Today on our 2012 Dodge Ram 2500, we are going to be installing the Pollock fifth wheel and gooseneck T-Connector with seven-pole wiring part number PK11893-11932. First, we need to begin by finding a suitable location for our seven-pole in the bed. Just here past the cut out in the bed behind the drivers side wheel well is where we are going to mount our sub pole connector. First step will be drilling a pilot hole. Ill take my eight-inch bit which will be the same as the pilot hole for hole saw that we will need to cut out. Now I can go underneath and check to make sure its not going to run into anything.
As you can see with our bit in place we have plenty of clearance to go ahead and make our larger hole with our hole saw. Using out hole saw we will now go ahead and drill out so that our socket will fit through the hole. Now with our hole drilled out you can see how our socket is going to mount. However first we need to go ahead and take and route our wires and assemble our connector. First, we will take our wire route it up through the hole from underneath.
Next, we will take our connector and wiring chart, put each pin in the back of the socket going one through seven however quick tack tip before you complete installing all of them I recommend install the center pin as it can be very difficult if all the outer pins have already been connected. Each of these locations is matched in fine print on the back of the connector. We are going to start with number one the red wire then well install number two the white wire, three our blue wire, four the green wire then Ill skip to number seven my yellow wire seven pin then well go back to five the black wire and number six the brown wire. Now with all my pins in place well take the blue lock ring and install it locking each one of our pins in place. Now we can go ahead, and take the connector and lock it in with the back of our seven-pole plug.
With that down, well go ahead, and take our self-tapping screws and secure it to the side of the truck bed. Now with our seven-pole secured we can go ahead and go underneath, well route our wires over to the back of the bumper, well be making connection with the manufacturers wiring and secure our wiring along the way. Now that our wire is routed over behind the bumper, well go ahead and disconnect the connector from the manufacturers seven-pole connection. Now well take the T-Connector portion of our wiring and plug one side to the back of the manufacturers seven-pole connector and the other into the back of the manufacturers seven-pole. Now with all our connections made well go ahead and take some black zip ties to secure our wiring.
With that done this will complete the installation of our Pollock fifth wheel and gooseneck T-Connector with seven-pole wiring, part number PK11893-11932 on our 2012 Dodge Ram 2500.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2005 Dodge Ram
Today on our 2005 Dodge Ram Pickup, well be installing the Bargman 5th Wheel Gooseneck 90 Degree Wiring Harness with 7-Pole plug, part number 51-97-411. To begin our install, well first locate in the pickup bed where well be mounting our 7-pole, then using a smaller bit for our pilot hole, once weve located a spot well go ahead and drill our hole. Well go ahead and drill out using the two inch hole saw as recommended per the instructions. Now with the large hole drilled out, well go ahead and feed half of our T-connector through the hole then our other plug followed by the remainder of the wire until our 7-pole mounts flush with the bed. Then using the self-tapping screws provided with our install kit, we can go ahead and secure the 7-pole plug to the bed side. Next well get underneath the vehicle and start routing our wire over to the back of the bumper where the manufacturers wiring meets the bumper. Here at the back of the bumper, well go ahead and disconnect the manufacturers wiring from the back of the 7-pole plug at the bumper.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2012 Dodge Ram Dully
Today on our 2012 Dodge Ram 3500 dual rear wheel, we'll be installing the Pollak fifth wheel goose neck T-connector with seven pull, part number PK11893-11932. First, we'll go ahead and locate a suitable location for our new seven pull connector. Here, just behind the rear wheel on the driver's side is a common position. Go ahead and locate the area, check underneath to make sure there are no obstructions, and then we'll go ahead and use a small pilot hole and drill it out. This will allow us to again get underneath and double check where the pilot hole location is and correspond it's where our seven pull connector will be. With that done, we can now go ahead and take the hole saw and cut out the larger hole to fit the seven pull connector.
Trailer Wiring Harness Installation - 2011 Dodge Ram
Today on our 2011 Dodge Ram well be installing the Pollak fifth wheel and goose neck connector wiring harness part #: PK11932. First well need to locate a suitable spot for installing the connector in the truck bed. Then Ill take a pilot bit and run it through the bed and double check my location. Were going to go ahead and take a quarter inch bit which will be the same size as my pilot bit for my hole saw and drill out the hole. Now with my hole drilled out well go ahead and take the hole saw and make it large enough for the connector to fit through. With the large hole drilled out we can now take the wiring harness and feed it from underneath through the hole.
Trailer Wiring Harness Installation - 2001 Dodge Ram
Today on this 2001 Dodge Ram pickup 1500 were gonna install part number 118329 from Tow Ready. This is a 4-pole wiring harness. Alright well go ahead and show you where the connection points are if were looking at the driver side of the vehicle it will be right behind the bumper and this is our first connection point right here. inaudible you got to push in that way and you can pull it apart. inaudible the 2 pieces well install the T-connector with the yellow wire, then well route this wire and the 4-pole wire over to the center of the hitch. Well do that by following the factory wire harness inaudible with the green wire and were now on over to the other side.
Fifth Wheel and Gooseneck Wiring Harness Installation - 2004 Dodge Ram 3500
Today on this 2004 Dodge 3500, we are going to install the pre-wired fifth wheel trailer connect that mounts in the pickup bed, part number 51-97-411. Start by looking for a spot to install our assembly connector. We are going to mount ours here, just behind the wheel well in the pickup bed. Using a 1/4 inch bit we will make a pilot hole so that we can use our hole saw bit to drill out a 2 inch hole so that we can mount our connector. Now you can leave your drill bit in the hole, go underneath and check to make sure you have enough clearance to fit your 7 way wiring through. Now we will go ahead and drill it out with our 2 inch hole saw bit.
