Alright, today on this 2002 Toyota Tundra, well going to install part number 75105 from Draw-Tite. This is what the hitch looks like once its installed on the truck. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin opening to the edge of the bumper is going to be 4 inches and from the top of the receiver opening down to the ground will be 20 inches. Now well go ahead and show you how the hitch is installed.First thing we need to do is go ahead and locate the threaded holes that are in the frame. Well spray them down with lubricants first.
Well be using two brush cleaners to clean up the threads part number 814092. Now the older the vehicle is the hardest it will be to clean out. Well use a brush and lubricant and then test fit with one of the hitch bolts. If that doesnt work, then you may need to use as a tap to help clean up the threads. Alright, after every threads cleaned out, we can go ahead and lift the hitch up in position.
Now well go ahead and get an extra set of hands and hold the hitch to install the hardware. Well install our threaded bolts with the conical tooth washers on our threaded holes to hold the hitch up and then well go ahead and move to the very back of the vehicle and install another set of hardware. Youll have the block and the carriage bolt and put that on top of the frame down to the hitch then install a flange nut on to the bottom. Now with all our hardware installed, we can go ahead and tighten down all the bolts and then torque the bolts down as specified in the instructions. And with that, thatll finish it for our install or part number 75105 from Draw-Tite on our 2002 Toyota Tundra..
Trailer Hitch Installation - 2013 Toyota Tundra - Hidden Hitch
Today on our 2013 Toyota Tundra we'll be installing Hidden Hitch, part number 87434.This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple ofmeasurements to assist you with selecting accessories for your new hitch. From the centre of thehitch pin hole to the outermost edge of the bumper is 1. From the top of the inside of the receivertube opening to the ground is 18. This will assist you in selecting accessories, such as a ball mount,bike rack or cargo carrier. Now lets go ahead with installation.First we'll need to remove the angle brackets that are located on the inside of the framerail, near thebumper on both sides.
Trailer Hitch Installation - 2013 Toyota Tundra - Draw-Tite
Today on our 2013 Toyota Tundra, we'll be installing the Draw-Tite Hitch, part number 75527. This iswhat our hitch will look like once its installed.Next we'll go ahead and give you a couple of measurements to assist you with selecting accessoriesfor your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 1.From the top of the inside of the receiver tube opening to the ground is 18. This will assist you inselecting accessories such as a ball mount, bike rack, or cargo carrier. Now lets go ahead withinstallation.First we'll need to remove the angle brackets that are located on the inside of the frame rail near thebumper, on both sides. To remove the brackets, there are a total of four fasteners for each.
Trailer Hitch Installation - 2013 Toyota Tundra - Draw-Tite
Today on our 2013 Toyota Tundra well be installing the Drawtite Ultra frame hitch part #: 41935. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is two inches. From the top of the receiver tube opening to the ground is 18 and a quarter inches. This will assist you with selecting accessories such as a ball mount, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2013 Toyota Tundra - Curt
Today on our 2013 Toyota Tundra we'll be installing the Curt Trailer Hitch, part number 13198. This is what our hitch will look like once it's installed. Next, we'll give you a couple measurements to assist you selecting accessories for your new hitch. The center of the hitch pin hole is even with the outer edge of the bumper, and top of the receiver tube opening to the ground is 18". This will assist you selecting accessories such as a ball mount, a bike rack, or cargo carrier. Now let's go ahead with installation.
Trailer Hitch Installation - 2001 Toyota Tundra - Hidden Hitch
Today on our 2001 Toyota Tundra we'll be installing the Hidden Hitch part number 87588. This is what our hitch will look like once installed. Next we'll go and give you a couple of measurements to assist you in selecting accessories to your new hitch. Such as the draw bar, a bike rack a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/4 inches. From the top of the receiver tube to the ground is 19 inches.
