customer service | view cart 
Trailer Hitch Installation - 2006 Dodge Ram
Custom Fit Trailer Hitch
This Product Fits The Following Vehicles
2003 - 2003 Dodge Ram Pickup 1500 Series, built After 11/1/02
2006 - 2008 Dodge Ram Pickup 1500 Series, Except Mega Cab
2006 - 2008 Dodge Ram Pickup 1500 Series, Mega Cab Only
2003 - 2009 Dodge Ram Pickup 2500 and 3500 Series
2004 - 2005 Dodge Ram Pickup All Models
Products Featured in this Video
Manufacturer InstructionsInstallation of a Trailer Hitch on a 2006 Dodge Ram
Today we are going to install part number 75151 from Draw Tite. We will install this on a 2006 Dodge Ram full size pickup. First step involves in some models you might have to lower the spare tire. If you have enough clearance between the bumper so you should not have to lower it. The next step is to go ahead and lower the plastic plate here. There are 4 tabs in the bottom you squeeze so you can flip this up out of the way. To remove the plastic piece these 2 tabs have to be squeezed on the bottom and pushed upwards. Next we install our hardware into the bumper itself. We just a carriage bolt in and the edges will ride in these little holes here a little bit. It kind of sticks up you can see it rock a little bit. We you tighten it down it will pull flush into it.
You can go ahead and install our hitch hanging from these 2 bolts. Next all we have to do is fish wire the bolts into the bumper and pull them out of the back pointing that way. We will go ahead and leave this loose so we can go ahead and have some wiggle room for the bolts to come through. We ran our fish wire into the frame here and what we are going to do is pull it up and through the side of the frame. Make sure you slide your plate on the wire first and then go ahead and thread on your bolt. Pull everything right on through and there you have it. At this point make sure you do not lose the bolt in the frame. Go ahead and repeat for the other side. Once you have all your hardware installed you can go ahead and move it a little bit. Try and get it as center as possible then go ahead and snug down the bolts. After that we can give the bolts their final torque. As you tighten these down you can see the bolt sink into the bumper. Now we can pop our plastic plate back on. That covers it for part number 75151 from Draw Tite.
Filter Videos
- Search By Other Makes
- Acura (4)
- Audi (1)
- BMW (2)
- Buick (5)
- Cadillac (1)
- Chevrolet (36)
- Chrysler (16)
- Dodge (29)
- Ford (44)
- GEO (1)
- GMC (8)
- Honda (24)
- Hyundai (11)
- Infiniti (1)
- Isuzu (1)
- Jeep (18)
- Kia (9)
- Lincoln (2)
- Mazda (11)
- Mercury (2)
- Mitsubishi (4)
- Nissan (12)
- Oldsmobile (2)
- Pontiac (9)
- Saab (1)
- Saturn (4)
- Scion (2)
- Subaru (6)
- Suzuki (1)
- Toyota (27)
- Volkswagen (5)
- Volvo (1)
- Trailer Hitch Help
Specialty Trailer Hitch Review- Trailer Hitch Receiver Sizes
- Trailer Hitch Types Review
- Trailer Hitch Installation Tips
- What Do I Need To Tow A Trailer?
- Trailer Hitch Classes Review
Trailer Hitch Classes and Weight Capacity Comparison- Class I Trailer Hitch and Weight Capacities Review
- Class II Trailer Hitch and Weight Capacities Review
- Class III Trailer Hitch and Weight Capacities Review
- Using Stove Wire as a Bolt Leader Demonstration
- Lowering Exhaust Pipe on Vehicle with Rubber Hanger
- Lowering Exhaust Example for Trailer Hitch Installation
- Using Fish Wire for Trailer Hitch Installation
- Drilling a Spare Tire Pan for a Trailer Hitch Installation
- Drilling to Enlarge a Frame Hole for Hitch Install
- Handle Nut Demonstration
- Cleaning Weld Nuts for Trailer Hitch Installation
Search
Contact and Help
What our customers said:
The phone operator was very helpful and made my purchase easy. I will keep this website handy.
Harold
Gillsville, GA
