Today on this 2002 Chevrolet Impala we are going to install part number 118002 from Tow Ready. This wiring harness is pretty easy to install because everything is going to be available to hook into on passenger side of the vehicle behind the carpet here. I have theses fasteners here just to make it a little easier to get the carpet down. All right and with this wiring harness right here we will go ahead and test each individual wire to find out its function and we will go ahead and make the appropriate connection.
First off we will actually make a ground. All right we will go ahead and cover the wire coding for our 4-pole wiring harness here. The ground is going to be white. The running lights circuit will be brown. The left turn is going to be yellow and the right turn is going to be green. Then we will test our wires. We will go ahead and test for our running lights. Okay it looks like brown with the white trace is going to be the running light circuit. So we will go ahead and make our connection now to the 4-pole wiring harness. Slide our quick splice over the wire and put the brown wire through, and that is going to be our running lights.
That is our right turn, the green in our 4-pole harness is going to be right turn also. Okay so that is our left turn circuit so go ahead and hook that up. Okay now go ahead and hook up the ground. Since we have a screw here we will just add on a simple ring terminal and then just attach it to the body here. All right all we are going to do now is put our carpet back into place, keep the 4-pole out, and screw our fasteners back in and we are good to go. Obviously the 4-pull is going to stay in the trunk area when you are not using it. When you do need to use it go ahead and just lay it out, stay away from the latch, and you can shut the trunk on it. The weather strip is so thick it will not mash the wire. Then just pull our what you need out to your trailer hitch. With that, that finishes our install of part number 118002 from Tow Ready.
Today, on a 2005 Chevrolet Impala, we are going to install part number 118512 to be tow ready. The first thing we need to do is go ahead and open up the trunk and get access to the wiring harness. We will have to remove the interior panels and the threshold to get to it. First off, we are going to go ahead and remove the plastic rivets from our cover right here. Next, we are going to remove these 2 fasteners here and here. Now, we are going to remove this fastener right here and this fastener here and then we can go ahead and remove the taillight.
Today on our 2012 Chevy Impala we're going to install tow ready T1 Connector part number 118417. First we are going to need to access the rear cargo area. Then our first step will be removing the rear threshold. There are a couple of fasteners that will need to be removed first. Now we are going to get our trim tool or a flat headed screw driver to get underneath the threshold and just pry it up. There's several plastic fasteners underneath threshold still holding it in place.
Today on this 2003 Chevrolet Impala we are going to be installing hard wiring kit 18252. The first thing we need to do is remove the driver side tail light. We are going to undo the tie down screw. Fold back the carpeting in the trunk and as you can see there is three more tail light screws that we are going to be removing and that will pop loose our tail light. Now that our tail light is removed we are going to unplug it and set it out of the way. As you can see these are the wires that we are going to be tapping into. Before we tap into our wires, take the 4-pole and run it down through the bumper and out the bottom. We are going to test our wires to see what function they are going to be. 00:45
Today we are going to be installing a 4-pole, part number 118002, on a 2004 Chevrolet Impala. OK, we are inside the trunk area, and we want to go ahead and access the wires that we are going to be tapping into for our wiring harness. Those wires are actually located directly behind the tail light assemblies on both sides of the vehicle. In order to gain access to those wires, we are going to need to go inside the trunk area and we will first off need to remove these three screws per side and then pull back our carpeting. And you can actually see there are two more set screws that we are going to need to remove as well. And with all the set screws removed, I can go ahead and pull the tail light assembly off. As you can see, here is our main wiring harness, feeding the drivers side tail light assembly here. We have got three wires here. We have got a brown with white, which is going to be the running light lead that we are going to be tapping into the yellow, which is our left turn and left brake signal and then the black, which is the standard ground. And then what we want to do is to take our yellow wire here off of our wiring harness, and we want to go ahead and we are going to attach it directly to the yellow wire on our tail light assembly.
Today we are going to install part number 118417 from Tow Ready. We are going to install this on a 2007 Chevrolet Impala. To install the T-1 connector, we have to get back behind the tail light assembly here and behind this plastic. We are also going to be taking off the passengers side tail light, too. And this whole panel will just pop up straight vertical. And we are going to take off this other wing nut right here. Now that we have got our tail light loose, we are going to just temporarily disconnect it from the wiring harness. And then this actual plug right here is where our T-1 connector is going to hook up to the vehicle. We will reconnect the T-1 connector back in, and just tuck that back between the bumper fascia and the body. And we are also going to take our 4-pole wire, and we are going to route that straight down, because that is going to come out by the hitch itself. Make sure to leave that ground wire, because we are going to attach it to the sheet metal below the tail light. And we will just clip our original wire harness back on.