Speaker: Today we have with us a 2007 Honda Pilot. Were going to be test fitting Curts 20 inch by 48 inch cargo carrier, part number c18145. To mount our cargo carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch on the Pilot. Well line up the hitch pin holes, thread in our anti rattle bolt and well tighten it down with a three quarter inch wrench finally securing it with a clip on the other side. Now well go over some clearance measurements. Weve got about two and three quarter inches clearance from the furthest part of our vehicle to the closest part of the carrier.
Weve added an over-all length of about 22 and a quarter inches to the rear of our vehicle. From the corner of our carrier to our exhaust tip measures about nine inches so make sure when you load your carrier to keep this in mind. Thats it for our test fit of Curts 20 inch by 48 inch cargo carrier part number c18145 on our 2007 Honda Pilot. .
Curt Folding Hitch Cargo Carrier Review - 2013 Honda Pilot
Today on our 2013 Honda Pilot, well be test fitting the Curt 24 x 60 folding cargo carrier, part number c18132. To install the carrier slide the shank into the opening of the hitch tube and align the pin holes, slide the pin through the pin holes and secure with a safety clip. Now lets go over some clearance measurements to see how the cargo carrier and the vehicle fit together, with the cargo carrier folded up there is about 8-1/2 inches of ground clearance, the closet part of the carrier to the closet part of the vehicle is about two inches with the cargo carrier folded up. With the cargo carrier folded down we have about 23-1/2 inches of ground clearance from the rear of the carrier, the closet part of the carrier to the closet part of the vehicles exhaust tip is about 22 inches, the cargo door extends over the base of the cargo carrier at about 20 inches and that concludes todays test fit for the Curt 24 x 60 folding cargo carrier, part number c18132 on this 2013 Honda Pilot.
Curt Hitch Cargo Carrier Review - 2013 Honda Pilot
Today on our 2013 Honda Pilot well be test fitting the Curt 20 by 48 cargo carrier, part number C18145. To install slide the shank into the opening of the hitch tube and align the threaded pin holes. Thread the anti-rattle bolt through the threaded pin hole and tighten with a wrench. Now lets go over some clearance measurements to see how the cargo carrier and the vehicle fit together. Theres about 18 inches of ground clearance from the back of the carrier. The closest part of the carrier to the closest part of the vehicle is about 5 inch.
UWS Aluminum Cargo Carrier Review - 2007 Honda Pilot
Speaker: Today we have with us the 2007 Honda Pilot. Well be test fitting UWSs 23 inch by 51 inch aluminum cargo carrier part number uws03511. To mount the cargo carrier to our vehicle well insert the shank of the carrier into the receiver tube of our vehicle. Well line up the hitch pin holes, and insert our hitch pin securing it with a clip on the other side. Once weve done that our cargo carrier is installed and ready to load up. Next well go over some clearance measurements.
Surco Folding Hitch Cargo Carrier Review - 2007 Honda Pilot
Speaker: Today we have with us a 2007 Honda Pilot. Well be test fitting Surcos 24 inch by 60 inch folding cargo carrier part number 52018f. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of our hitch. Well line up the hitch pin holes, feed our pin through and secure it with a clip. Now well check for some clearance measurements while we have the cargo carrier still folded up. From the closest point of our carrier to the furthest point of our bumper measures about two and a half inches of clearance.
Curt 20x60 Folding Aluminum Cargo Carrier Review - 2007 Honda Pilot
Speaker: Today we have 2007 Honda Pilot. Well be test fitting Curts 20 inch by 60 inch folding aluminum cargo carrier part number c18100. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of our hitch on the pilot. Well line up the hitch pin holes, feed our pin through and secure it with a clip. Now well go ahead and take a couple of clearance measurements. Weve got about one inch of clearance between the furthest part of our vehicle and the closest point of the carrier.
