customer service | view cart 
Trailer Hitch Installation - 2006 Honda Accord
Custom Fit Trailer Hitch
This Product Fits The Following Vehicles
2003 - 2007 Honda Accord 2 Door
2003 - 2007 Honda Accord 4 Dr. Sedan
Products Featured in this Video
Manufacturer Instructions
Installation of a Trailer Hitch on a 2006 Honda Accord
Today we are going to be installing hitch part number 24787 from Draw-Tite on a 2006 Honda Accord. This installation will also apply to Hidden Hitch part number 60953. We are underneath the vehicle. The first thing we want to do to gain access to the frame rail is to go ahead and lower the exhaust down from the passengers side frame rail. There are actually two hangers that we are going to need to remove to lower the exhaust down. The one here on the outboard side, about midway up the muffler here, that is going to need to be pried off. And I definitely recommend to spray it down with some form of spray lubricant, like a WD-40. It makes the removal a lot easier. And the second exhaust hanger that we are going to need to lower is a little bit forward here of the muffler, right dead center of the car.
Before I remove the second exhaust hanger, I am going to go ahead and use a basic tow strap to support the exhaust tube, so that when I remove the second hanger the exhaust does not fall down and damage the exhaust system. OK, with the exhaust lowered, I am going to go ahead and point out the mounting locations for the trailer hitch. The center mounting location will be to the tow loop here that is mounted on the bottom of the trunk well. And you can see on the drivers side frame rail we have got two existing holes we are going to be using the rearmost hole as our attaching point on the frame rail. And we are going to have the same thing here on the passengers side.
In order to get the hardware into the frame, we are going to be using the fish wire that is provided in the installation kit. We are going to take the 7/16 block, which you can see has a few notches cut out in it, and the 7/16 carriage bolt, as well. These are going to up into this hole, and then we are going to pull it back down into place. To do that, we just want to go ahead and feed the fish wire into the block and then wrap the threads of the carriage bolt with the fish wire and feed it up into the hole, followed by the block. And we want to put the notches in first that is going to allow it to go into the frame a little bit easier. And then we just pull it back down into position. And we are going to do that on the passengers side location, as well. And with those two fasteners in place, we can go ahead and put our hitch up into position. I am actually going to attach it to the center tow hook first. We are going to put the 1/2-inch carriage bolt in through.
We are going to take the flat block and place it on the other side. We will come over to the bottom of the frame and go ahead and lift the arm up into position. And again, we are just going to attach this tie with the 7/16 conical-tooth washer and the 7/16 nut. Now that we have got all of the hardware into position, we can go ahead and torque all of our bolts down. We are going to start by torquing the ones at the bottom of the frame on each side first, and then we will come back and torque the one for the center tow hook attaching point last. You want to check with your directions to verify the appropriate torque rating for each individual bolt. And with all of our bolts torqued down, we want to make sure we put our exhaust back up on its hangers, and our installation will be complete. This will conclude the installation of hitch part number 24787 from Draw-Tite on a 2006 Honda Accord.
Questions About Part 60953
Filter Videos
- Search By Other Makes
- Acura (4)
- Audi (1)
- BMW (2)
- Buick (5)
- Cadillac (1)
- Chevrolet (36)
- Chrysler (16)
- Dodge (29)
- Ford (44)
- GEO (1)
- GMC (8)
- Honda (24)
- Hyundai (11)
- Infiniti (1)
- Isuzu (1)
- Jeep (18)
- Kia (9)
- Lincoln (2)
- Mazda (11)
- Mercury (2)
- Mitsubishi (4)
- Nissan (12)
- Oldsmobile (2)
- Pontiac (9)
- Saab (1)
- Saturn (4)
- Scion (2)
- Subaru (6)
- Suzuki (1)
- Toyota (27)
- Volkswagen (5)
- Volvo (1)
- Trailer Hitch Help
Specialty Trailer Hitch Review- Trailer Hitch Receiver Sizes
- Trailer Hitch Types Review
- Trailer Hitch Installation Tips
- What Do I Need To Tow A Trailer?
- Trailer Hitch Classes Review
Trailer Hitch Classes and Weight Capacity Comparison- Class I Trailer Hitch and Weight Capacities Review
- Class II Trailer Hitch and Weight Capacities Review
- Class III Trailer Hitch and Weight Capacities Review
- Using Stove Wire as a Bolt Leader Demonstration
- Lowering Exhaust Pipe on Vehicle with Rubber Hanger
- Lowering Exhaust Example for Trailer Hitch Installation
- Using Fish Wire for Trailer Hitch Installation
- Drilling a Spare Tire Pan for a Trailer Hitch Installation
- Drilling to Enlarge a Frame Hole for Hitch Install
- Handle Nut Demonstration
- Cleaning Weld Nuts for Trailer Hitch Installation
Search
Contact and Help
What our customers said:
The phone operator was very helpful and made my purchase easy. I will keep this website handy.
Harold
Gillsville, GA
