Today we are going to be installing part number 75563. Which is a Draw-Tite Class III Trailer Hitch. We will be installing it on a 2007 Acura RDX. This also applies to Hidden Hitch Class 87449. Our hitch install is in 2 different points. This very fitting at the end of the frame and this hole here on this part of the frame. What happens is the bolt gets threaded in here obviously. In this hole here we have a handle nut that fits inside this frame and sits just like that. We are going to thread our bolt in and our hitch is good to go. This is the same on both sides of the vehicle.
This is where we go ahead and install our hitch. It will be pretty easy, we will go ahead and temporary install our threaded bolts first and then the handle nut bolts. Next we are going to install our handle nut they are pretty neat. What you can do with these is bend the handle as you need them to fit the vehicle your working with then repeat for the other side. Next up go ahead and snug up your bolts. Might want to take a second and rock the hitch back and forth to make sure you have it centered on the bumper where you want it. Once you are sure it is where you want it go ahead and snug the bolts down. We got our hitch snugged down and now we will give them their final torque. There you have it for the install of part number 75563 the Draw-Tite Class III Trailer Hitch on our 2007 Acura RDX.
Trailer Hitch Installation - 2012 Acura RDX - Curt
Today on our 2012 Acura RDX, well be installing Curt Hitch, part number C13154. Before we start our installation, here are a few measurements that will assist you when selecting accessories, such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 5 inches, and from the top of the reciver tube to the ground is 12 inches. Now, lets go ahead with our install. Now, to begin our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side at the rearmost point is a weld nut, here, and well be using this hole here for our frontmost attachment.
Trailer Hitch Installation - 2012 Acura RDX - Hidden Hitch
Today on our 2012 Acura RDX, well be installing Hidden Hitch, part number 87584. Now, before we start our installation, here are some measurements to help in selecting accessories, such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 4 inches, and from the top of the receiver tube to the ground is 12 inches. Now, lets go ahead with our install. To begin our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side, at the rearmost point, is a weld nut, here, and well be using this hole here for our frontmost attachment.
Trailer Hitch Installation - 2012 Acura RDX - Draw-Tite
Today on our 2012 Acura RDX, well be installing Draw-Tite Hitch, part number 75692. Now, before we start our installation, here are some measurements to help you in selecting accessories such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 4 inches, and from the top of the receiver tube to the ground is 12 inches. Now, lets go ahead with our install. To begin in our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side, at the rear most point, is a weld nut here, and well be using this hole here for our frontmost attachment.
Trailer Hitch Installation - 2008 Acura RDX
Today we are going to be installing part number v82112 which is a Valley Class III Trailer Hitch. We will be installing it on a 2007 Acura RDX turbo model. This hitch installs in 2 points. One is the threading right here. The other point is this hole right here. This hole uses a handle nut which looks like this and goes inside here. Thats what installs the bolt in place and holds it on the inside.
