Today we are going to be installing part number v82112 which is a Valley Class III Trailer Hitch. We will be installing it on a 2007 Acura RDX turbo model. This hitch installs in 2 points. One is the threading right here. The other point is this hole right here. This hole uses a handle nut which looks like this and goes inside here. Thats what installs the bolt in place and holds it on the inside.
We can start off by raising the hitch up and holding it in place with only a few bolts. The next step is installing our handle nut. It is pretty simple you take it and bend it to the dimension you need. Pop it in there and install your bolt. Going back to your rear mount attachment we will go ahead and replace the rear bolt with a rear bolt and washer. Then do the same thing for the other side. At this point you might want to snug up your bolts. Make sure the hitch is where you want it before you tighten them up. Since we have it where we want it we will go ahead and torque them down. There you have it for install of part number v82112 Valley Class III Trailer Hitch installed on our 2007 Acura RDX turbo model.
Trailer Hitch Installation - 2012 Acura RDX - Curt
Today on our 2012 Acura RDX, well be installing Curt Hitch, part number C13154. Before we start our installation, here are a few measurements that will assist you when selecting accessories, such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 5 inches, and from the top of the reciver tube to the ground is 12 inches. Now, lets go ahead with our install. Now, to begin our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side at the rearmost point is a weld nut, here, and well be using this hole here for our frontmost attachment.
Trailer Hitch Installation - 2012 Acura RDX - Hidden Hitch
Today on our 2012 Acura RDX, well be installing Hidden Hitch, part number 87584. Now, before we start our installation, here are some measurements to help in selecting accessories, such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 4 inches, and from the top of the receiver tube to the ground is 12 inches. Now, lets go ahead with our install. To begin our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side, at the rearmost point, is a weld nut, here, and well be using this hole here for our frontmost attachment.
Trailer Hitch Installation - 2012 Acura RDX - Draw-Tite
Today on our 2012 Acura RDX, well be installing Draw-Tite Hitch, part number 75692. Now, before we start our installation, here are some measurements to help you in selecting accessories such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 4 inches, and from the top of the receiver tube to the ground is 12 inches. Now, lets go ahead with our install. To begin in our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side, at the rear most point, is a weld nut here, and well be using this hole here for our frontmost attachment.
Trailer Hitch Installation - 2008 Acura RDX
Today we are going to be installing part number 75563. Which is a Draw-Tite Class III Trailer Hitch. We will be installing it on a 2007 Acura RDX. This also applies to Hidden Hitch Class 87449. Our hitch install is in 2 different points. This very fitting at the end of the frame and this hole here on this part of the frame. What happens is the bolt gets threaded in here obviously. In this hole here we have a handle nut that fits inside this frame and sits just like that. We are going to thread our bolt in and our hitch is good to go. This is the same on both sides of the vehicle.
