Today on our 2011 Toyota Camry, we'll be test fitting the Rhode Gear Highway 2 Bike Carrier, part number RG8015220. Now, our bike rack is already pre-assembled and our vehicle has an 1-1/4-inch hitch, so we're ready to go ahead and fit it to the vehicle. We'll insert the bike rack shank into the hitch. We'll line up the hitch pinhole and insert our anti-rattle bolt. We'll then tighten it down with a wrench. With the anti-rattle bolt tight, we can install our safety pin on the other side and that will secure our bike rack to the vehicle.
With our bike rack secured, we'll go ahead and give you a few measurements, and our ground clearance is 10 inches and from the closest point of the bike rack to the back of the vehicle is 5 inches. We'll now go ahead and show cargo access. We'll fold the bike rack down and open our deckled. We'll now go ahead and prepare the bike rack to load the bike. What we'll need to do is to undo the hook and loop straps exposing the cradles.
We'll then set the bike into the cradles and bring the hook and loop strap back through, securing it to the bike rack. And with our bike secured to the bike rack, we're ready to hit the road. And that will do it for our Rhode Gear Highway 2, part number RG8015220, on our 2011 Toyota Camry.
Yakima DoubleDown Ace Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry well be test fitting part number Y02451. This is the Yakima DoubleDown 4 Bike Carrier. Now to begin our test fit, well slide the bike rack shank into the hitch after removing the 2-inch adaptor. Well then install the attached hitch pin where we can then move to the back of the shank and tighten the knob securing our bike rack to the vehicle. Well now pull the handle here at the bottom of the bike rack mast to allow the mast to tilt down. We can then open our deck lid.
Thule Vertex 4 Hitch Bike Rack Review - 2007 Toyota Camry
Today, on our 2007 Toyota Camry, we'll be test fitting the Thule Vertex 4 bike carrier for both inch and a quart and 2 inch hitches, part number th9029.We're going to begin our test fit. We'll remove the 2 inch adapter. We can then slide in the bike rack shank to the hitch, line up the hitch pin hole and install and tighten down on our anti-rattle bolt. With our bolt tight, our bike rack can secure to the vehicle.Now, we'll go ahead and give you a few measurements. Now, the ground clearance at our bike rack is 9 1/2 inches, and from the closest point of the bike rack to the back of the vehicle is 3 inches. We'll now go ahead and pull the hitch switch at the bottom of the bike rack mast to allow the mast to tilt down.
Thule Hitching Post Pro Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry well be test fitting the Thule Hitching Post Pro, part number TH934XTR. To begin our test fit, well slide our bike rack shank into the hitch after removing the two inch adapter from our shank. We can then line up the hitch pin hole where well install and tighten down our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now well give you a few measurements. Our ground clearance at the bike rack is 8 inches and from a closest point of the bike rack to the back of the vehicle is 6 inches.
Thule Apex 4 Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be fitting the Thule Apex 4-bike carrier, partnumber TH9025. Now we've already gone ahead and removed the 2" adapter from our bike rack shank,so we'll go ahead and slide the bike rack shank into the hitch. We'll make sure to pullthe integrated locking hitch pin and allow it to move over our hitch. We'll then allowit to fall into the hitch pin hole where we can move to the back of the shank andtighten the knob down, securing our bike rack to the vehicle. We'll now go ahead and give you a few measurements. Now, our ground clearance atthe bike rack is 9-1/2", and from the closest point of the bike rack to the back of thevehicle is 2-1/2".
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be test fitting part number S64670, theSwagman XTC2 2-bike carrier for both 1-1/4" and 2" hitches. Now to begin our installation we'll remove the 2" adapter from the shank of the bikerack. We can then slide the bike rack shank into the hitch, line up the hitch pin holeand install and tighten down our anti-rattle bolt. With our bolt tight, our bike rack issecured to the vehicle. We'll now go ahead and unfold the bike rack platform andopen the trunk. And as you can see, we can gain access to the cargo area, opening thedeck lid completely, with this bike rack.
SportRack EZ Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be testing the SportRack 2-bike Hitch-mounted Bike Rack for both 1-1/4" and 2" hitches, part number A30901. Now to begin our test fit we've already gone ahead and removed the 2" adapter, sowe'll slide the bike rack shank into the hitch, line up the hitch pin hole, and install andtighten down our anti-rattle bolt. With the bolt tight. our bike rack is secured to thevehicle. Now we'll go ahead and give you a few measurements. Our ground clearanceat the bike rack is 14-1/2", and from the closest point of the bike rack to the back ofthe vehicle is 6-1/2".
