All right, today on this 2001 Pontiac Montana, we're going to install part number 87410 from Hidden Hitch. All right, this how the hitch will look like when it is installed on the vehicle. Next we'll give you some measurements to help you out in selecting for accessories, such as a boat mount, a bicycle rack or cargo carrier. From top of receiver opening down to ground is going to be 12-1/2 inches. And from the center of the hitch pin hole to outside the edge of the bumper is going to be 4-1/4 inches. Now we're going to show you how the hitch is installed.
First step is go ahead and loosen up the vehicle exhaust on the passenger side. Then we'll go ahead and remove one of the bolts for the compressor on the driver's side. Then we'll go ahead and raise the hitch into position where we'll be using M10 Bolts to hold the hitch up. All right, with the hitch secured to the vehicle now, we'll go ahead and use the hitch as a template to draw on our holes. We'll use 1/2-inch drill bit to mark the center of our holes.
Then we'll drill it out with a inaudible, then go back at it with a 1/2-inch bit. We'll now go ahead and remove the hitch. We'll allow the compression bracket to fall down a little bit, then we'll go ahead and slip the hitch between the compressor bracket and the frame, and then reinstall the hardware. Now we'll move back over to the driver's side and reinstall the bracket for the exhaust onto the new hardware. All right, now we'll go ahead and start installing the hardware at the end of the frame.
We'll take one of the handle nuts, bend it into kind of an "S" shape, and we'll take our handle nut and install it through the slot on the side of the frame, to line it with the hole that we've drilled out. Then we'll install the 1/2-inch bolt, and the lock washer from the bottom and do it on both sides of the frame. Okay, and now we'll move on to our last fastener on our passenger side, we'll fish wire the carriage bolt and the square block on the inside frame. Then we'll have two more square blocks underneath the hitch and then the lock washer and nut. Alright, if all our hardware is loosely installed, then we'll go ahead and tighten down all our bolts, then torque them down as specified in the instructions.
With that, that will finish the install for part number 87410 from Hidden Hitch, on our 2001 Pontiac Montana.
Trailer Hitch Installation - 2001 Pontiac Montana - Draw-Tite
Today, on this 2001 Pontiac Montana we are going to install part number 75278 from Draw Tite. This is what the hitch looks like when it is installed on a vehicle. Next, we will give some measurements to help you out with selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From top of receiver opening down to the ground is going to be 12-1/2 inches and from the center of the hitch pinhole to the outside edge of the bumper, is going to be 4-1/4 inches. Now, I will go ahead and show you how the hitch is installed. The first step is to go ahead and loosen up the vehicle exhaust on the passenger side.
Trailer Hitch Installation - 2006 Pontiac Montana - Curt
Today on our 2006 Pontiac Montana well be installing the Curt Hitch part number 13344. This application does come with the manufacturers load leveling system that will need to be modified on the drivers side. Here are a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 6 inches. From the top of the receiver tube to the ground gives you 12-3/4 inches. This will assist you with selecting accessories.
Trailer Hitch Installation - 2006 Pontiac Montana
Today we will be working on a 2006 Pontiac Montana. We will be installing Hidden Hitch part number 87410, comparable to Draw-Tite part number 75278. Here are a couple of measurements that will assist you with ing accessories for your new hitch. From the center of the hitch pin hole to the outer most point of the bumper is 5-1/2 inches. From the top of the receiver tube to the ground is 12 inches. This will assist you with ing accessories such as a draw bar, a bike rack or a cargo carrier. Now let us go ahead with the installation. 0:33
Trailer Hitch Installation - 2002 Pontiac Montana
Today we are working on a 2002 Pontiac Montana, we will be installing Hidden Hitch part number 87410. This will also be comparable to Draw-Tite hitch part number 75278. Here are a couple measurements that will assist you in ing accessories for your trailer hitch. Items such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube to the ground is 11-1/4inches. Now lets go ahead with the installation. :32
Trailer Hitch Installation - 2006 Pontiac Montana
Today on this 2006 Pontiac Montana, we will be installing Curt hitch part number 13336. OK, we are underneath the vehicle and the first thing we have done is gone ahead and lowered the spare tire. Get it out of our way. We are looking at the passenger side frame rail. We can go ahead and point out the mounting holes we are going to be using for our trailer hitch. You can see here at the bottom of the frame, we have two bolts holding the exhaust hanger onto the frame. We are going to lower those down and those are going to provide our two rearmost attaching points. And just forward of that, there is a fascia support that is held in with another bolt. And we are going to remove that bolt as well and that will provide our third attaching point. If you go to the vertical side of the inboard part of the frame, you can see we have a hole here. That is going to provide our fourth attaching point. At this location, we are actually going to fish wire a 7/16 carriage bolt, along with the carriage block, into position. 0:42
