Alright, today on our 2009 Chevrolet Malibu, were gonna do a test fit of part number RG8015220 from Rhode Gear. This is Highway 2 bike carrier. Two things to know about this bike rack is that it will work with 1 -inch receiver hitches both class 1 and class 2. This will also work with 2-inch receiver hitches with the provided spacer. On this car, well be working with the class 2 receiver hitch. Well start off our test fit by installing the bike rack into the hitch and well go ahead and tighten down the anti-rattle bolt then put the safety pin on the other side.
Lets go ahead and get some clearance measurements. From the bike rack to the bumper at its closest point looks like 3. Our ground clearance is 6 inches. Now well go ahead and tilt bike rack out of the way and check the access to the trunk. That looks good.
Lets go ahead and load up a bike. First thing well do is make sure the straps are out of the way for the cradles that were going to use and then well go ahead and place the bike on the cradles, balance it out and then well run the straps over the top tube. And thats what it takes to load up a bike. And with that, thatll finish it for our test fit of part number RG8015220 from Rhode Gear on our 2009 Chevrolet Malibu.
Thule Vertex 4 Hitch Bike Rack Review - 2009 Chevrolet Malibu
Today we have a 2009 Chevrolet Malibu, and we'll be test fitting the Thule vertex four hitch mounted bike carrier. Part number TH9029. To mount our bike rack on our vehicle, we'll fit the shank inside the receiver tube on the hitch. We'll line up the holes and then we'll insert and tighten down our anti rattle bolt. Now we'll give you a couple of clearance measurements. From the ground to the bottom of our bike rack, measures seven inches of ground clearance.
SportRack Escape 3 Hitch Bike Rack Review - 2009 Chevrolet Malibu
Today on our 2012 Ford Fusion, we'll be test fitting part number A30403, the Sport Rack Escape three bike rack. Now to begin our test fit, we'll simply slide the bike rack shank into the hitch, line up the hitch pin hole, and install our anti rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. At this point, we'll give you a few measurements. Our ground clearance at the bike rack is 10 and a half inches, and from the closest point of the bike rack mast to the back of the vehicle is seven and a half inches. We'll now pull the pin at the bottom of the mast to tilt the mast down and open our trunk.
Kuat Alpha Hitch Bike Rack Review - 2009 Chevrolet Malibu
Today we have a 2009 Chevrolet Malibu, and we're going to be test fitting the Kuat Alpha three-bike hitch mounted bike carrier. Part number A103-WHITE-114. To mount our carrier upon our vehicle, we're going to fit the shank into the receiver hitch. We'll line up the hitch pin holes and then we'll tie in the anti rattle device using the hand knob on the end of the bike rack shank. Once we've done that we can insert our pin and secure it with a lock. Next, we'll check for rear vehicle access.
Swagman Titan Hitch Bike Rack Review - 2009 Chevrolet Malibu
Today on this 2009 Chevrolet Malibu were gonna do a test fit of part number S63410 from Swagman. This is Titan 4 Bicycle rack. A few notes about this bike rack is that it will work with 1 -inch receiver hitches both class 1 and class 2. However, when you use it with a class two receiver hitch youre limited to just carrying two bicycles. This will also work with 2-inch receiver hitches with the provided spacer. Now on this car, well be working with a class 2 receiver hitch.
SportRack EZ Hitch Bike Rack Review - 2009 Chevrolet Malibu
Today on this 2009 Chevrolet Malibu were gonna do a test fit of part number A30901 from SportRack. A few things to know about this bike rack is that it will work with 1 -inch receiver hitches both class 1 and class 2. This will also work with 2-inch receiver hitches with the included spacer. On this particular vehicle, well be working with a class 2 receiver hitch. Well start off our test fit by installing the bike rack into the hitch, well tighten down the anti-rattle bolt and then put safety pin on the other side. Lets go ahead and unfold the bike rack and get some clearance measurements.
