Today we are going to be installing Hidden Hitch part number 87451 on a 2009 Chrysler Town and Country. OK, we are underneath the vehicle and we are looking at the passengers side frame rail. As you can see, the exhaust is in the way of right where we are going to need to get the hitch up into position, so the first thing we are going to need to do is go ahead and lower it down. To do that, we are going to take it off of its main hanger, which is right here. And now, with the exhaust down, I can kind of pull it out of the way. You can see here above the exhaust here we have got one, two existing bolts. We are going to remove those and actually reuse those for the installation. Looking at the drivers side, we are actually going to be using three attaching points. And again, the bolts for those are already in the frame: here, here and here.
Now that we have got all the bolts removed, we can go ahead and put the hitch up into position. Over here on the passengers side, you want to make sure when you put the hitch up that you avoid the AC line here. It might be necessary to slide the hitch a little bit behind the AC line here. You want to make sure that definitely do not have the AC line in between the hitch and the frame. Now that we have got the bolts up into position, we can go ahead and torque them down. You want to check with your directions to verify the appropriate torque rating for each individual bolt. With all the bolts torqued down, we just want to make sure we go ahead and put our exhaust back up on its hanger, and our installation will be complete. And that will conclude the installation of hitch part number 87451 on a 2009 Chrysler Town and Country.
Trailer Hitch Installation - 2013 Chrysler Town and Country - Hidden Hitch
Today on this 2013 Chrysler Town and Country were going to install part number 87451 from Hidden Hitch. This is what the hitch looks like once its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 13 inches. From the center of the hitch pin hole to the edge of the bumper will be about six and a quarter inches. Now well go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2013 Chrysler Town and Country - Draw-Tite
Today on this 2013 Chrysler Town and Country, were going to install part number 75579 from Draw Tite. All right this is what the hitch looks like once its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about 13-1/4 From the center of the hitch pin hole to the edge of the bumper will be about 6-1/4.Now well go ahead and show you how the hitch is installed. The first step is to go ahead and lower the exhaust. Right behind the muffler is a hanger well unbolt and one above the axial that well unbolt as well.
Trailer Hitch Installation - 2013 Chrysler Town and Country - Draw-Tite
Today on this 2013 Chrysler Town and Country, were going to install part number 36455 from Draw Tite. This is what the hitch looks like once its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 13-1/4 and from the center of the hitch pin hole to the outside edge of the bumper will be about 6-3/4. Now well go ahead and show you how the hitch is installed. First thing we need to do before we do our install is to go ahead and lower the exhaust out of the way.
Trailer Hitch Installation - 2007 Chrysler Town and Country - Curt
Today on our 2007 Chrysler Town and Country, well be installing Curt Hitch part number 13389. Now before we begin our installation heres what your hitch will look like on the vehicle. Well go ahead and give you a few measurements to assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. From the top of the receiver tube to the ground measures 12 and from the center of the hitch pin hole to the outer most part of the bumper measures four inches. With that well go ahead and start our installation. To begin our installation, well need to locate the attachment points on the vehicle frame.
Trailer Hitch Installation - 2007 Chrysler Town and Country - Hidden Hitch
Today on our 2007 Chrysler Town and Country, well be installing Hidden Hitch, part number 87719. Now before we begin our install, heres what your hitch will look like on the vehicle. At this point well go ahead and give you a few measurements to help assist you when selecting accessories such as a drawbar, a bike rack or a cargo carrier. From the top of the receiver tube to the ground measures 12 inches and from the center of the 5/8 inch hitch pinhole to the outermost part of the bumper measures 2 inches. Now lets go ahead with our install. Now to begin our installation well need to locate the three attachment points on either side of the frame. Well be using for our rear two attachment points, the two bolts here on the leaf spring shackle.
Trailer Hitch Installation - 2007 Chrysler Town and Country - Draw-Tite
Today on our 2007 Chrysler Town and Country, well be installing Draw-Tite Hitch, part number 75305. Now before we begin our install, heres what your hitch will look like on the vehicle. At this point well go ahead and give you a few measurements to help assist you when selecting accessories such as a drawbar, a bike rack or a cargo carrier. From the top of the receiver tube to the ground measures 12 inches and from the center of the 5/8 inch hitch pinhole to the outermost part of the bumper measures 2 inches. Now lets go ahead with our install. Now to being our installing, well need to locate the three attachment points on either side of the frame.
