Today with our 2011 Toyota Sienna, we are going to show you the Thule Revolver 4 bike rack, part number TH964. We will take the bike rack and fit it into our hitch, lining up the pin hole on the rack with the pin hole on our receiver. Next we will attach the included anti-rattle pin and lock. At the lowest point of the Thule Revolver, there are about 8-1/2 inches of ground clearance. The Thule Revolver measures 7-1/2 inches to the center of the hitch pin hole to the back of the upright bar. This allows enough clearance to clear the back bumper and back fascia of our 2011 Sienna. 0:37
When not in use, the arms of the Thule Revolver can be folded down to allow extra clearance behind the vehicle. We will place our bike into our cradles and pull the rubber straps to secure the bike. The Thule Revolver is a swing out bike rack. This is designed to swing away from the vehicle to allow access to the trunk or hatch. First, we will unlock it by backing off the gray hand knob down at the bottom. Then pull the pin from the arm and the entire bike rack will swing away from our vehicle. Now our bike and bike rack are both completely out of the way. We have complete access to our hatch and we did not have to remove the bike. And that does it for the Thule Revolver 4 on our 2011 Toyota Sienna, part number TH964.
Swagman Titan Hitch Bike Rack Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, we'll be test fitting the Swagman Titan 4 Bike Carrier both 1-1/4 and 2 inches hitches, Part Number S63410. Now to begin our test fit, we'll slide the bike rank shank using the included two inch adapter into the hitch, line up the hitch pin hole, and install and tighten down our anti-rattle bolt. With the bolt tight, our bike rack is secured to the vehicle. We'll now go ahead and give you a few measurements. Our ground clearance here at the back of the bike rack measures 13 inches and from the closest point of the bike rack, here at the mast to the back of the vehicle measures 8-1/2 inches. We can now go ahead and pull the switch here on the base of the rack, which will allow us to tilt the mast down and open the cargo door.
Kuat Sherpa Hitch Bike Rack Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, we'll be test fitting the Kua Sherpa Hitch Mounted 2 Bike Rack with Wheel Mount Cradles, Part Number S102. Now to begin our test fit, we'll slide the bike rack shank into the hitch, line up the hitch pin hole, and slide the hitch pin in. We can then move to the back of the shank where we can tighten that down securing the bike rack to the vehicle. We'll now and go ahead, and give you a few measurements. Our ground clearance here at the bottom of the bike rack is 11 inches and from the closest point of the bike rack with the bike rack in the stored position to the back of the vehicle measures 2-1/2 inches. We'll now go ahead and pull the handle and unfold the platform.
Kuat NV Hitch Bike Rack Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, well be test fitting the Kuat Aluminum Hitch Mounted Two Bike Rack with Wheel Mount Cradles. This is the Kuat NV, part number N101. To being our test fit, well slide the bike rack shank into the hitch, line up the hitch pin holes and slide the hitch pin in. Well then move to the back of the shank and tighten the anti-rattle knob down securing the bike rack to the vehicle. With that done, well go ahead and give you a few measurements. Our ground clearance here at the bike rack measures ten inches.
Yakima DoubleDown Ace Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna well be test fitting the Yakima DoubleDown Ace 4, part number Y02451. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin holes and use our securing pin to attach the bike rack. Then well use the hand knob at the base of the rack to tighten up and engage our anti-rattle lock. Now well go over a handful of clearance measurements. Weve got about 10 inches of ground clearance and about 3 inches of clearance between the closest part of the carrier and the closest part of the vehicle.
Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Thule Hitching Post Pro Hitch Mounted Bike Carrier, part number TH934XTR. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pin hole, thread in our anti-rattle bolt, and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 10 inches of ground clearance and about 5 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 15 inches of length to the rear of the vehicle.
Yakima SwingDaddy 4 Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Yakima SwingDaddy 4 Hitch Mounted Bike Carrier, part number Y02422. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pin hole, thread in our anti-rattle bolt and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 10 inches of ground clearance and about 1/2-inch of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 10 inches of length to the rear of our vehicle with the carrier's arms folded down.
