Today on this 2011 Chrysler Town and Country, were going to install part number 13364 from Curt. This is what the hitch looks like once installed on the van. Next, well give you some measurements to help you out in selecting some accessories such as the ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin to the edge of the bumper is going to be four and a quarter inches. will be 12 and three quarter inches. From the center of the hitch pin opening to the bumper will be five and three quarter inches.
Now Ill go ahead and show you how the hitch is installed. The first step is go head and lower the exhaust. Well remove the exhaust hangers from the first three hangers starting from the muffler and work on the way back. Well also use the strap to hold the exhaust in place and control it while we lower it. Well also spread the hangers down with some lubricant to make it a little easier to remove.
Drill the also the grounds that need to be removed for exhaust. Next, well go ahead and remove the inboard fasteners located on both sides of the frame. These fasteners will not be reused. Next, wed go ahead and install the hitch. We loosely install the rear board fasteners.
Well be using the eight millimeter bolts with the conical toothed washer and nut. When we install the conical toothed washer we want to make sure that the teeth are facing towards the bumper bracket. Well snuck one of the bolts on each side down to bring the hitch closer to the bottom of the frame then well use the hitch in the tin plate to drill the half in its hole for our fasteners to go towards the front. When the holes drilled out, well go ahead and loosen up the hitch with the fasteners that are previously installed. Well the swing the hitch down a little bit so we can start the handle nut into the access hole that is located at the bottom of the frame.
And then well go ahead and push the hitch in position and install the hardware. Itll be the half inch bolt for the conical toothed washer. Now, all the fasteners installed, well go ahead and tie them down and then torque them down as specified in the instructions. And then we can go ahead and reinstall the exhaust. And with that, thatll finish it for install part number 90333 from Hidden Hitch on our 2004 Dodge Intrepid. .
Trailer Hitch Installation - 2004 Dodge Intrepid - Draw-Tite
Today on this 2004 Dodge Intrepid, were going to install part number 36268 from Draw-Tite. This is what the hitch looks like once installed in the vehicle. Next, well go ahead give you some measurements to help you out in selecting some accessories such as the bicycle rack or a cargo carrier. From top of the receiver opening down to the ground will be 12 and three quarter inches. From the center of the hitch pin opening to the bumper will be five and three quarter inches. Now Ill go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2002 Dodge Intrepid - Hidden Hitch
Today, on this 2002 Dodge Intrepid, well be installing a Hidden Hitch, part number 90333. Next, well give you a couple of clearance measurements. From the center of the hitch pin hole to the furthest point of our bumper measures 6-1/4 inches. We have 14 inches of ground clearance from the top of the inside of the receiver tube to the ground. These measurements can come in handy when selecting accessories for your hitch like a cargo carrier or a bike rack. The first thing we need to do is lower the exhaust to give us working room for our hitch.
Trailer Hitch Installation - 2002 Dodge Intrepid - Draw-Tite
Today on this 2002 Dodge Intrepid well be installing the draw type hitch part number 36268. Next, will give you a couple of clearance measurements. From the center of the hitch pinhole to the furthest point of our bumper measures 6-1/4 inches. We 14 inches of ground clearance form the top of the inside of the receiver tube to the ground. These measurements can come in handy when selecting accessories for your hitch like your cargo carrier or a bike rack. The first thing we need to do is lower the exhaust to give us working room for our hitch.
