Today, on this 2001 Dodge Ram 2500, we are going to install Timbren front suspension kit, part number TDF25004B. Alright, this is the Timbren suspension enhancement system and we are seeing half of the kit. This is the part that we are going to use on the driver side of the vehicle. Alright, as you can see here, it has the rubber spring on the bottom half and then on the top part is a thin metal plate. And then on top of that is another rubber part that can actually get pushed into the bump stop cup that is located on the frame of the vehicle. What you need to do is lift the frame of the vehicle up to loosen the suspension up, so we have more working room. 0:32
Alright, we are going to show you where the factory bump stop is. This is the actual part right here. Now, since it is a friction fit, so all we have to do is just pry it out of position. We are just going to use a screw driver to just push on it to pry it out. And next we are going to go ahead and put our new component into place. We are just going to push it in there, line it up and get it started as best we can. Then, we will lower the truck to push it in the rest of the way. Now let us go ahead and let everything rest in its final position. With the rubber springs installed, you will notice that they do touch on the bottom, on the bump stop too. It is designed to work that way. Alright, with the second one finished, that concludes our install of part number TDF25004B from Timbren.
Today on our 2012 Dodge Ram Pickup we'll be installing the Firestone Coil Rite Air Springs with Work Rite Helper Spring Kit, part number f4190. To begin our installation we'll need to deflate both airbags. To do this we'll take a small piece of air tube and connect it to the airbag. We can then deflate the airbag where we'll take the inflation valve slide it over the air tube with the airbag deflated. This will keep the airbag deflated and allow us to install it into our spring.We'll then push the air spring up into the coil spring by hand. You may need to use a blunt tool making sure that it doesnt have any sharp edges or corners as this could damage the air spring.
Today on our 2003 Dodge Ram 2500 we'll be installing Timbren Suspension Enhancement System, part number TDR2500CA. Now this will be for the rear. Now before installing the Timbrens you may need to raise the vehicle to allow the axle to hang freely. We'll need to remove the existing bump stops. We'll take out the two bolts holding it in place. Now we'll need to keep the bolts as we will reuse them when installing our Timbren Suspension.
Today on our 2003 Dodge Ram 2500 we'll be installing the Timbren Suspension Enhancement System, part number TDF25004B on the front axle. Now to begin our installation we'll need to raise the vehicle to allow the axle to hang freely. We'll remove the existing bump stops by prying it out of the bump stop cup. We can then position the Timbren Spring Assembly into the bump stop cup and press it into place. You may need to use a soapy water as a lubricant to get it up into the cup. With your spring assembly loosely fit into the cup we can then use a piece of wood such as a 2x4 to place between the spring and the axle itself.
Today on this 2009 Dodge Ram 1500, were going to install part number TDR1500DQ from Timbren. First thing we need to do is go ahead and raise the vehicle up and then well go ahead and remove the factory bump stops. Alright, now weve got the old ones removed, we'll now go ahead and install the new Timbren. Well go ahead and spray some soapy water on it and our Timbren has already come pre-assembled in a package, so all we got to do is install it on the vehicle. Were going to fit up into the cup right here. So what well do, well start it, put in place with pieces of little piece of timber between two and lower the truck onto it so it pushes the Timbren part up into the cup.
Today we are working on a 2007 Dodge Ram 1500, we will be installing Firestone Air Spring Kit part number F2286. Per the instructions it is not necessary to take the wheels off the vehicle, but we found that this application is much easier if you do so. Our first step will be to remove the manufactures bum stops. They are two fasteners, one on each side. Now that we have our bum stop removed, we will come over to our air bag and get it set up. :33
Dodge Ram 3500 SuperCoils Manufacturer Demo