Today on this 2009 Hyundai Santa Fe we will be installing Curt part number 13538. A couple of measurements to be aware of when ing accessories, such as a drawbar, bike carrier or cargo carrier, would be from the center of the hitch pin hole to the outer most point of the bumper is 5-1/2 inches. And from the top of the receiver tube to the ground is 15 inches. I would first like to point out where our mounting holes are going to be on the rear sub frame of the vehicle. It is almost identical on each side. These are factory mounted holes and being factory threaded holes what we are going to want to do is make sure those threads are free and clear of any dirt and debris. So I am going to take part number 814092, a nylon tube brush, and some lubricant and flush those holes out now. And again we are just cleaning those threads out to make it easy for our new bolts to go in when we go to install our hitch. 1:04
Then repeat for the driver side. Before I go to install my hitch, I always like to take a new bolt that we will be using for the install. Thread it in just to make sure everything is going to go nice and smoothly. Now that we have our holes prepped for the installation, it is a good idea to have a second set of hands when raising the hitch into position. We will be using the bolts and conical tooth washers. The teeth of the washers will face the bottom of the vehicle. Everything is just finger tight because we want to line up all four bolt holes and get everything started before we start to torque anything down. Alright, now that we have everything lined up and hand tightened down, what we want to do is go ahead and snug everything down and then come back and torque everything to specifications. And that will complete the installation of Curt part number 13538 on a 2009 Hyundai Santa Fe.
Trailer Hitch Installation - 2013 Hyundai Santa Fe - Curt
Today on our 2013 Hyundai Santa Fe well be installing the Curt hitch, part number C13134. Before we begin our install heres what the hitch looks like when its installed on the vehicle. Well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the inside of the receiver tube opening to the ground is 12 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Curt
Today on our 2012 Hyundai Santa Fe well be installing the Curt hitch, part number C13073. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is four and a half inches. From the top of the receiver tube to the ground is 15 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2011 Hyundai Santa Fe - Draw-Tite
Today on our 2011 Hyundai Santa Fe, we're going to install the Draw-Tite Hitch, part number 36511. This is what our hitch will look once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.
Trailer Hitch Installation - 2010 Hyundai Santa Fe - Draw-Tite
Today on this 2010 Hyundai Santa Fe, were going to install part number 75684 from Draw-Tite. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.
Trailer Hitch Installation - 2008 Hyundai Santa Fe
Today on this 2008 Hyundai Santa Fe, we're going to install part number 87414 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 13 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5-3/4 inches. First thing we'll do is we'll show you where the hitch mounts up to the frame as these two existing threaded holes here. Next step is to go ahead and clean up the threaded holes.
