Today we will be working on a 2008 Hyundai Santa Fe. We will be installing Curt hitch part number 13538. Here are a couple of measurements that will assist you when ing accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 5-1/2 inches. And from the top of the receiver tube to the ground is 13-3/4 inches. This will assist you with ing accessories such as a draw bar, a bike rack or a cargo carrier. Now let us go ahead with the installation. 0:32
First I would like to point out our fastening points. There are two weld nuts here in the frame. There are an identical two on the passenger side as well. Before we put our hitch into place, what I want to do is spray each of the weld nuts with a little spray lubricant. Then I am going to take a nylon tube brush, this is a 1/2 inch nylon tube brush part number 814092, and I am going to use it to clean out the threads of those weld nuts because over time they will become corroded and fill up with dirt and debris. So now that we have our threads cleaned out, we can go ahead and test fit our hardware. It threads in nicely so we know our weld nuts are cleaned out thoroughly which makes for a much easier installation of our new hitch. 1:23
That completes the two weld nuts on the driver side. I am going to go ahead and repeat the same process on the passenger side. At this time, it may be necessary to get an extra set of hands to help you put the hitch in place. Now that we have all of our fasteners in finger tight, I am going to go ahead and run them down. OK, now that we have our fasteners started on the driver side, I am going to go ahead and repeat the same process on the passenger side. OK, now that we have all of our fasteners tightened down, we are going to go ahead and torque to specifications. Now that we have all of our fasteners torqued to specifications, that completes the installation of Curt hitch part number 13538.
Trailer Hitch Installation - 2013 Hyundai Santa Fe - Curt
Today on our 2013 Hyundai Santa Fe well be installing the Curt hitch, part number C13134. Before we begin our install heres what the hitch looks like when its installed on the vehicle. Well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the inside of the receiver tube opening to the ground is 12 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Curt
Today on our 2012 Hyundai Santa Fe well be installing the Curt hitch, part number C13073. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is four and a half inches. From the top of the receiver tube to the ground is 15 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2011 Hyundai Santa Fe - Draw-Tite
Today on our 2011 Hyundai Santa Fe, we're going to install the Draw-Tite Hitch, part number 36511. This is what our hitch will look once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.
Trailer Hitch Installation - 2010 Hyundai Santa Fe - Draw-Tite
Today on this 2010 Hyundai Santa Fe, were going to install part number 75684 from Draw-Tite. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.
Trailer Hitch Installation - 2008 Hyundai Santa Fe
Today on this 2008 Hyundai Santa Fe, we're going to install part number 87414 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 13 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5-3/4 inches. First thing we'll do is we'll show you where the hitch mounts up to the frame as these two existing threaded holes here. Next step is to go ahead and clean up the threaded holes.
