it goes nice and smoothly.
